rombios.c@ 15712

Last change on this file since 15712 was 15712, checked in by vboxsync, 16 years ago
dpte_offset & dpte_segment reversed. Fixed in upstream Bochs. Reported in #2648.
Property svn:eol-style set to `native`
File size: 328.6 KB

Line
1	/////////////////////////////////////////////////////////////////////////
2	// $Id: rombios.c,v 1.176 2006/12/30 17:13:17 vruppert Exp $
3	/////////////////////////////////////////////////////////////////////////
4	//
5	// Copyright (C) 2002 MandrakeSoft S.A.
6	//
7	// MandrakeSoft S.A.
8	// 43, rue d'Aboukir
9	// 75002 Paris - France
10	// http://www.linux-mandrake.com/
11	// http://www.mandrakesoft.com/
12	//
13	// This library is free software; you can redistribute it and/or
14	// modify it under the terms of the GNU Lesser General Public
15	// License as published by the Free Software Foundation; either
16	// version 2 of the License, or (at your option) any later version.
17	//
18	// This library is distributed in the hope that it will be useful,
19	// but WITHOUT ANY WARRANTY; without even the implied warranty of
20	// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
21	// Lesser General Public License for more details.
22	//
23	// You should have received a copy of the GNU Lesser General Public
24	// License along with this library; if not, write to the Free Software
25	// Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
26
27
28	/*
29	* Sun LGPL Disclaimer: For the avoidance of doubt, except that if any license choice
30	* other than GPL or LGPL is available it will apply instead, Sun elects to use only
31	* the Lesser General Public License version 2.1 (LGPLv2) at this time for any software where
32	* a choice of LGPL license versions is made available with the language indicating
33	* that LGPLv2 or any later version may be used, or where a choice of which version
34	* of the LGPL is applied is otherwise unspecified.
35	*/
36	// ROM BIOS for use with Bochs/Plex86/QEMU emulation environment
37
38
39	// ROM BIOS compatability entry points:
40	// ===================================
41	// $e05b ; POST Entry Point
42	// $e2c3 ; NMI Handler Entry Point
43	// $e3fe ; INT 13h Fixed Disk Services Entry Point
44	// $e401 ; Fixed Disk Parameter Table
45	// $e6f2 ; INT 19h Boot Load Service Entry Point
46	// $e6f5 ; Configuration Data Table
47	// $e729 ; Baud Rate Generator Table
48	// $e739 ; INT 14h Serial Communications Service Entry Point
49	// $e82e ; INT 16h Keyboard Service Entry Point
50	// $e987 ; INT 09h Keyboard Service Entry Point
51	// $ec59 ; INT 13h Diskette Service Entry Point
52	// $ef57 ; INT 0Eh Diskette Hardware ISR Entry Point
53	// $efc7 ; Diskette Controller Parameter Table
54	// $efd2 ; INT 17h Printer Service Entry Point
55	// $f045 ; INT 10 Functions 0-Fh Entry Point
56	// $f065 ; INT 10h Video Support Service Entry Point
57	// $f0a4 ; MDA/CGA Video Parameter Table (INT 1Dh)
58	// $f841 ; INT 12h Memory Size Service Entry Point
59	// $f84d ; INT 11h Equipment List Service Entry Point
60	// $f859 ; INT 15h System Services Entry Point
61	// $fa6e ; Character Font for 320x200 & 640x200 Graphics (lower 128 characters)
62	// $fe6e ; INT 1Ah Time-of-day Service Entry Point
63	// $fea5 ; INT 08h System Timer ISR Entry Point
64	// $fef3 ; Initial Interrupt Vector Offsets Loaded by POST
65	// $ff53 ; IRET Instruction for Dummy Interrupt Handler
66	// $ff54 ; INT 05h Print Screen Service Entry Point
67	// $fff0 ; Power-up Entry Point
68	// $fff5 ; ASCII Date ROM was built - 8 characters in MM/DD/YY
69	// $fffe ; System Model ID
70
71	// NOTES for ATA/ATAPI driver (cbbochs@free.fr)
72	// Features
73	// - supports up to 4 ATA interfaces
74	// - device/geometry detection
75	// - 16bits/32bits device access
76	// - pchs/lba access
77	// - datain/dataout/packet command support
78	//
79	// NOTES for El-Torito Boot (cbbochs@free.fr)
80	// - CD-ROM booting is only available if ATA/ATAPI Driver is available
81	// - Current code is only able to boot mono-session cds
82	// - Current code can not boot and emulate a hard-disk
83	// the bios will panic otherwise
84	// - Current code also use memory in EBDA segement.
85	// - I used cmos byte 0x3D to store extended information on boot-device
86	// - Code has to be modified modified to handle multiple cdrom drives
87	// - Here are the cdrom boot failure codes:
88	// 1 : no atapi device found
89	// 2 : no atapi cdrom found
90	// 3 : can not read cd - BRVD
91	// 4 : cd is not eltorito (BRVD)
92	// 5 : cd is not eltorito (ISO TAG)
93	// 6 : cd is not eltorito (ELTORITO TAG)
94	// 7 : can not read cd - boot catalog
95	// 8 : boot catalog : bad header
96	// 9 : boot catalog : bad platform
97	// 10 : boot catalog : bad signature
98	// 11 : boot catalog : bootable flag not set
99	// 12 : can not read cd - boot image
100	//
101	// ATA driver
102	// - EBDA segment.
103	// I used memory starting at 0x121 in the segment
104	#ifndef VBOX
105	// - the translation policy is defined in cmos regs 0x39 & 0x3a
106	#endif /* !VBOX */
107	//
108	// TODO :
109	//
110	// int74
111	// - needs to be reworked. Uses direct [bp] offsets. (?)
112	//
113	// int13:
114	// - f04 (verify sectors) isn't complete (?)
115	// - f02/03/04 should set current cyl,etc in BDA (?)
116	// - rewrite int13_relocated & clean up int13 entry code
117	//
118	// NOTES:
119	// - NMI access (bit7 of addr written to 70h)
120	//
121	// ATA driver
122	// - should handle the "don't detect" bit (cmos regs 0x3b & 0x3c)
123	// - could send the multiple-sector read/write commands
124	//
125	// El-Torito
126	// - Emulate a Hard-disk (currently only diskette can be emulated) see "FIXME ElTorito Harddisk"
127	// - Implement remaining int13_cdemu functions (as defined by El-Torito specs)
128	// - cdrom drive is hardcoded to ide 0 device 1 in several places. see "FIXME ElTorito Hardcoded"
129	// - int13 Fix DL when emulating a cd. In that case DL is decremented before calling real int13.
130	// This is ok. But DL should be reincremented afterwards.
131	// - Fix all "FIXME ElTorito Various"
132	// - should be able to boot any cdrom instead of the first one
133	//
134	// BCC Bug: find a generic way to handle the bug of #asm after an "if" (fixed in 0.16.7)
135
136	#ifdef VBOX
137	#include "DevPcBios.h"
138	#include <VBox/version.h>
139	#endif
140
141	#define BX_ROMBIOS32 0
142	#define DEBUG_ROMBIOS 0
143
144	#define DEBUG_ATA 0
145	#define DEBUG_INT13_HD 0
146	#define DEBUG_INT13_CD 0
147	#define DEBUG_INT13_ET 0
148	#define DEBUG_INT13_FL 0
149	#define DEBUG_INT15 0
150	#define DEBUG_INT16 0
151	#define DEBUG_INT1A 0
152	#define DEBUG_INT74 0
153	#define DEBUG_APM 0
154
155	#define BX_CPU 3
156	#define BX_USE_PS2_MOUSE 1
157	#define BX_CALL_INT15_4F 1
158	#define BX_USE_EBDA 1
159	#define BX_SUPPORT_FLOPPY 1
160	#define BX_FLOPPY_ON_CNT 37 /* 2 seconds */
161	#define BX_PCIBIOS 1
162	#define BX_APM 1
163
164	#define BX_USE_ATADRV 1
165	#define BX_ELTORITO_BOOT 1
166
167	#define BX_MAX_ATA_INTERFACES 4
168	#define BX_MAX_ATA_DEVICES (BX_MAX_ATA_INTERFACES*2)
169
170	#define BX_VIRTUAL_PORTS 1 /* normal output to Bochs ports */
171	#define BX_DEBUG_SERIAL 0 /* output to COM1 */
172
173	/* model byte 0xFC = AT */
174	#define SYS_MODEL_ID 0xFC
175	#define SYS_SUBMODEL_ID 0x00
176	#define BIOS_REVISION 1
177	#define BIOS_CONFIG_TABLE 0xe6f5
178
179	#ifndef BIOS_BUILD_DATE
180	# define BIOS_BUILD_DATE "06/23/99"
181	#endif
182
183	// 1K of base memory used for Extended Bios Data Area (EBDA)
184	// EBDA is used for PS/2 mouse support, and IDE BIOS, etc.
185	#define EBDA_SEG 0x9FC0
186	#define EBDA_SIZE 1 // In KiB
187	#define BASE_MEM_IN_K (640 - EBDA_SIZE)
188
189	#define ACPI_DATA_SIZE 0x00010000L
190
191	// Define the application NAME
192	#if defined(BX_QEMU)
193	# define BX_APPNAME "QEMU"
194	#elif defined(PLEX86)
195	# define BX_APPNAME "Plex86"
196	#else
197	# define BX_APPNAME "Bochs"
198	#endif
199
200	// Sanity Checks
201	#if BX_USE_ATADRV && BX_CPU<3
202	# error The ATA/ATAPI Driver can only to be used with a 386+ cpu
203	#endif
204	#if BX_USE_ATADRV && !BX_USE_EBDA
205	# error ATA/ATAPI Driver can only be used if EBDA is available
206	#endif
207	#if BX_ELTORITO_BOOT && !BX_USE_ATADRV
208	# error El-Torito Boot can only be use if ATA/ATAPI Driver is available
209	#endif
210	#if BX_PCIBIOS && BX_CPU<3
211	# error PCI BIOS can only be used with 386+ cpu
212	#endif
213	#if BX_APM && BX_CPU<3
214	# error APM BIOS can only be used with 386+ cpu
215	#endif
216
217	#if defined(VBOX) && !BX_USE_ATADRV
218	# error VBOX requires enabling the ATA/ATAPI driver
219	#endif
220
221	#ifdef VBOX_WITH_SCSI
222	# define BX_MAX_SCSI_DEVICES 1
223	#endif
224
225	#ifndef VBOX
226	#define PANIC_PORT 0x400
227	#define PANIC_PORT2 0x401
228	#define INFO_PORT 0x402
229	#define DEBUG_PORT 0x403
230	#else /* VBOX */
231	/* Redirect INFO output to backdoor logging port. */
232	#define PANIC_PORT 0x400
233	#define PANIC_PORT2 0x401
234	#define INFO_PORT 0x504
235	#define DEBUG_PORT 0x403
236	#endif /* VBOX */
237
238	// define this if you want to make PCIBIOS working on a specific bridge only
239	// undef enables PCIBIOS when at least one PCI device is found
240	// i440FX is emulated by Bochs and QEMU
241	#define PCI_FIXED_HOST_BRIDGE 0x12378086 ;; i440FX PCI bridge
242
243	// #20 is dec 20
244	// #$20 is hex 20 = 32
245	// #0x20 is hex 20 = 32
246	// LDA #$20
247	// JSR $E820
248	// LDD .i,S
249	// JSR $C682
250	// mov al, #$20
251
252	// all hex literals should be prefixed with '0x'
253	// grep "#[0-9a-fA-F][0-9a-fA-F]" rombios.c
254	// no mov SEG-REG, #value, must mov register into seg-reg
255	// grep -i "mov[ ]*.s" rombios.c
256
257	// This is for compiling with gcc2 and gcc3
258	#define ASM_START #asm
259	#define ASM_END #endasm
260
261	ASM_START
262	.rom
263
264	.org 0x0000
265
266	#if BX_CPU >= 3
267	use16 386
268	#else
269	use16 286
270	#endif
271
272	MACRO HALT
273	;; the HALT macro is called with the line number of the HALT call.
274	;; The line number is then sent to the PANIC_PORT, causing Bochs/Plex
275	;; to print a BX_PANIC message. This will normally halt the simulation
276	;; with a message such as "BIOS panic at rombios.c, line 4091".
277	;; However, users can choose to make panics non-fatal and continue.
278	#if BX_VIRTUAL_PORTS
279	mov dx,#PANIC_PORT
280	mov ax,#?1
281	out dx,ax
282	#else
283	mov dx,#0x80
284	mov ax,#?1
285	out dx,al
286	#endif
287	MEND
288
289	MACRO JMP_AP
290	db 0xea
291	dw ?2
292	dw ?1
293	MEND
294
295	MACRO SET_INT_VECTOR
296	mov ax, ?3
297	mov ?1*4, ax
298	mov ax, ?2
299	mov ?1*4+2, ax
300	MEND
301
302	ASM_END
303
304	typedef unsigned char Bit8u;
305	typedef unsigned short Bit16u;
306	typedef unsigned short bx_bool;
307	typedef unsigned long Bit32u;
308
309	#if BX_USE_ATADRV
310
311	void memsetb(seg,offset,value,count);
312	void memcpyb(dseg,doffset,sseg,soffset,count);
313	void memcpyd(dseg,doffset,sseg,soffset,count);
314
315	// memset of count bytes
316	void
317	memsetb(seg,offset,value,count)
318	Bit16u seg;
319	Bit16u offset;
320	Bit16u value;
321	Bit16u count;
322	{
323	ASM_START
324	push bp
325	mov bp, sp
326
327	push ax
328	push cx
329	push es
330	push di
331
332	mov cx, 10[bp] ; count
333	cmp cx, #0x00
334	je memsetb_end
335	mov ax, 4[bp] ; segment
336	mov es, ax
337	mov ax, 6[bp] ; offset
338	mov di, ax
339	mov al, 8[bp] ; value
340	cld
341	rep
342	stosb
343
344	memsetb_end:
345	pop di
346	pop es
347	pop cx
348	pop ax
349
350	pop bp
351	ASM_END
352	}
353
354	#if 0
355	// memcpy of count bytes
356	void
357	memcpyb(dseg,doffset,sseg,soffset,count)
358	Bit16u dseg;
359	Bit16u doffset;
360	Bit16u sseg;
361	Bit16u soffset;
362	Bit16u count;
363	{
364	ASM_START
365	push bp
366	mov bp, sp
367
368	push ax
369	push cx
370	push es
371	push di
372	push ds
373	push si
374
375	mov cx, 12[bp] ; count
376	cmp cx, #0x0000
377	je memcpyb_end
378	mov ax, 4[bp] ; dsegment
379	mov es, ax
380	mov ax, 6[bp] ; doffset
381	mov di, ax
382	mov ax, 8[bp] ; ssegment
383	mov ds, ax
384	mov ax, 10[bp] ; soffset
385	mov si, ax
386	cld
387	rep
388	movsb
389
390	memcpyb_end:
391	pop si
392	pop ds
393	pop di
394	pop es
395	pop cx
396	pop ax
397
398	pop bp
399	ASM_END
400	}
401
402	// memcpy of count dword
403	void
404	memcpyd(dseg,doffset,sseg,soffset,count)
405	Bit16u dseg;
406	Bit16u doffset;
407	Bit16u sseg;
408	Bit16u soffset;
409	Bit16u count;
410	{
411	ASM_START
412	push bp
413	mov bp, sp
414
415	push ax
416	push cx
417	push es
418	push di
419	push ds
420	push si
421
422	mov cx, 12[bp] ; count
423	cmp cx, #0x0000
424	je memcpyd_end
425	mov ax, 4[bp] ; dsegment
426	mov es, ax
427	mov ax, 6[bp] ; doffset
428	mov di, ax
429	mov ax, 8[bp] ; ssegment
430	mov ds, ax
431	mov ax, 10[bp] ; soffset
432	mov si, ax
433	cld
434	rep
435	movsd
436
437	memcpyd_end:
438	pop si
439	pop ds
440	pop di
441	pop es
442	pop cx
443	pop ax
444
445	pop bp
446	ASM_END
447	}
448	#endif
449	#endif //BX_USE_ATADRV
450
451	// read_dword and write_dword functions
452	static Bit32u read_dword();
453	static void write_dword();
454
455	Bit32u
456	read_dword(seg, offset)
457	Bit16u seg;
458	Bit16u offset;
459	{
460	ASM_START
461	push bp
462	mov bp, sp
463
464	push bx
465	push ds
466	mov ax, 4[bp] ; segment
467	mov ds, ax
468	mov bx, 6[bp] ; offset
469	mov ax, [bx]
470	inc bx
471	inc bx
472	mov dx, [bx]
473	;; ax = return value (word)
474	;; dx = return value (word)
475	pop ds
476	pop bx
477
478	pop bp
479	ASM_END
480	}
481
482	void
483	write_dword(seg, offset, data)
484	Bit16u seg;
485	Bit16u offset;
486	Bit32u data;
487	{
488	ASM_START
489	push bp
490	mov bp, sp
491
492	push ax
493	push bx
494	push ds
495	mov ax, 4[bp] ; segment
496	mov ds, ax
497	mov bx, 6[bp] ; offset
498	mov ax, 8[bp] ; data word
499	mov [bx], ax ; write data word
500	inc bx
501	inc bx
502	mov ax, 10[bp] ; data word
503	mov [bx], ax ; write data word
504	pop ds
505	pop bx
506	pop ax
507
508	pop bp
509	ASM_END
510	}
511
512	// Bit32u (unsigned long) and long helper functions
513	ASM_START
514
515	;; and function
516	landl:
517	landul:
518	SEG SS
519	and ax,[di]
520	SEG SS
521	and bx,2[di]
522	ret
523
524	;; add function
525	laddl:
526	laddul:
527	SEG SS
528	add ax,[di]
529	SEG SS
530	adc bx,2[di]
531	ret
532
533	;; cmp function
534	lcmpl:
535	lcmpul:
536	and eax, #0x0000FFFF
537	shl ebx, #16
538	add eax, ebx
539	shr ebx, #16
540	SEG SS
541	cmp eax, dword ptr [di]
542	ret
543
544	;; sub function
545	lsubl:
546	lsubul:
547	SEG SS
548	sub ax,[di]
549	SEG SS
550	sbb bx,2[di]
551	ret
552
553	;; mul function
554	lmull:
555	lmulul:
556	and eax, #0x0000FFFF
557	shl ebx, #16
558	add eax, ebx
559	SEG SS
560	mul eax, dword ptr [di]
561	mov ebx, eax
562	shr ebx, #16
563	ret
564
565	;; dec function
566	ldecl:
567	ldecul:
568	SEG SS
569	dec dword ptr [bx]
570	ret
571
572	;; or function
573	lorl:
574	lorul:
575	SEG SS
576	or ax,[di]
577	SEG SS
578	or bx,2[di]
579	ret
580
581	;; inc function
582	lincl:
583	lincul:
584	SEG SS
585	inc dword ptr [bx]
586	ret
587
588	;; tst function
589	ltstl:
590	ltstul:
591	and eax, #0x0000FFFF
592	shl ebx, #16
593	add eax, ebx
594	shr ebx, #16
595	test eax, eax
596	ret
597
598	;; sr function
599	lsrul:
600	mov cx,di
601	jcxz lsr_exit
602	and eax, #0x0000FFFF
603	shl ebx, #16
604	add eax, ebx
605	lsr_loop:
606	shr eax, #1
607	loop lsr_loop
608	mov ebx, eax
609	shr ebx, #16
610	lsr_exit:
611	ret
612
613	;; sl function
614	lsll:
615	lslul:
616	mov cx,di
617	jcxz lsl_exit
618	and eax, #0x0000FFFF
619	shl ebx, #16
620	add eax, ebx
621	lsl_loop:
622	shl eax, #1
623	loop lsl_loop
624	mov ebx, eax
625	shr ebx, #16
626	lsl_exit:
627	ret
628
629	idiv_:
630	cwd
631	idiv bx
632	ret
633
634	idiv_u:
635	xor dx,dx
636	div bx
637	ret
638
639	ldivul:
640	and eax, #0x0000FFFF
641	shl ebx, #16
642	add eax, ebx
643	xor edx, edx
644	SEG SS
645	mov bx, 2[di]
646	shl ebx, #16
647	SEG SS
648	mov bx, [di]
649	div ebx
650	mov ebx, eax
651	shr ebx, #16
652	ret
653
654	ASM_END
655
656	// for access to RAM area which is used by interrupt vectors
657	// and BIOS Data Area
658
659	typedef struct {
660	unsigned char filler1[0x400];
661	unsigned char filler2[0x6c];
662	Bit16u ticks_low;
663	Bit16u ticks_high;
664	Bit8u midnight_flag;
665	} bios_data_t;
666
667	#define BiosData ((bios_data_t *) 0)
668
669	#if BX_USE_ATADRV
670	typedef struct {
671	Bit16u heads; // # heads
672	Bit16u cylinders; // # cylinders
673	Bit16u spt; // # sectors / track
674	} chs_t;
675
676	// DPTE definition
677	typedef struct {
678	Bit16u iobase1;
679	Bit16u iobase2;
680	Bit8u prefix;
681	Bit8u unused;
682	Bit8u irq;
683	Bit8u blkcount;
684	Bit8u dma;
685	Bit8u pio;
686	Bit16u options;
687	Bit16u reserved;
688	Bit8u revision;
689	Bit8u checksum;
690	} dpte_t;
691
692	typedef struct {
693	Bit8u iface; // ISA or PCI
694	Bit16u iobase1; // IO Base 1
695	Bit16u iobase2; // IO Base 2
696	Bit8u irq; // IRQ
697	} ata_channel_t;
698
699	typedef struct {
700	Bit8u type; // Detected type of ata (ata/atapi/none/unknown/scsi)
701	Bit8u device; // Detected type of attached devices (hd/cd/none)
702	Bit8u removable; // Removable device flag
703	Bit8u lock; // Locks for removable devices
704	// Bit8u lba_capable; // LBA capable flag - always yes for bochs devices
705	Bit8u mode; // transfert mode : PIO 16/32 bits - IRQ - ISADMA - PCIDMA
706	Bit16u blksize; // block size
707
708	Bit8u translation; // type of translation
709	chs_t lchs; // Logical CHS
710	chs_t pchs; // Physical CHS
711
712	Bit32u sectors; // Total sectors count
713	} ata_device_t;
714
715	typedef struct {
716	// ATA channels info
717	ata_channel_t channels[BX_MAX_ATA_INTERFACES];
718
719	// ATA devices info
720	ata_device_t devices[BX_MAX_ATA_DEVICES];
721	//
722	// map between (bios hd id - 0x80) and ata channels and scsi disks.
723	#ifdef VBOX_WITH_SCSI
724	Bit8u hdcount, hdidmap[BX_MAX_ATA_DEVICES+BX_MAX_SCSI_DEVICES];
725	#else
726	Bit8u hdcount, hdidmap[BX_MAX_ATA_DEVICES];
727	#endif
728
729	// map between (bios cd id - 0xE0) and ata channels
730	Bit8u cdcount, cdidmap[BX_MAX_ATA_DEVICES];
731
732	// Buffer for DPTE table
733	dpte_t dpte;
734
735	// Count of transferred sectors and bytes
736	Bit16u trsfsectors;
737	Bit32u trsfbytes;
738
739	} ata_t;
740
741	#if BX_ELTORITO_BOOT
742	// ElTorito Device Emulation data
743	typedef struct {
744	Bit8u active;
745	Bit8u media;
746	Bit8u emulated_drive;
747	Bit8u controller_index;
748	Bit16u device_spec;
749	Bit32u ilba;
750	Bit16u buffer_segment;
751	Bit16u load_segment;
752	Bit16u sector_count;
753
754	// Virtual device
755	chs_t vdevice;
756	} cdemu_t;
757	#endif // BX_ELTORITO_BOOT
758
759	#ifdef VBOX_WITH_SCSI
760	typedef struct {
761	// I/O port this device is attached to.
762	Bit16u io_base;
763	// Target Id.
764	Bit8u target_id;
765	// SCSI devices info
766	ata_device_t device_info;
767	} scsi_device_t;
768
769	typedef struct {
770	// SCSi device info
771	scsi_device_t devices[BX_MAX_SCSI_DEVICES];
772	// Number of scsi disks.
773	Bit8u hdcount;
774	} scsi_t;
775	#endif
776
777	// for access to EBDA area
778	// The EBDA structure should conform to
779	// http://www.frontiernet.net/~fys/rombios.htm document
780	// I made the ata and cdemu structs begin at 0x121 in the EBDA seg
781	typedef struct {
782	unsigned char filler1[0x3D];
783
784	// FDPT - Can be splitted in data members if needed
785	unsigned char fdpt0[0x10];
786	unsigned char fdpt1[0x10];
787
788	unsigned char filler2[0xC4];
789
790	// ATA Driver data
791	ata_t ata;
792
793	#if BX_ELTORITO_BOOT
794	// El Torito Emulation data
795	cdemu_t cdemu;
796	#endif // BX_ELTORITO_BOOT
797
798	#ifdef VBOX
799
800	#ifdef VBOX_WITH_SCSI
801	// SCSI Driver data
802	scsi_t scsi;
803	# endif
804
805	unsigned char uForceBootDrive;
806	unsigned char uForceBootDevice;
807	#endif /* VBOX */
808
809	} ebda_data_t;
810
811	#ifdef VBOX
812	// the last 16 bytes of the EBDA segment are used for the MPS floating
813	// pointer structure (only if an IOAPIC is present)
814	#endif
815
816	#define EbdaData ((ebda_data_t *) 0)
817
818	// for access to the int13ext structure
819	typedef struct {
820	Bit8u size;
821	Bit8u reserved;
822	Bit16u count;
823	Bit16u offset;
824	Bit16u segment;
825	Bit32u lba1;
826	Bit32u lba2;
827	} int13ext_t;
828
829	#define Int13Ext ((int13ext_t *) 0)
830
831	// Disk Physical Table definition
832	typedef struct {
833	Bit16u size;
834	Bit16u infos;
835	Bit32u cylinders;
836	Bit32u heads;
837	Bit32u spt;
838	Bit32u sector_count1;
839	Bit32u sector_count2;
840	Bit16u blksize;
841	Bit16u dpte_offset;
842	Bit16u dpte_segment;
843	Bit16u key;
844	Bit8u dpi_length;
845	Bit8u reserved1;
846	Bit16u reserved2;
847	Bit8u host_bus[4];
848	Bit8u iface_type[8];
849	Bit8u iface_path[8];
850	Bit8u device_path[8];
851	Bit8u reserved3;
852	Bit8u checksum;
853	} dpt_t;
854
855	#define Int13DPT ((dpt_t *) 0)
856
857	#endif // BX_USE_ATADRV
858
859	typedef struct {
860	union {
861	struct {
862	Bit16u di, si, bp, sp;
863	Bit16u bx, dx, cx, ax;
864	} r16;
865	struct {
866	Bit16u filler[4];
867	Bit8u bl, bh, dl, dh, cl, ch, al, ah;
868	} r8;
869	} u;
870	} pusha_regs_t;
871
872	typedef struct {
873	union {
874	struct {
875	Bit32u edi, esi, ebp, esp;
876	Bit32u ebx, edx, ecx, eax;
877	} r32;
878	struct {
879	Bit16u di, filler1, si, filler2, bp, filler3, sp, filler4;
880	Bit16u bx, filler5, dx, filler6, cx, filler7, ax, filler8;
881	} r16;
882	struct {
883	Bit32u filler[4];
884	Bit8u bl, bh;
885	Bit16u filler1;
886	Bit8u dl, dh;
887	Bit16u filler2;
888	Bit8u cl, ch;
889	Bit16u filler3;
890	Bit8u al, ah;
891	Bit16u filler4;
892	} r8;
893	} u;
894	} pushad_regs_t;
895
896	typedef struct {
897	union {
898	struct {
899	Bit16u flags;
900	} r16;
901	struct {
902	Bit8u flagsl;
903	Bit8u flagsh;
904	} r8;
905	} u;
906	} flags_t;
907
908	#define SetCF(x) x.u.r8.flagsl \|= 0x01
909	#define SetZF(x) x.u.r8.flagsl \|= 0x40
910	#define ClearCF(x) x.u.r8.flagsl &= 0xfe
911	#define ClearZF(x) x.u.r8.flagsl &= 0xbf
912	#define GetCF(x) (x.u.r8.flagsl & 0x01)
913
914	typedef struct {
915	Bit16u ip;
916	Bit16u cs;
917	flags_t flags;
918	} iret_addr_t;
919
920
921
922	static Bit8u inb();
923	static Bit8u inb_cmos();
924	static void outb();
925	static void outb_cmos();
926	static Bit16u inw();
927	static void outw();
928	static void init_rtc();
929	static bx_bool rtc_updating();
930
931	static Bit8u read_byte();
932	static Bit16u read_word();
933	static void write_byte();
934	static void write_word();
935	static void bios_printf();
936
937	static Bit8u send_to_mouse_ctrl();
938	static Bit8u get_mouse_data();
939	static void set_kbd_command_byte();
940
941	static void int09_function();
942	static void int13_harddisk();
943	static void int13_cdrom();
944	static void int13_cdemu();
945	static void int13_eltorito();
946	static void int13_diskette_function();
947	static void int14_function();
948	static void int15_function();
949	static void int16_function();
950	static void int17_function();
951	static Bit32u int19_function();
952	static void int1a_function();
953	static void int70_function();
954	static void int74_function();
955	static void dummy_isr_function();
956	static Bit16u get_CS();
957	static Bit16u get_SS();
958	static unsigned int enqueue_key();
959	static unsigned int dequeue_key();
960	static void get_hd_geometry();
961	static void set_diskette_ret_status();
962	static void set_diskette_current_cyl();
963	static void determine_floppy_media();
964	static bx_bool floppy_drive_exists();
965	static bx_bool floppy_drive_recal();
966	static bx_bool floppy_media_known();
967	static bx_bool floppy_media_sense();
968	static bx_bool set_enable_a20();
969	static void debugger_on();
970	static void debugger_off();
971	static void keyboard_init();
972	static void keyboard_panic();
973	static void shutdown_status_panic();
974	static void nmi_handler_msg();
975
976	static void print_bios_banner();
977	static void print_boot_device();
978	static void print_boot_failure();
979	static void print_cdromboot_failure();
980
981	# if BX_USE_ATADRV
982
983	// ATA / ATAPI driver
984	void ata_init();
985	void ata_detect();
986	void ata_reset();
987
988	Bit16u ata_cmd_non_data();
989	Bit16u ata_cmd_data_in();
990	Bit16u ata_cmd_data_out();
991	Bit16u ata_cmd_packet();
992
993	Bit16u atapi_get_sense();
994	Bit16u atapi_is_ready();
995	Bit16u atapi_is_cdrom();
996
997	#endif // BX_USE_ATADRV
998
999	#if BX_ELTORITO_BOOT
1000
1001	void cdemu_init();
1002	Bit8u cdemu_isactive();
1003	Bit8u cdemu_emulated_drive();
1004
1005	Bit16u cdrom_boot();
1006
1007	#endif // BX_ELTORITO_BOOT
1008
1009	#ifdef VBOX
1010	static char bios_prefix_string[] = "BIOS: ";
1011	/* Do not use build timestamps in this string. Otherwise even rebuilding the
1012	* very same code will lead to compare errors when restoring saved state. */
1013	static char bios_cvs_version_string[] = "VirtualBox " VBOX_VERSION_STRING;
1014	#define BIOS_COPYRIGHT_STRING "Sun xVM VirtualBox BIOS"
1015	#else /* !VBOX */
1016	static char bios_cvs_version_string[] = "$Revision: 1.176 $ $Date: 2006/12/30 17:13:17 $";
1017
1018	#define BIOS_COPYRIGHT_STRING "(c) 2002 MandrakeSoft S.A. Written by Kevin Lawton & the Bochs team."
1019	#endif /* !VBOX */
1020
1021	#define BIOS_PRINTF_HALT 1
1022	#define BIOS_PRINTF_SCREEN 2
1023	#define BIOS_PRINTF_INFO 4
1024	#define BIOS_PRINTF_DEBUG 8
1025	#define BIOS_PRINTF_ALL (BIOS_PRINTF_SCREEN \| BIOS_PRINTF_INFO)
1026	#define BIOS_PRINTF_DEBHALT (BIOS_PRINTF_SCREEN \| BIOS_PRINTF_INFO \| BIOS_PRINTF_HALT)
1027
1028	#define printf(format, p...) bios_printf(BIOS_PRINTF_SCREEN, format, ##p)
1029
1030	// Defines the output macros.
1031	// BX_DEBUG goes to INFO port until we can easily choose debug info on a
1032	// per-device basis. Debug info are sent only in debug mode
1033	#if DEBUG_ROMBIOS
1034	# define BX_DEBUG(format, p...) bios_printf(BIOS_PRINTF_INFO, format, ##p)
1035	#else
1036	# define BX_DEBUG(format, p...)
1037	#endif
1038	#ifdef VBOX
1039	#define BX_INFO(format, p...) do { put_str(BIOS_PRINTF_INFO, bios_prefix_string); bios_printf(BIOS_PRINTF_INFO, format, ##p); } while (0)
1040	#else /* !VBOX */
1041	#define BX_INFO(format, p...) bios_printf(BIOS_PRINTF_INFO, format, ##p)
1042	#endif /* !VBOX */
1043	#define BX_PANIC(format, p...) bios_printf(BIOS_PRINTF_DEBHALT, format, ##p)
1044
1045	#if DEBUG_ATA
1046	# define BX_DEBUG_ATA(a...) BX_DEBUG(a)
1047	#else
1048	# define BX_DEBUG_ATA(a...)
1049	#endif
1050	#if DEBUG_INT13_HD
1051	# define BX_DEBUG_INT13_HD(a...) BX_DEBUG(a)
1052	#else
1053	# define BX_DEBUG_INT13_HD(a...)
1054	#endif
1055	#if DEBUG_INT13_CD
1056	# define BX_DEBUG_INT13_CD(a...) BX_DEBUG(a)
1057	#else
1058	# define BX_DEBUG_INT13_CD(a...)
1059	#endif
1060	#if DEBUG_INT13_ET
1061	# define BX_DEBUG_INT13_ET(a...) BX_DEBUG(a)
1062	#else
1063	# define BX_DEBUG_INT13_ET(a...)
1064	#endif
1065	#if DEBUG_INT13_FL
1066	# define BX_DEBUG_INT13_FL(a...) BX_DEBUG(a)
1067	#else
1068	# define BX_DEBUG_INT13_FL(a...)
1069	#endif
1070	#if DEBUG_INT15
1071	# define BX_DEBUG_INT15(a...) BX_DEBUG(a)
1072	#else
1073	# define BX_DEBUG_INT15(a...)
1074	#endif
1075	#if DEBUG_INT16
1076	# define BX_DEBUG_INT16(a...) BX_DEBUG(a)
1077	#else
1078	# define BX_DEBUG_INT16(a...)
1079	#endif
1080	#if DEBUG_INT1A
1081	# define BX_DEBUG_INT1A(a...) BX_DEBUG(a)
1082	#else
1083	# define BX_DEBUG_INT1A(a...)
1084	#endif
1085	#if DEBUG_INT74
1086	# define BX_DEBUG_INT74(a...) BX_DEBUG(a)
1087	#else
1088	# define BX_DEBUG_INT74(a...)
1089	#endif
1090
1091	#define SET_AL(val8) AX = ((AX & 0xff00) \| (val8))
1092	#define SET_BL(val8) BX = ((BX & 0xff00) \| (val8))
1093	#define SET_CL(val8) CX = ((CX & 0xff00) \| (val8))
1094	#define SET_DL(val8) DX = ((DX & 0xff00) \| (val8))
1095	#define SET_AH(val8) AX = ((AX & 0x00ff) \| ((val8) << 8))
1096	#define SET_BH(val8) BX = ((BX & 0x00ff) \| ((val8) << 8))
1097	#define SET_CH(val8) CX = ((CX & 0x00ff) \| ((val8) << 8))
1098	#define SET_DH(val8) DX = ((DX & 0x00ff) \| ((val8) << 8))
1099
1100	#define GET_AL() ( AX & 0x00ff )
1101	#define GET_BL() ( BX & 0x00ff )
1102	#define GET_CL() ( CX & 0x00ff )
1103	#define GET_DL() ( DX & 0x00ff )
1104	#define GET_AH() ( AX >> 8 )
1105	#define GET_BH() ( BX >> 8 )
1106	#define GET_CH() ( CX >> 8 )
1107	#define GET_DH() ( DX >> 8 )
1108
1109	#define GET_ELDL() ( ELDX & 0x00ff )
1110	#define GET_ELDH() ( ELDX >> 8 )
1111
1112	#define SET_CF() FLAGS \|= 0x0001
1113	#define CLEAR_CF() FLAGS &= 0xfffe
1114	#define GET_CF() (FLAGS & 0x0001)
1115
1116	#define SET_ZF() FLAGS \|= 0x0040
1117	#define CLEAR_ZF() FLAGS &= 0xffbf
1118	#define GET_ZF() (FLAGS & 0x0040)
1119
1120	#define UNSUPPORTED_FUNCTION 0x86
1121
1122	#define none 0
1123	#define MAX_SCAN_CODE 0x58
1124
1125	static struct {
1126	Bit16u normal;
1127	Bit16u shift;
1128	Bit16u control;
1129	Bit16u alt;
1130	Bit8u lock_flags;
1131	} scan_to_scanascii[MAX_SCAN_CODE + 1] = {
1132	{ none, none, none, none, none },
1133	{ 0x011b, 0x011b, 0x011b, 0x0100, none }, /* escape */
1134	{ 0x0231, 0x0221, none, 0x7800, none }, /* 1! */
1135	{ 0x0332, 0x0340, 0x0300, 0x7900, none }, /* 2@ */
1136	{ 0x0433, 0x0423, none, 0x7a00, none }, /* 3# */
1137	{ 0x0534, 0x0524, none, 0x7b00, none }, /* 4$ */
1138	{ 0x0635, 0x0625, none, 0x7c00, none }, /* 5% */
1139	{ 0x0736, 0x075e, 0x071e, 0x7d00, none }, /* 6^ */
1140	{ 0x0837, 0x0826, none, 0x7e00, none }, /* 7& */
1141	{ 0x0938, 0x092a, none, 0x7f00, none }, /* 8* */
1142	{ 0x0a39, 0x0a28, none, 0x8000, none }, /* 9( */
1143	{ 0x0b30, 0x0b29, none, 0x8100, none }, /* 0) */
1144	{ 0x0c2d, 0x0c5f, 0x0c1f, 0x8200, none }, /* -_ */
1145	{ 0x0d3d, 0x0d2b, none, 0x8300, none }, /* =+ */
1146	{ 0x0e08, 0x0e08, 0x0e7f, none, none }, /* backspace */
1147	{ 0x0f09, 0x0f00, none, none, none }, /* tab */
1148	{ 0x1071, 0x1051, 0x1011, 0x1000, 0x40 }, /* Q */
1149	{ 0x1177, 0x1157, 0x1117, 0x1100, 0x40 }, /* W */
1150	{ 0x1265, 0x1245, 0x1205, 0x1200, 0x40 }, /* E */
1151	{ 0x1372, 0x1352, 0x1312, 0x1300, 0x40 }, /* R */
1152	{ 0x1474, 0x1454, 0x1414, 0x1400, 0x40 }, /* T */
1153	{ 0x1579, 0x1559, 0x1519, 0x1500, 0x40 }, /* Y */
1154	{ 0x1675, 0x1655, 0x1615, 0x1600, 0x40 }, /* U */
1155	{ 0x1769, 0x1749, 0x1709, 0x1700, 0x40 }, /* I */
1156	{ 0x186f, 0x184f, 0x180f, 0x1800, 0x40 }, /* O */
1157	{ 0x1970, 0x1950, 0x1910, 0x1900, 0x40 }, /* P */
1158	{ 0x1a5b, 0x1a7b, 0x1a1b, none, none }, /* [{ */
1159	{ 0x1b5d, 0x1b7d, 0x1b1d, none, none }, /* ]} */
1160	{ 0x1c0d, 0x1c0d, 0x1c0a, none, none }, /* Enter */
1161	{ none, none, none, none, none }, /* L Ctrl */
1162	{ 0x1e61, 0x1e41, 0x1e01, 0x1e00, 0x40 }, /* A */
1163	{ 0x1f73, 0x1f53, 0x1f13, 0x1f00, 0x40 }, /* S */
1164	{ 0x2064, 0x2044, 0x2004, 0x2000, 0x40 }, /* D */
1165	{ 0x2166, 0x2146, 0x2106, 0x2100, 0x40 }, /* F */
1166	{ 0x2267, 0x2247, 0x2207, 0x2200, 0x40 }, /* G */
1167	{ 0x2368, 0x2348, 0x2308, 0x2300, 0x40 }, /* H */
1168	{ 0x246a, 0x244a, 0x240a, 0x2400, 0x40 }, /* J */
1169	{ 0x256b, 0x254b, 0x250b, 0x2500, 0x40 }, /* K */
1170	{ 0x266c, 0x264c, 0x260c, 0x2600, 0x40 }, /* L */
1171	{ 0x273b, 0x273a, none, none, none }, /* ;: */
1172	{ 0x2827, 0x2822, none, none, none }, /* '" */
1173	{ 0x2960, 0x297e, none, none, none }, /* `~ */
1174	{ none, none, none, none, none }, /* L shift */
1175	{ 0x2b5c, 0x2b7c, 0x2b1c, none, none }, /* \|\ */
1176	{ 0x2c7a, 0x2c5a, 0x2c1a, 0x2c00, 0x40 }, /* Z */
1177	{ 0x2d78, 0x2d58, 0x2d18, 0x2d00, 0x40 }, /* X */
1178	{ 0x2e63, 0x2e43, 0x2e03, 0x2e00, 0x40 }, /* C */
1179	{ 0x2f76, 0x2f56, 0x2f16, 0x2f00, 0x40 }, /* V */
1180	{ 0x3062, 0x3042, 0x3002, 0x3000, 0x40 }, /* B */
1181	{ 0x316e, 0x314e, 0x310e, 0x3100, 0x40 }, /* N */
1182	{ 0x326d, 0x324d, 0x320d, 0x3200, 0x40 }, /* M */
1183	{ 0x332c, 0x333c, none, none, none }, /* ,< */
1184	{ 0x342e, 0x343e, none, none, none }, /* .> */
1185	{ 0x352f, 0x353f, none, none, none }, /* /? */
1186	{ none, none, none, none, none }, /* R Shift */
1187	{ 0x372a, 0x372a, none, none, none }, /* * */
1188	{ none, none, none, none, none }, /* L Alt */
1189	{ 0x3920, 0x3920, 0x3920, 0x3920, none }, /* space */
1190	{ none, none, none, none, none }, /* caps lock */
1191	{ 0x3b00, 0x5400, 0x5e00, 0x6800, none }, /* F1 */
1192	{ 0x3c00, 0x5500, 0x5f00, 0x6900, none }, /* F2 */
1193	{ 0x3d00, 0x5600, 0x6000, 0x6a00, none }, /* F3 */
1194	{ 0x3e00, 0x5700, 0x6100, 0x6b00, none }, /* F4 */
1195	{ 0x3f00, 0x5800, 0x6200, 0x6c00, none }, /* F5 */
1196	{ 0x4000, 0x5900, 0x6300, 0x6d00, none }, /* F6 */
1197	{ 0x4100, 0x5a00, 0x6400, 0x6e00, none }, /* F7 */
1198	{ 0x4200, 0x5b00, 0x6500, 0x6f00, none }, /* F8 */
1199	{ 0x4300, 0x5c00, 0x6600, 0x7000, none }, /* F9 */
1200	{ 0x4400, 0x5d00, 0x6700, 0x7100, none }, /* F10 */
1201	{ none, none, none, none, none }, /* Num Lock */
1202	{ none, none, none, none, none }, /* Scroll Lock */
1203	{ 0x4700, 0x4737, 0x7700, none, 0x20 }, /* 7 Home */
1204	{ 0x4800, 0x4838, none, none, 0x20 }, /* 8 UP */
1205	{ 0x4900, 0x4939, 0x8400, none, 0x20 }, /* 9 PgUp */
1206	{ 0x4a2d, 0x4a2d, none, none, none }, /* - */
1207	{ 0x4b00, 0x4b34, 0x7300, none, 0x20 }, /* 4 Left */
1208	{ 0x4c00, 0x4c35, none, none, 0x20 }, /* 5 */
1209	{ 0x4d00, 0x4d36, 0x7400, none, 0x20 }, /* 6 Right */
1210	{ 0x4e2b, 0x4e2b, none, none, none }, /* + */
1211	{ 0x4f00, 0x4f31, 0x7500, none, 0x20 }, /* 1 End */
1212	{ 0x5000, 0x5032, none, none, 0x20 }, /* 2 Down */
1213	{ 0x5100, 0x5133, 0x7600, none, 0x20 }, /* 3 PgDn */
1214	{ 0x5200, 0x5230, none, none, 0x20 }, /* 0 Ins */
1215	{ 0x5300, 0x532e, none, none, 0x20 }, /* Del */
1216	{ none, none, none, none, none },
1217	{ none, none, none, none, none },
1218	{ 0x565c, 0x567c, none, none, none }, /* \\| */
1219	#ifndef VBOX
1220	{ 0x5700, 0x5700, none, none, none }, /* F11 */
1221	{ 0x5800, 0x5800, none, none, none } /* F12 */
1222	#else
1223	{ 0x8500, 0x8700, 0x8900, 0x8b00, none }, /* F11 */
1224	{ 0x8600, 0x8800, 0x8a00, 0x8c00, none } /* F12 */
1225	#endif
1226	};
1227
1228	Bit8u
1229	inb(port)
1230	Bit16u port;
1231	{
1232	ASM_START
1233	push bp
1234	mov bp, sp
1235
1236	push dx
1237	mov dx, 4[bp]
1238	in al, dx
1239	pop dx
1240
1241	pop bp
1242	ASM_END
1243	}
1244
1245	#if BX_USE_ATADRV
1246	Bit16u
1247	inw(port)
1248	Bit16u port;
1249	{
1250	ASM_START
1251	push bp
1252	mov bp, sp
1253
1254	push dx
1255	mov dx, 4[bp]
1256	in ax, dx
1257	pop dx
1258
1259	pop bp
1260	ASM_END
1261	}
1262	#endif
1263
1264	void
1265	outb(port, val)
1266	Bit16u port;
1267	Bit8u val;
1268	{
1269	ASM_START
1270	push bp
1271	mov bp, sp
1272
1273	push ax
1274	push dx
1275	mov dx, 4[bp]
1276	mov al, 6[bp]
1277	out dx, al
1278	pop dx
1279	pop ax
1280
1281	pop bp
1282	ASM_END
1283	}
1284
1285	#if BX_USE_ATADRV
1286	void
1287	outw(port, val)
1288	Bit16u port;
1289	Bit16u val;
1290	{
1291	ASM_START
1292	push bp
1293	mov bp, sp
1294
1295	push ax
1296	push dx
1297	mov dx, 4[bp]
1298	mov ax, 6[bp]
1299	out dx, ax
1300	pop dx
1301	pop ax
1302
1303	pop bp
1304	ASM_END
1305	}
1306	#endif
1307
1308	void
1309	outb_cmos(cmos_reg, val)
1310	Bit8u cmos_reg;
1311	Bit8u val;
1312	{
1313	ASM_START
1314	push bp
1315	mov bp, sp
1316
1317	mov al, 4[bp] ;; cmos_reg
1318	out 0x70, al
1319	mov al, 6[bp] ;; val
1320	out 0x71, al
1321
1322	pop bp
1323	ASM_END
1324	}
1325
1326	Bit8u
1327	inb_cmos(cmos_reg)
1328	Bit8u cmos_reg;
1329	{
1330	ASM_START
1331	push bp
1332	mov bp, sp
1333
1334	mov al, 4[bp] ;; cmos_reg
1335	out 0x70, al
1336	in al, 0x71
1337
1338	pop bp
1339	ASM_END
1340	}
1341
1342	void
1343	init_rtc()
1344	{
1345	outb_cmos(0x0a, 0x26);
1346	outb_cmos(0x0b, 0x02);
1347	inb_cmos(0x0c);
1348	inb_cmos(0x0d);
1349	}
1350
1351	bx_bool
1352	rtc_updating()
1353	{
1354	// This function checks to see if the update-in-progress bit
1355	// is set in CMOS Status Register A. If not, it returns 0.
1356	// If it is set, it tries to wait until there is a transition
1357	// to 0, and will return 0 if such a transition occurs. A 1
1358	// is returned only after timing out. The maximum period
1359	// that this bit should be set is constrained to 244useconds.
1360	// The count I use below guarantees coverage or more than
1361	// this time, with any reasonable IPS setting.
1362
1363	Bit16u count;
1364
1365	count = 25000;
1366	while (--count != 0) {
1367	if ( (inb_cmos(0x0a) & 0x80) == 0 )
1368	return(0);
1369	}
1370	return(1); // update-in-progress never transitioned to 0
1371	}
1372
1373
1374	Bit8u
1375	read_byte(seg, offset)
1376	Bit16u seg;
1377	Bit16u offset;
1378	{
1379	ASM_START
1380	push bp
1381	mov bp, sp
1382
1383	push bx
1384	push ds
1385	mov ax, 4[bp] ; segment
1386	mov ds, ax
1387	mov bx, 6[bp] ; offset
1388	mov al, [bx]
1389	;; al = return value (byte)
1390	pop ds
1391	pop bx
1392
1393	pop bp
1394	ASM_END
1395	}
1396
1397	Bit16u
1398	read_word(seg, offset)
1399	Bit16u seg;
1400	Bit16u offset;
1401	{
1402	ASM_START
1403	push bp
1404	mov bp, sp
1405
1406	push bx
1407	push ds
1408	mov ax, 4[bp] ; segment
1409	mov ds, ax
1410	mov bx, 6[bp] ; offset
1411	mov ax, [bx]
1412	;; ax = return value (word)
1413	pop ds
1414	pop bx
1415
1416	pop bp
1417	ASM_END
1418	}
1419
1420	void
1421	write_byte(seg, offset, data)
1422	Bit16u seg;
1423	Bit16u offset;
1424	Bit8u data;
1425	{
1426	ASM_START
1427	push bp
1428	mov bp, sp
1429
1430	push ax
1431	push bx
1432	push ds
1433	mov ax, 4[bp] ; segment
1434	mov ds, ax
1435	mov bx, 6[bp] ; offset
1436	mov al, 8[bp] ; data byte
1437	mov [bx], al ; write data byte
1438	pop ds
1439	pop bx
1440	pop ax
1441
1442	pop bp
1443	ASM_END
1444	}
1445
1446	void
1447	write_word(seg, offset, data)
1448	Bit16u seg;
1449	Bit16u offset;
1450	Bit16u data;
1451	{
1452	ASM_START
1453	push bp
1454	mov bp, sp
1455
1456	push ax
1457	push bx
1458	push ds
1459	mov ax, 4[bp] ; segment
1460	mov ds, ax
1461	mov bx, 6[bp] ; offset
1462	mov ax, 8[bp] ; data word
1463	mov [bx], ax ; write data word
1464	pop ds
1465	pop bx
1466	pop ax
1467
1468	pop bp
1469	ASM_END
1470	}
1471
1472	Bit16u
1473	get_CS()
1474	{
1475	ASM_START
1476	mov ax, cs
1477	ASM_END
1478	}
1479
1480	Bit16u
1481	get_SS()
1482	{
1483	ASM_START
1484	mov ax, ss
1485	ASM_END
1486	}
1487
1488	#if BX_DEBUG_SERIAL
1489	/* serial debug port*/
1490	#define BX_DEBUG_PORT 0x03f8
1491
1492	/* data */
1493	#define UART_RBR 0x00
1494	#define UART_THR 0x00
1495
1496	/* control */
1497	#define UART_IER 0x01
1498	#define UART_IIR 0x02
1499	#define UART_FCR 0x02
1500	#define UART_LCR 0x03
1501	#define UART_MCR 0x04
1502	#define UART_DLL 0x00
1503	#define UART_DLM 0x01
1504
1505	/* status */
1506	#define UART_LSR 0x05
1507	#define UART_MSR 0x06
1508	#define UART_SCR 0x07
1509
1510	int uart_can_tx_byte(base_port)
1511	Bit16u base_port;
1512	{
1513	return inb(base_port + UART_LSR) & 0x20;
1514	}
1515
1516	void uart_wait_to_tx_byte(base_port)
1517	Bit16u base_port;
1518	{
1519	while (!uart_can_tx_byte(base_port));
1520	}
1521
1522	void uart_wait_until_sent(base_port)
1523	Bit16u base_port;
1524	{
1525	while (!(inb(base_port + UART_LSR) & 0x40));
1526	}
1527
1528	void uart_tx_byte(base_port, data)
1529	Bit16u base_port;
1530	Bit8u data;
1531	{
1532	uart_wait_to_tx_byte(base_port);
1533	outb(base_port + UART_THR, data);
1534	uart_wait_until_sent(base_port);
1535	}
1536	#endif
1537
1538	void
1539	wrch(c)
1540	Bit8u c;
1541	{
1542	ASM_START
1543	push bp
1544	mov bp, sp
1545
1546	push bx
1547	mov ah, #0x0e
1548	mov al, 4[bp]
1549	xor bx,bx
1550	int #0x10
1551	pop bx
1552
1553	pop bp
1554	ASM_END
1555	}
1556
1557	void
1558	send(action, c)
1559	Bit16u action;
1560	Bit8u c;
1561	{
1562	#if BX_DEBUG_SERIAL
1563	if (c == '\n') uart_tx_byte(BX_DEBUG_PORT, '\r');
1564	uart_tx_byte(BX_DEBUG_PORT, c);
1565	#endif
1566	#if BX_VIRTUAL_PORTS
1567	if (action & BIOS_PRINTF_DEBUG) outb(DEBUG_PORT, c);
1568	if (action & BIOS_PRINTF_INFO) outb(INFO_PORT, c);
1569	#endif
1570	if (action & BIOS_PRINTF_SCREEN) {
1571	if (c == '\n') wrch('\r');
1572	wrch(c);
1573	}
1574	}
1575
1576	void
1577	put_int(action, val, width, neg)
1578	Bit16u action;
1579	short val, width;
1580	bx_bool neg;
1581	{
1582	short nval = val / 10;
1583	if (nval)
1584	put_int(action, nval, width - 1, neg);
1585	else {
1586	while (--width > 0) send(action, ' ');
1587	if (neg) send(action, '-');
1588	}
1589	send(action, val - (nval * 10) + '0');
1590	}
1591
1592	void
1593	put_uint(action, val, width, neg)
1594	Bit16u action;
1595	unsigned short val;
1596	short width;
1597	bx_bool neg;
1598	{
1599	unsigned short nval = val / 10;
1600	if (nval)
1601	put_uint(action, nval, width - 1, neg);
1602	else {
1603	while (--width > 0) send(action, ' ');
1604	if (neg) send(action, '-');
1605	}
1606	send(action, val - (nval * 10) + '0');
1607	}
1608
1609	void
1610	put_luint(action, val, width, neg)
1611	Bit16u action;
1612	unsigned long val;
1613	short width;
1614	bx_bool neg;
1615	{
1616	unsigned long nval = val / 10;
1617	if (nval)
1618	put_luint(action, nval, width - 1, neg);
1619	else {
1620	while (--width > 0) send(action, ' ');
1621	if (neg) send(action, '-');
1622	}
1623	send(action, val - (nval * 10) + '0');
1624	}
1625
1626	#ifdef VBOX
1627	void put_str(action, s)
1628	Bit16u action;
1629	Bit8u *s;
1630	{
1631	Bit8u c;
1632	if (!s)
1633	s = "<NULL>";
1634
1635	while (c = read_byte(get_CS(), s)) {
1636	send(action, c);
1637	s++;
1638	}
1639	}
1640	#endif /* VBOX */
1641
1642	//--------------------------------------------------------------------------
1643	// bios_printf()
1644	// A compact variable argument printf function which prints its output via
1645	// an I/O port so that it can be logged by Bochs/Plex.
1646	// Currently, only %x is supported (or %02x, %04x, etc).
1647	//
1648	// Supports %[format_width][format]
1649	// where format can be d,x,c,s
1650	//--------------------------------------------------------------------------
1651	void
1652	bios_printf(action, s)
1653	Bit16u action;
1654	Bit8u *s;
1655	{
1656	Bit8u c, format_char;
1657	bx_bool in_format;
1658	short i;
1659	Bit16u *arg_ptr;
1660	Bit16u arg_seg, arg, nibble, hibyte, shift_count, format_width;
1661
1662	arg_ptr = &s;
1663	arg_seg = get_SS();
1664
1665	in_format = 0;
1666	format_width = 0;
1667
1668	if ((action & BIOS_PRINTF_DEBHALT) == BIOS_PRINTF_DEBHALT) {
1669	#if BX_VIRTUAL_PORTS
1670	outb(PANIC_PORT2, 0x00);
1671	#endif
1672	bios_printf (BIOS_PRINTF_SCREEN, "FATAL: ");
1673	}
1674
1675	while (c = read_byte(get_CS(), s)) {
1676	if ( c == '%' ) {
1677	in_format = 1;
1678	format_width = 0;
1679	}
1680	else if (in_format) {
1681	if ( (c>='0') && (c<='9') ) {
1682	format_width = (format_width * 10) + (c - '0');
1683	}
1684	else {
1685	arg_ptr++; // increment to next arg
1686	arg = read_word(arg_seg, arg_ptr);
1687	if (c == 'x') {
1688	if (format_width == 0)
1689	format_width = 4;
1690	for (i=format_width-1; i>=0; i--) {
1691	nibble = (arg >> (4 * i)) & 0x000f;
1692	send (action, (nibble<=9)? (nibble+'0') : (nibble-10+'A'));
1693	}
1694	}
1695	else if (c == 'u') {
1696	put_uint(action, arg, format_width, 0);
1697	}
1698	else if (c == 'l') {
1699	s++;
1700	arg_ptr++; /* increment to next arg */
1701	hibyte = read_word(arg_seg, arg_ptr);
1702	put_luint(action, ((Bit32u) hibyte << 16) \| arg, format_width, 0);
1703	}
1704	else if (c == 'd') {
1705	if (arg & 0x8000)
1706	put_int(action, -arg, format_width - 1, 1);
1707	else
1708	put_int(action, arg, format_width, 0);
1709	}
1710	else if (c == 's') {
1711	#ifndef VBOX
1712	bios_printf(action & (~BIOS_PRINTF_HALT), arg);
1713	#else /* VBOX */
1714	put_str(action, arg);
1715	#endif /* VBOX */
1716	}
1717	else if (c == 'c') {
1718	send(action, arg);
1719	}
1720	else
1721	BX_PANIC("bios_printf: unknown format\n");
1722	in_format = 0;
1723	}
1724	}
1725	else {
1726	send(action, c);
1727	}
1728	s ++;
1729	}
1730
1731	if (action & BIOS_PRINTF_HALT) {
1732	// freeze in a busy loop.
1733	ASM_START
1734	cli
1735	halt2_loop:
1736	hlt
1737	jmp halt2_loop
1738	ASM_END
1739	}
1740	}
1741
1742	//--------------------------------------------------------------------------
1743	// keyboard_init
1744	//--------------------------------------------------------------------------
1745	// this file is based on LinuxBIOS implementation of keyboard.c
1746	// could convert to #asm to gain space
1747	void
1748	keyboard_init()
1749	{
1750	Bit16u max;
1751
1752	/* ------------------- Flush buffers ------------------------*/
1753	/* Wait until buffer is empty */
1754	max=0xffff;
1755	while ( (inb(0x64) & 0x02) && (--max>0)) outb(0x80, 0x00);
1756
1757	/* flush incoming keys */
1758	max=0x2000;
1759	while (--max > 0) {
1760	outb(0x80, 0x00);
1761	if (inb(0x64) & 0x01) {
1762	inb(0x60);
1763	max = 0x2000;
1764	}
1765	}
1766
1767	// Due to timer issues, and if the IPS setting is > 15000000,
1768	// the incoming keys might not be flushed here. That will
1769	// cause a panic a few lines below. See sourceforge bug report :
1770	// [ 642031 ] FATAL: Keyboard RESET error:993
1771
1772	/* ------------------- controller side ----------------------*/
1773	/* send cmd = 0xAA, self test 8042 */
1774	outb(0x64, 0xaa);
1775
1776	/* Wait until buffer is empty */
1777	max=0xffff;
1778	while ( (inb(0x64) & 0x02) && (--max>0)) outb(0x80, 0x00);
1779	if (max==0x0) keyboard_panic(00);
1780
1781	/* Wait for data */
1782	max=0xffff;
1783	while ( ((inb(0x64) & 0x01) == 0) && (--max>0) ) outb(0x80, 0x01);
1784	if (max==0x0) keyboard_panic(01);
1785
1786	/* read self-test result, 0x55 should be returned from 0x60 */
1787	if ((inb(0x60) != 0x55)){
1788	keyboard_panic(991);
1789	}
1790
1791	/* send cmd = 0xAB, keyboard interface test */
1792	outb(0x64,0xab);
1793
1794	/* Wait until buffer is empty */
1795	max=0xffff;
1796	while ((inb(0x64) & 0x02) && (--max>0)) outb(0x80, 0x10);
1797	if (max==0x0) keyboard_panic(10);
1798
1799	/* Wait for data */
1800	max=0xffff;
1801	while ( ((inb(0x64) & 0x01) == 0) && (--max>0) ) outb(0x80, 0x11);
1802	if (max==0x0) keyboard_panic(11);
1803
1804	/* read keyboard interface test result, */
1805	/* 0x00 should be returned form 0x60 */
1806	if ((inb(0x60) != 0x00)) {
1807	keyboard_panic(992);
1808	}
1809
1810	/* Enable Keyboard clock */
1811	outb(0x64,0xae);
1812	outb(0x64,0xa8);
1813
1814	/* ------------------- keyboard side ------------------------*/
1815	/* reset kerboard and self test (keyboard side) */
1816	outb(0x60, 0xff);
1817
1818	/* Wait until buffer is empty */
1819	max=0xffff;
1820	while ((inb(0x64) & 0x02) && (--max>0)) outb(0x80, 0x20);
1821	if (max==0x0) keyboard_panic(20);
1822
1823	/* Wait for data */
1824	max=0xffff;
1825	while ( ((inb(0x64) & 0x01) == 0) && (--max>0) ) outb(0x80, 0x21);
1826	if (max==0x0) keyboard_panic(21);
1827
1828	/* keyboard should return ACK */
1829	if ((inb(0x60) != 0xfa)) {
1830	keyboard_panic(993);
1831	}
1832
1833	/* Wait for data */
1834	max=0xffff;
1835	while ( ((inb(0x64) & 0x01) == 0) && (--max>0) ) outb(0x80, 0x31);
1836	if (max==0x0) keyboard_panic(31);
1837
1838	if ((inb(0x60) != 0xaa)) {
1839	keyboard_panic(994);
1840	}
1841
1842	/* Disable keyboard */
1843	outb(0x60, 0xf5);
1844
1845	/* Wait until buffer is empty */
1846	max=0xffff;
1847	while ((inb(0x64) & 0x02) && (--max>0)) outb(0x80, 0x40);
1848	if (max==0x0) keyboard_panic(40);
1849
1850	/* Wait for data */
1851	max=0xffff;
1852	while ( ((inb(0x64) & 0x01) == 0) && (--max>0) ) outb(0x80, 0x41);
1853	if (max==0x0) keyboard_panic(41);
1854
1855	/* keyboard should return ACK */
1856	if ((inb(0x60) != 0xfa)) {
1857	keyboard_panic(995);
1858	}
1859
1860	/* Write Keyboard Mode */
1861	outb(0x64, 0x60);
1862
1863	/* Wait until buffer is empty */
1864	max=0xffff;
1865	while ((inb(0x64) & 0x02) && (--max>0)) outb(0x80, 0x50);
1866	if (max==0x0) keyboard_panic(50);
1867
1868	/* send cmd: scan code convert, disable mouse, enable IRQ 1 */
1869	outb(0x60, 0x65);
1870
1871	/* Wait until buffer is empty */
1872	max=0xffff;
1873	while ((inb(0x64) & 0x02) && (--max>0)) outb(0x80, 0x60);
1874	if (max==0x0) keyboard_panic(60);
1875
1876	/* Enable keyboard */
1877	outb(0x60, 0xf4);
1878
1879	/* Wait until buffer is empty */
1880	max=0xffff;
1881	while ((inb(0x64) & 0x02) && (--max>0)) outb(0x80, 0x70);
1882	if (max==0x0) keyboard_panic(70);
1883
1884	/* Wait for data */
1885	max=0xffff;
1886	while ( ((inb(0x64) & 0x01) == 0) && (--max>0) ) outb(0x80, 0x71);
1887	if (max==0x0) keyboard_panic(70);
1888
1889	/* keyboard should return ACK */
1890	if ((inb(0x60) != 0xfa)) {
1891	keyboard_panic(996);
1892	}
1893
1894	outb(0x80, 0x77);
1895	}
1896
1897	//--------------------------------------------------------------------------
1898	// keyboard_panic
1899	//--------------------------------------------------------------------------
1900	void
1901	keyboard_panic(status)
1902	Bit16u status;
1903	{
1904	// If you're getting a 993 keyboard panic here,
1905	// please see the comment in keyboard_init
1906
1907	BX_PANIC("Keyboard error:%u\n",status);
1908	}
1909
1910	//--------------------------------------------------------------------------
1911	// shutdown_status_panic
1912	// called when the shutdown statsu is not implemented, displays the status
1913	//--------------------------------------------------------------------------
1914	void
1915	shutdown_status_panic(status)
1916	Bit16u status;
1917	{
1918	BX_PANIC("Unimplemented shutdown status: %02x\n",(Bit8u)status);
1919	}
1920
1921	#ifdef VBOX
1922	#include "logo.c"
1923	#endif /* VBOX */
1924
1925	//--------------------------------------------------------------------------
1926	// print_bios_banner
1927	// displays a the bios version
1928	//--------------------------------------------------------------------------
1929	void
1930	print_bios_banner()
1931	{
1932	#ifdef VBOX
1933	// Skip the logo if a warm boot is requested.
1934	Bit16u warm_boot = read_word(0x0040,0x0072);
1935	write_word(0x0040,0x0072, 0);
1936	if (warm_boot == 0x1234)
1937	return;
1938	#if !defined(DEBUG) \|\| defined(DEBUG_sunlover)
1939	/* show graphical logo */
1940	show_logo();
1941	#else
1942	/* set text mode */
1943	ASM_START
1944	mov ax, #0x0003
1945	int #0x10
1946	ASM_END
1947	#endif /* !DEBUG */
1948	#else /* !VBOX */
1949	printf(BX_APPNAME" BIOS - build: %s\n%s\nOptions: ",
1950	BIOS_BUILD_DATE, bios_cvs_version_string);
1951	printf(
1952	#if BX_APM
1953	"apmbios "
1954	#endif
1955	#if BX_PCIBIOS
1956	"pcibios "
1957	#endif
1958	#if BX_ELTORITO_BOOT
1959	"eltorito "
1960	#endif
1961	#if BX_ROMBIOS32
1962	"rombios32 "
1963	#endif
1964	"\n\n");
1965	#endif /* VBOX */
1966	}
1967
1968	//--------------------------------------------------------------------------
1969	// print_boot_device
1970	// displays the boot device
1971	//--------------------------------------------------------------------------
1972
1973	#ifdef VBOX
1974	static char drivetypes[][10]={"Floppy","Hard Disk","CD-ROM","LAN"};
1975	#else /* !VBOX */
1976	static char drivetypes[][10]={"Floppy","Hard Disk","CD-Rom"};
1977	#endif /* !VBOX */
1978
1979	#ifdef VBOX
1980	void
1981	print_boot_device(cdboot, lanboot, drive)
1982	Bit8u cdboot; Bit8u lanboot; Bit16u drive;
1983	#else /* !VBOX */
1984	void
1985	print_boot_device(cdboot, drive)
1986	Bit8u cdboot; Bit16u drive;
1987	#endif /* !VBOX */
1988	{
1989	Bit8u i;
1990
1991	#ifdef VBOX
1992	// cdboot contains 0 if lan/floppy/harddisk, 1 otherwise
1993	// lanboot contains 0 if floppy/harddisk, 1 otherwise
1994	#else /* !VBOX */
1995	// cdboot contains 0 if floppy/harddisk, 1 otherwise
1996	#endif /* !VBOX */
1997	// drive contains real/emulated boot drive
1998
1999	if(cdboot)i=2; // CD-Rom
2000	#ifdef VBOX
2001	else if(lanboot)i=3; // LAN
2002	#endif /* VBOX */
2003	else if((drive&0x0080)==0x00)i=0; // Floppy
2004	else if((drive&0x0080)==0x80)i=1; // Hard drive
2005	else return;
2006
2007	#ifdef VBOX
2008	BX_INFO("Booting from %s...\n",drivetypes[i]);
2009	#else /* !VBOX */
2010	printf("Booting from %s...\n",drivetypes[i]);
2011	#endif /* !VBOX */
2012	}
2013
2014	//--------------------------------------------------------------------------
2015	// print_boot_failure
2016	// displays the reason why boot failed
2017	//--------------------------------------------------------------------------
2018	#ifdef VBOX
2019	void
2020	print_boot_failure(cdboot, lanboot, drive, reason, lastdrive)
2021	Bit8u cdboot; Bit8u lanboot; Bit8u drive; Bit8u reason; Bit8u lastdrive;
2022	#else /* !VBOX */
2023	void
2024	print_boot_failure(cdboot, drive, reason, lastdrive)
2025	Bit8u cdboot; Bit8u drive; Bit8u lastdrive;
2026	#endif /* !VBOX */
2027	{
2028	Bit16u drivenum = drive&0x7f;
2029
2030	// cdboot: 1 if boot from cd, 0 otherwise
2031	#ifdef VBOX
2032	// lanboot: 1 if boot from lan, 0 otherwise
2033	#endif /* VBOX */
2034	// drive : drive number
2035	// reason: 0 signature check failed, 1 read error
2036	// lastdrive: 1 boot drive is the last one in boot sequence
2037
2038	if (cdboot)
2039	#ifndef VBOX
2040	bios_printf(BIOS_PRINTF_INFO \| BIOS_PRINTF_SCREEN, "Boot from %s failed\n",drivetypes[2]);
2041	#else /* VBOX */
2042	BX_INFO("Boot from %s failed\n",drivetypes[2]);
2043	else if (lanboot)
2044	BX_INFO("Boot from %s failed\n",drivetypes[3]);
2045	#endif /* VBOX */
2046	else if (drive & 0x80)
2047	#ifndef VBOX
2048	bios_printf(BIOS_PRINTF_INFO \| BIOS_PRINTF_SCREEN, "Boot from %s %d failed\n", drivetypes[1],drivenum);
2049	#else /* VBOX */
2050	BX_INFO("Boot from %s %d failed\n", drivetypes[1],drivenum);
2051	#endif /* VBOX */
2052	else
2053	#ifndef VBOX
2054	bios_printf(BIOS_PRINTF_INFO \| BIOS_PRINTF_SCREEN, "Boot from %s %d failed\n", drivetypes[0],drivenum);
2055	#else /* VBOX */
2056	BX_INFO("Boot from %s %d failed\n", drivetypes[0],drivenum);
2057	#endif /* VBOX */
2058
2059	if (lastdrive==1) {
2060	if (reason==0)
2061	#ifndef VBOX
2062	BX_PANIC("Not a bootable disk\n");
2063	#else /* VBOX */
2064	BX_PANIC("No bootable medium found! System halted.\n");
2065	#endif /* VBOX */
2066	else
2067	#ifndef VBOX
2068	BX_PANIC("Could not read the boot disk\n");
2069	#else /* VBOX */
2070	BX_PANIC("Could not read from the boot medium! System halted.\n");
2071	#endif /* VBOX */
2072	}
2073	}
2074
2075	//--------------------------------------------------------------------------
2076	// print_cdromboot_failure
2077	// displays the reason why boot failed
2078	//--------------------------------------------------------------------------
2079	void
2080	print_cdromboot_failure( code )
2081	Bit16u code;
2082	{
2083	#ifndef VBOX
2084	bios_printf(BIOS_PRINTF_SCREEN \| BIOS_PRINTF_INFO, "CDROM boot failure code : %04x\n",code);
2085	#else /* VBOX */
2086	BX_INFO("CDROM boot failure code : %04x\n",code);
2087	#endif /* VBOX */
2088
2089	return;
2090	}
2091
2092	void
2093	nmi_handler_msg()
2094	{
2095	BX_PANIC("NMI Handler called\n");
2096	}
2097
2098	void
2099	int18_panic_msg()
2100	{
2101	BX_PANIC("INT18: BOOT FAILURE\n");
2102	}
2103
2104	void
2105	log_bios_start()
2106	{
2107	#if BX_DEBUG_SERIAL
2108	outb(BX_DEBUG_PORT+UART_LCR, 0x03); /* setup for serial logging: 8N1 */
2109	#endif
2110	BX_INFO("%s\n", bios_cvs_version_string);
2111	}
2112
2113	bx_bool
2114	set_enable_a20(val)
2115	bx_bool val;
2116	{
2117	Bit8u oldval;
2118
2119	// Use PS2 System Control port A to set A20 enable
2120
2121	// get current setting first
2122	oldval = inb(0x92);
2123
2124	// change A20 status
2125	if (val)
2126	outb(0x92, oldval \| 0x02);
2127	else
2128	outb(0x92, oldval & 0xfd);
2129
2130	return((oldval & 0x02) != 0);
2131	}
2132
2133	void
2134	debugger_on()
2135	{
2136	outb(0xfedc, 0x01);
2137	}
2138
2139	void
2140	debugger_off()
2141	{
2142	outb(0xfedc, 0x00);
2143	}
2144
2145	#if BX_USE_ATADRV
2146
2147	// ---------------------------------------------------------------------------
2148	// Start of ATA/ATAPI Driver
2149	// ---------------------------------------------------------------------------
2150
2151	// Global defines -- ATA register and register bits.
2152	// command block & control block regs
2153	#define ATA_CB_DATA 0 // data reg in/out pio_base_addr1+0
2154	#define ATA_CB_ERR 1 // error in pio_base_addr1+1
2155	#define ATA_CB_FR 1 // feature reg out pio_base_addr1+1
2156	#define ATA_CB_SC 2 // sector count in/out pio_base_addr1+2
2157	#define ATA_CB_SN 3 // sector number in/out pio_base_addr1+3
2158	#define ATA_CB_CL 4 // cylinder low in/out pio_base_addr1+4
2159	#define ATA_CB_CH 5 // cylinder high in/out pio_base_addr1+5
2160	#define ATA_CB_DH 6 // device head in/out pio_base_addr1+6
2161	#define ATA_CB_STAT 7 // primary status in pio_base_addr1+7
2162	#define ATA_CB_CMD 7 // command out pio_base_addr1+7
2163	#define ATA_CB_ASTAT 6 // alternate status in pio_base_addr2+6
2164	#define ATA_CB_DC 6 // device control out pio_base_addr2+6
2165	#define ATA_CB_DA 7 // device address in pio_base_addr2+7
2166
2167	#define ATA_CB_ER_ICRC 0x80 // ATA Ultra DMA bad CRC
2168	#define ATA_CB_ER_BBK 0x80 // ATA bad block
2169	#define ATA_CB_ER_UNC 0x40 // ATA uncorrected error
2170	#define ATA_CB_ER_MC 0x20 // ATA media change
2171	#define ATA_CB_ER_IDNF 0x10 // ATA id not found
2172	#define ATA_CB_ER_MCR 0x08 // ATA media change request
2173	#define ATA_CB_ER_ABRT 0x04 // ATA command aborted
2174	#define ATA_CB_ER_NTK0 0x02 // ATA track 0 not found
2175	#define ATA_CB_ER_NDAM 0x01 // ATA address mark not found
2176
2177	#define ATA_CB_ER_P_SNSKEY 0xf0 // ATAPI sense key (mask)
2178	#define ATA_CB_ER_P_MCR 0x08 // ATAPI Media Change Request
2179	#define ATA_CB_ER_P_ABRT 0x04 // ATAPI command abort
2180	#define ATA_CB_ER_P_EOM 0x02 // ATAPI End of Media
2181	#define ATA_CB_ER_P_ILI 0x01 // ATAPI Illegal Length Indication
2182
2183	// ATAPI Interrupt Reason bits in the Sector Count reg (CB_SC)
2184	#define ATA_CB_SC_P_TAG 0xf8 // ATAPI tag (mask)
2185	#define ATA_CB_SC_P_REL 0x04 // ATAPI release
2186	#define ATA_CB_SC_P_IO 0x02 // ATAPI I/O
2187	#define ATA_CB_SC_P_CD 0x01 // ATAPI C/D
2188
2189	// bits 7-4 of the device/head (CB_DH) reg
2190	#define ATA_CB_DH_DEV0 0xa0 // select device 0
2191	#define ATA_CB_DH_DEV1 0xb0 // select device 1
2192
2193	// status reg (CB_STAT and CB_ASTAT) bits
2194	#define ATA_CB_STAT_BSY 0x80 // busy
2195	#define ATA_CB_STAT_RDY 0x40 // ready
2196	#define ATA_CB_STAT_DF 0x20 // device fault
2197	#define ATA_CB_STAT_WFT 0x20 // write fault (old name)
2198	#define ATA_CB_STAT_SKC 0x10 // seek complete
2199	#define ATA_CB_STAT_SERV 0x10 // service
2200	#define ATA_CB_STAT_DRQ 0x08 // data request
2201	#define ATA_CB_STAT_CORR 0x04 // corrected
2202	#define ATA_CB_STAT_IDX 0x02 // index
2203	#define ATA_CB_STAT_ERR 0x01 // error (ATA)
2204	#define ATA_CB_STAT_CHK 0x01 // check (ATAPI)
2205
2206	// device control reg (CB_DC) bits
2207	#define ATA_CB_DC_HD15 0x08 // bit should always be set to one
2208	#define ATA_CB_DC_SRST 0x04 // soft reset
2209	#define ATA_CB_DC_NIEN 0x02 // disable interrupts
2210
2211	// Most mandtory and optional ATA commands (from ATA-3),
2212	#define ATA_CMD_CFA_ERASE_SECTORS 0xC0
2213	#define ATA_CMD_CFA_REQUEST_EXT_ERR_CODE 0x03
2214	#define ATA_CMD_CFA_TRANSLATE_SECTOR 0x87
2215	#define ATA_CMD_CFA_WRITE_MULTIPLE_WO_ERASE 0xCD
2216	#define ATA_CMD_CFA_WRITE_SECTORS_WO_ERASE 0x38
2217	#define ATA_CMD_CHECK_POWER_MODE1 0xE5
2218	#define ATA_CMD_CHECK_POWER_MODE2 0x98
2219	#define ATA_CMD_DEVICE_RESET 0x08
2220	#define ATA_CMD_EXECUTE_DEVICE_DIAGNOSTIC 0x90
2221	#define ATA_CMD_FLUSH_CACHE 0xE7
2222	#define ATA_CMD_FORMAT_TRACK 0x50
2223	#define ATA_CMD_IDENTIFY_DEVICE 0xEC
2224	#define ATA_CMD_IDENTIFY_DEVICE_PACKET 0xA1
2225	#define ATA_CMD_IDENTIFY_PACKET_DEVICE 0xA1
2226	#define ATA_CMD_IDLE1 0xE3
2227	#define ATA_CMD_IDLE2 0x97
2228	#define ATA_CMD_IDLE_IMMEDIATE1 0xE1
2229	#define ATA_CMD_IDLE_IMMEDIATE2 0x95
2230	#define ATA_CMD_INITIALIZE_DRIVE_PARAMETERS 0x91
2231	#define ATA_CMD_INITIALIZE_DEVICE_PARAMETERS 0x91
2232	#define ATA_CMD_NOP 0x00
2233	#define ATA_CMD_PACKET 0xA0
2234	#define ATA_CMD_READ_BUFFER 0xE4
2235	#define ATA_CMD_READ_DMA 0xC8
2236	#define ATA_CMD_READ_DMA_QUEUED 0xC7
2237	#define ATA_CMD_READ_MULTIPLE 0xC4
2238	#define ATA_CMD_READ_SECTORS 0x20
2239	#ifdef VBOX
2240	#define ATA_CMD_READ_SECTORS_EXT 0x24
2241	#endif /* VBOX */
2242	#define ATA_CMD_READ_VERIFY_SECTORS 0x40
2243	#define ATA_CMD_RECALIBRATE 0x10
2244	#define ATA_CMD_SEEK 0x70
2245	#define ATA_CMD_SET_FEATURES 0xEF
2246	#define ATA_CMD_SET_MULTIPLE_MODE 0xC6
2247	#define ATA_CMD_SLEEP1 0xE6
2248	#define ATA_CMD_SLEEP2 0x99
2249	#define ATA_CMD_STANDBY1 0xE2
2250	#define ATA_CMD_STANDBY2 0x96
2251	#define ATA_CMD_STANDBY_IMMEDIATE1 0xE0
2252	#define ATA_CMD_STANDBY_IMMEDIATE2 0x94
2253	#define ATA_CMD_WRITE_BUFFER 0xE8
2254	#define ATA_CMD_WRITE_DMA 0xCA
2255	#define ATA_CMD_WRITE_DMA_QUEUED 0xCC
2256	#define ATA_CMD_WRITE_MULTIPLE 0xC5
2257	#define ATA_CMD_WRITE_SECTORS 0x30
2258	#ifdef VBOX
2259	#define ATA_CMD_WRITE_SECTORS_EXT 0x34
2260	#endif /* VBOX */
2261	#define ATA_CMD_WRITE_VERIFY 0x3C
2262
2263	#define ATA_IFACE_NONE 0x00
2264	#define ATA_IFACE_ISA 0x00
2265	#define ATA_IFACE_PCI 0x01
2266
2267	#define ATA_TYPE_NONE 0x00
2268	#define ATA_TYPE_UNKNOWN 0x01
2269	#define ATA_TYPE_ATA 0x02
2270	#define ATA_TYPE_ATAPI 0x03
2271	#define ATA_TYPE_SCSI 0x04 // SCSI disk
2272
2273	#define ATA_DEVICE_NONE 0x00
2274	#define ATA_DEVICE_HD 0xFF
2275	#define ATA_DEVICE_CDROM 0x05
2276
2277	#define ATA_MODE_NONE 0x00
2278	#define ATA_MODE_PIO16 0x00
2279	#define ATA_MODE_PIO32 0x01
2280	#define ATA_MODE_ISADMA 0x02
2281	#define ATA_MODE_PCIDMA 0x03
2282	#define ATA_MODE_USEIRQ 0x10
2283
2284	#define ATA_TRANSLATION_NONE 0
2285	#define ATA_TRANSLATION_LBA 1
2286	#define ATA_TRANSLATION_LARGE 2
2287	#define ATA_TRANSLATION_RECHS 3
2288
2289	#define ATA_DATA_NO 0x00
2290	#define ATA_DATA_IN 0x01
2291	#define ATA_DATA_OUT 0x02
2292
2293	// ---------------------------------------------------------------------------
2294	// ATA/ATAPI driver : initialization
2295	// ---------------------------------------------------------------------------
2296	void ata_init( )
2297	{
2298	Bit16u ebda_seg=read_word(0x0040,0x000E);
2299	Bit8u channel, device;
2300
2301	// Channels info init.
2302	for (channel=0; channel<BX_MAX_ATA_INTERFACES; channel++) {
2303	write_byte(ebda_seg,&EbdaData->ata.channels[channel].iface,ATA_IFACE_NONE);
2304	write_word(ebda_seg,&EbdaData->ata.channels[channel].iobase1,0x0);
2305	write_word(ebda_seg,&EbdaData->ata.channels[channel].iobase2,0x0);
2306	write_byte(ebda_seg,&EbdaData->ata.channels[channel].irq,0);
2307	}
2308
2309	// Devices info init.
2310	for (device=0; device<BX_MAX_ATA_DEVICES; device++) {
2311	write_byte(ebda_seg,&EbdaData->ata.devices[device].type,ATA_TYPE_NONE);
2312	write_byte(ebda_seg,&EbdaData->ata.devices[device].device,ATA_DEVICE_NONE);
2313	write_byte(ebda_seg,&EbdaData->ata.devices[device].removable,0);
2314	write_byte(ebda_seg,&EbdaData->ata.devices[device].lock,0);
2315	write_byte(ebda_seg,&EbdaData->ata.devices[device].mode,ATA_MODE_NONE);
2316	write_word(ebda_seg,&EbdaData->ata.devices[device].blksize,0);
2317	write_byte(ebda_seg,&EbdaData->ata.devices[device].translation,ATA_TRANSLATION_NONE);
2318	write_word(ebda_seg,&EbdaData->ata.devices[device].lchs.heads,0);
2319	write_word(ebda_seg,&EbdaData->ata.devices[device].lchs.cylinders,0);
2320	write_word(ebda_seg,&EbdaData->ata.devices[device].lchs.spt,0);
2321	write_word(ebda_seg,&EbdaData->ata.devices[device].pchs.heads,0);
2322	write_word(ebda_seg,&EbdaData->ata.devices[device].pchs.cylinders,0);
2323	write_word(ebda_seg,&EbdaData->ata.devices[device].pchs.spt,0);
2324
2325	write_dword(ebda_seg,&EbdaData->ata.devices[device].sectors,0L);
2326	}
2327
2328	// hdidmap and cdidmap init.
2329	for (device=0; device<BX_MAX_ATA_DEVICES; device++) {
2330	write_byte(ebda_seg,&EbdaData->ata.hdidmap[device],BX_MAX_ATA_DEVICES);
2331	write_byte(ebda_seg,&EbdaData->ata.cdidmap[device],BX_MAX_ATA_DEVICES);
2332	}
2333
2334	write_byte(ebda_seg,&EbdaData->ata.hdcount,0);
2335	write_byte(ebda_seg,&EbdaData->ata.cdcount,0);
2336	}
2337
2338	// ---------------------------------------------------------------------------
2339	// ATA/ATAPI driver : device detection
2340	// ---------------------------------------------------------------------------
2341
2342	void ata_detect( )
2343	{
2344	Bit16u ebda_seg=read_word(0x0040,0x000E);
2345	Bit8u hdcount, cdcount, device, type;
2346	Bit8u buffer[0x0200];
2347
2348	#if BX_MAX_ATA_INTERFACES > 0
2349	write_byte(ebda_seg,&EbdaData->ata.channels[0].iface,ATA_IFACE_ISA);
2350	write_word(ebda_seg,&EbdaData->ata.channels[0].iobase1,0x1f0);
2351	write_word(ebda_seg,&EbdaData->ata.channels[0].iobase2,0x3f0);
2352	write_byte(ebda_seg,&EbdaData->ata.channels[0].irq,14);
2353	#endif
2354	#if BX_MAX_ATA_INTERFACES > 1
2355	write_byte(ebda_seg,&EbdaData->ata.channels[1].iface,ATA_IFACE_ISA);
2356	write_word(ebda_seg,&EbdaData->ata.channels[1].iobase1,0x170);
2357	write_word(ebda_seg,&EbdaData->ata.channels[1].iobase2,0x370);
2358	write_byte(ebda_seg,&EbdaData->ata.channels[1].irq,15);
2359	#endif
2360	#if BX_MAX_ATA_INTERFACES > 2
2361	write_byte(ebda_seg,&EbdaData->ata.channels[2].iface,ATA_IFACE_ISA);
2362	write_word(ebda_seg,&EbdaData->ata.channels[2].iobase1,0x1e8);
2363	write_word(ebda_seg,&EbdaData->ata.channels[2].iobase2,0x3e0);
2364	write_byte(ebda_seg,&EbdaData->ata.channels[2].irq,12);
2365	#endif
2366	#if BX_MAX_ATA_INTERFACES > 3
2367	write_byte(ebda_seg,&EbdaData->ata.channels[3].iface,ATA_IFACE_ISA);
2368	write_word(ebda_seg,&EbdaData->ata.channels[3].iobase1,0x168);
2369	write_word(ebda_seg,&EbdaData->ata.channels[3].iobase2,0x360);
2370	write_byte(ebda_seg,&EbdaData->ata.channels[3].irq,11);
2371	#endif
2372	#if BX_MAX_ATA_INTERFACES > 4
2373	#error Please fill the ATA interface informations
2374	#endif
2375
2376	// Device detection
2377	hdcount=cdcount=0;
2378
2379	for(device=0; device<BX_MAX_ATA_DEVICES; device++) {
2380	Bit16u iobase1, iobase2;
2381	Bit8u channel, slave, shift;
2382	Bit8u sc, sn, cl, ch, st;
2383
2384	channel = device / 2;
2385	slave = device % 2;
2386
2387	iobase1 =read_word(ebda_seg,&EbdaData->ata.channels[channel].iobase1);
2388	iobase2 =read_word(ebda_seg,&EbdaData->ata.channels[channel].iobase2);
2389
2390	// Disable interrupts
2391	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15 \| ATA_CB_DC_NIEN);
2392
2393	// Look for device
2394	outb(iobase1+ATA_CB_DH, slave ? ATA_CB_DH_DEV1 : ATA_CB_DH_DEV0);
2395	outb(iobase1+ATA_CB_SC, 0x55);
2396	outb(iobase1+ATA_CB_SN, 0xaa);
2397	outb(iobase1+ATA_CB_SC, 0xaa);
2398	outb(iobase1+ATA_CB_SN, 0x55);
2399	outb(iobase1+ATA_CB_SC, 0x55);
2400	outb(iobase1+ATA_CB_SN, 0xaa);
2401
2402	// If we found something
2403	sc = inb(iobase1+ATA_CB_SC);
2404	sn = inb(iobase1+ATA_CB_SN);
2405
2406	if ( (sc == 0x55) && (sn == 0xaa) ) {
2407	write_byte(ebda_seg,&EbdaData->ata.devices[device].type,ATA_TYPE_UNKNOWN);
2408
2409	// reset the channel
2410	ata_reset(device);
2411
2412	// check for ATA or ATAPI
2413	outb(iobase1+ATA_CB_DH, slave ? ATA_CB_DH_DEV1 : ATA_CB_DH_DEV0);
2414	sc = inb(iobase1+ATA_CB_SC);
2415	sn = inb(iobase1+ATA_CB_SN);
2416
2417	if ((sc==0x01) && (sn==0x01)) {
2418	cl = inb(iobase1+ATA_CB_CL);
2419	ch = inb(iobase1+ATA_CB_CH);
2420	st = inb(iobase1+ATA_CB_STAT);
2421
2422	if ((cl==0x14) && (ch==0xeb)) {
2423	write_byte(ebda_seg,&EbdaData->ata.devices[device].type,ATA_TYPE_ATAPI);
2424	} else if ((cl==0x00) && (ch==0x00) && (st!=0x00)) {
2425	write_byte(ebda_seg,&EbdaData->ata.devices[device].type,ATA_TYPE_ATA);
2426	} else if ((cl==0xff) && (ch==0xff)) {
2427	write_byte(ebda_seg,&EbdaData->ata.devices[device].type,ATA_TYPE_NONE);
2428	}
2429	}
2430	}
2431
2432	#ifdef VBOX
2433	// Enable interrupts
2434	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
2435	#endif /* VBOX */
2436
2437	type=read_byte(ebda_seg,&EbdaData->ata.devices[device].type);
2438
2439	// Now we send a IDENTIFY command to ATA device
2440	if(type == ATA_TYPE_ATA) {
2441	Bit32u sectors;
2442	Bit16u cylinders, heads, spt, blksize;
2443	#ifdef VBOX
2444	Bit16u lcylinders, lheads, lspt;
2445	Bit8u chsgeo_base;
2446	#endif /* VBOX */
2447	Bit8u translation, removable, mode;
2448
2449	//Temporary values to do the transfer
2450	write_byte(ebda_seg,&EbdaData->ata.devices[device].device,ATA_DEVICE_HD);
2451	write_byte(ebda_seg,&EbdaData->ata.devices[device].mode, ATA_MODE_PIO16);
2452
2453	if (ata_cmd_data_in(device,ATA_CMD_IDENTIFY_DEVICE, 1, 0, 0, 0, 0L, get_SS(),buffer) !=0 )
2454	BX_PANIC("ata-detect: Failed to detect ATA device\n");
2455
2456	removable = (read_byte(get_SS(),buffer+0) & 0x80) ? 1 : 0;
2457	mode = read_byte(get_SS(),buffer+96) ? ATA_MODE_PIO32 : ATA_MODE_PIO16;
2458	#ifdef VBOX
2459	blksize = 512; /* There is no sector size field any more. */
2460	#else /* !VBOX */
2461	blksize = read_word(get_SS(),buffer+10);
2462	#endif /* !VBOX */
2463
2464	cylinders = read_word(get_SS(),buffer+(1*2)); // word 1
2465	heads = read_word(get_SS(),buffer+(3*2)); // word 3
2466	spt = read_word(get_SS(),buffer+(6*2)); // word 6
2467
2468	sectors = read_dword(get_SS(),buffer+(60*2)); // word 60 and word 61
2469	#ifdef VBOX
2470	/** @todo update sectors to be a 64 bit number (also lba...). */
2471	if (sectors == 268435455)
2472	sectors = read_dword(get_SS(),buffer+(100*2)); // words 100 to 103 (someday)
2473	switch (device)
2474	{
2475	case 0:
2476	chsgeo_base = 0x1e;
2477	break;
2478	case 1:
2479	chsgeo_base = 0x26;
2480	break;
2481	case 2:
2482	chsgeo_base = 0x67;
2483	break;
2484	case 3:
2485	chsgeo_base = 0x70;
2486	break;
2487	case 4:
2488	chsgeo_base = 0x40;
2489	break;
2490	case 5:
2491	chsgeo_base = 0x48;
2492	break;
2493	case 6:
2494	chsgeo_base = 0x50;
2495	break;
2496	case 7:
2497	chsgeo_base = 0x58;
2498	break;
2499	default:
2500	chsgeo_base = 0;
2501	}
2502	if (chsgeo_base != 0)
2503	{
2504	lcylinders = inb_cmos(chsgeo_base) + (inb_cmos(chsgeo_base+1) << 8);
2505	lheads = inb_cmos(chsgeo_base+2);
2506	lspt = inb_cmos(chsgeo_base+7);
2507	}
2508	else
2509	{
2510	lcylinders = 0;
2511	lheads = 0;
2512	lspt = 0;
2513	}
2514	BX_INFO("ata%d-%d: PCHS=%u/%d/%d LCHS=%u/%u/%u\n", channel, slave, cylinders, heads, spt, lcylinders, lheads, lspt);
2515	#endif /* VBOX */
2516
2517	write_byte(ebda_seg,&EbdaData->ata.devices[device].device,ATA_DEVICE_HD);
2518	write_byte(ebda_seg,&EbdaData->ata.devices[device].removable, removable);
2519	write_byte(ebda_seg,&EbdaData->ata.devices[device].mode, mode);
2520	write_word(ebda_seg,&EbdaData->ata.devices[device].blksize, blksize);
2521	write_word(ebda_seg,&EbdaData->ata.devices[device].pchs.heads, heads);
2522	write_word(ebda_seg,&EbdaData->ata.devices[device].pchs.cylinders, cylinders);
2523	write_word(ebda_seg,&EbdaData->ata.devices[device].pchs.spt, spt);
2524	write_dword(ebda_seg,&EbdaData->ata.devices[device].sectors, sectors);
2525	#ifdef VBOX
2526	write_word(ebda_seg,&EbdaData->ata.devices[device].lchs.heads, lheads);
2527	write_word(ebda_seg,&EbdaData->ata.devices[device].lchs.cylinders, lcylinders);
2528	write_word(ebda_seg,&EbdaData->ata.devices[device].lchs.spt, lspt);
2529	if (device < 2)
2530	{
2531	Bit8u sum, i;
2532	unsigned char *fdpt;
2533	if (device == 0)
2534	fdpt = &EbdaData->fdpt0;
2535	else
2536	fdpt = &EbdaData->fdpt1;
2537
2538	/* Update the DPT for drive 0/1 pointed to by Int41/46. This used
2539	* to be done at POST time with lots of ugly assembler code, which
2540	* isn't worth the effort of converting from AMI to Award CMOS
2541	* format. Just do it here. */
2542	write_word(ebda_seg, fdpt + 0x00, lcylinders);
2543	write_byte(ebda_seg, fdpt + 0x02, lheads);
2544	write_byte(ebda_seg, fdpt + 0x0e, lspt);
2545	write_word(ebda_seg, fdpt + 0x09, cylinders);
2546	write_byte(ebda_seg, fdpt + 0x0b, heads);
2547	write_byte(ebda_seg, fdpt + 0x04, spt);
2548	write_byte(ebda_seg, fdpt + 0x03, 0xa0);
2549	sum = 0;
2550	for (i = 0; i < 0xf; i++)
2551	sum += read_byte(ebda_seg, fdpt + i);
2552	sum = 1 - sum;
2553	write_byte(ebda_seg, fdpt + 0x0f, sum);
2554	}
2555	#else /* !VBOX */
2556	BX_INFO("ata%d-%d: PCHS=%u/%d/%d translation=", channel, slave,cylinders, heads, spt);
2557
2558	translation = inb_cmos(0x39 + channel/2);
2559	for (shift=device%4; shift>0; shift--) translation >>= 2;
2560	translation &= 0x03;
2561
2562	write_byte(ebda_seg,&EbdaData->ata.devices[device].translation, translation);
2563
2564	switch (translation) {
2565	case ATA_TRANSLATION_NONE:
2566	BX_INFO("none");
2567	break;
2568	case ATA_TRANSLATION_LBA:
2569	BX_INFO("lba");
2570	break;
2571	case ATA_TRANSLATION_LARGE:
2572	BX_INFO("large");
2573	break;
2574	case ATA_TRANSLATION_RECHS:
2575	BX_INFO("r-echs");
2576	break;
2577	}
2578	switch (translation) {
2579	case ATA_TRANSLATION_NONE:
2580	break;
2581	case ATA_TRANSLATION_LBA:
2582	spt = 63;
2583	sectors /= 63;
2584	heads = sectors / 1024;
2585	if (heads>128) heads = 255;
2586	else if (heads>64) heads = 128;
2587	else if (heads>32) heads = 64;
2588	else if (heads>16) heads = 32;
2589	else heads=16;
2590	cylinders = sectors / heads;
2591	break;
2592	case ATA_TRANSLATION_RECHS:
2593	// Take care not to overflow
2594	if (heads==16) {
2595	if(cylinders>61439) cylinders=61439;
2596	heads=15;
2597	cylinders = (Bit16u)((Bit32u)(cylinders)*16/15);
2598	}
2599	// then go through the large bitshift process
2600	case ATA_TRANSLATION_LARGE:
2601	while(cylinders > 1024) {
2602	cylinders >>= 1;
2603	heads <<= 1;
2604
2605	// If we max out the head count
2606	if (heads > 127) break;
2607	}
2608	break;
2609	}
2610	// clip to 1024 cylinders in lchs
2611	if (cylinders > 1024) cylinders=1024;
2612	BX_INFO(" LCHS=%d/%d/%d\n", cylinders, heads, spt);
2613
2614	write_word(ebda_seg,&EbdaData->ata.devices[device].lchs.heads, heads);
2615	write_word(ebda_seg,&EbdaData->ata.devices[device].lchs.cylinders, cylinders);
2616	write_word(ebda_seg,&EbdaData->ata.devices[device].lchs.spt, spt);
2617	#endif /* VBOX */
2618
2619	// fill hdidmap
2620	write_byte(ebda_seg,&EbdaData->ata.hdidmap[hdcount], device);
2621	hdcount++;
2622	}
2623
2624	// Now we send a IDENTIFY command to ATAPI device
2625	if(type == ATA_TYPE_ATAPI) {
2626
2627	Bit8u type, removable, mode;
2628	Bit16u blksize;
2629
2630	//Temporary values to do the transfer
2631	write_byte(ebda_seg,&EbdaData->ata.devices[device].device,ATA_DEVICE_CDROM);
2632	write_byte(ebda_seg,&EbdaData->ata.devices[device].mode, ATA_MODE_PIO16);
2633
2634	if (ata_cmd_data_in(device,ATA_CMD_IDENTIFY_DEVICE_PACKET, 1, 0, 0, 0, 0L, get_SS(),buffer) != 0)
2635	BX_PANIC("ata-detect: Failed to detect ATAPI device\n");
2636
2637	type = read_byte(get_SS(),buffer+1) & 0x1f;
2638	removable = (read_byte(get_SS(),buffer+0) & 0x80) ? 1 : 0;
2639	mode = read_byte(get_SS(),buffer+96) ? ATA_MODE_PIO32 : ATA_MODE_PIO16;
2640	blksize = 2048;
2641
2642	write_byte(ebda_seg,&EbdaData->ata.devices[device].device, type);
2643	write_byte(ebda_seg,&EbdaData->ata.devices[device].removable, removable);
2644	write_byte(ebda_seg,&EbdaData->ata.devices[device].mode, mode);
2645	write_word(ebda_seg,&EbdaData->ata.devices[device].blksize, blksize);
2646
2647	// fill cdidmap
2648	write_byte(ebda_seg,&EbdaData->ata.cdidmap[cdcount], device);
2649	cdcount++;
2650	}
2651
2652	{
2653	Bit32u sizeinmb;
2654	Bit16u ataversion;
2655	Bit8u c, i, version, model[41];
2656
2657	switch (type) {
2658	case ATA_TYPE_ATA:
2659	sizeinmb = read_dword(ebda_seg,&EbdaData->ata.devices[device].sectors);
2660	sizeinmb >>= 11;
2661	case ATA_TYPE_ATAPI:
2662	// Read ATA/ATAPI version
2663	ataversion=((Bit16u)(read_byte(get_SS(),buffer+161))<<8)\|read_byte(get_SS(),buffer+160);
2664	for(version=15;version>0;version--) {
2665	if((ataversion&(1<<version))!=0)
2666	break;
2667	}
2668
2669	// Read model name
2670	for(i=0;i<20;i++){
2671	write_byte(get_SS(),model+(i2),read_byte(get_SS(),buffer+(i2)+54+1));
2672	write_byte(get_SS(),model+(i2)+1,read_byte(get_SS(),buffer+(i2)+54));
2673	}
2674
2675	// Reformat
2676	write_byte(get_SS(),model+40,0x00);
2677	for(i=39;i>0;i--){
2678	if(read_byte(get_SS(),model+i)==0x20)
2679	write_byte(get_SS(),model+i,0x00);
2680	else break;
2681	}
2682	break;
2683	}
2684
2685	#ifdef VBOX
2686	// we don't want any noisy output for now
2687	#else /* !VBOX */
2688	switch (type) {
2689	case ATA_TYPE_ATA:
2690	printf("ata%d %s: ",channel,slave?" slave":"master");
2691	i=0; while(c=read_byte(get_SS(),model+i++)) printf("%c",c);
2692	printf(" ATA-%d Hard-Disk (%lu MBytes)\n", version, sizeinmb);
2693	break;
2694	case ATA_TYPE_ATAPI:
2695	printf("ata%d %s: ",channel,slave?" slave":"master");
2696	i=0; while(c=read_byte(get_SS(),model+i++)) printf("%c",c);
2697	if(read_byte(ebda_seg,&EbdaData->ata.devices[device].device)==ATA_DEVICE_CDROM)
2698	printf(" ATAPI-%d CD-Rom/DVD-Rom\n",version);
2699	else
2700	printf(" ATAPI-%d Device\n",version);
2701	break;
2702	case ATA_TYPE_UNKNOWN:
2703	printf("ata%d %s: Unknown device\n",channel,slave?" slave":"master");
2704	break;
2705	}
2706	#endif /* !VBOX */
2707	}
2708	}
2709
2710	// Store the devices counts
2711	write_byte(ebda_seg,&EbdaData->ata.hdcount, hdcount);
2712	write_byte(ebda_seg,&EbdaData->ata.cdcount, cdcount);
2713	write_byte(0x40,0x75, hdcount);
2714
2715	#ifdef VBOX
2716	// we don't want any noisy output for now
2717	#else /* !VBOX */
2718	printf("\n");
2719	#endif /* !VBOX */
2720
2721	// FIXME : should use bios=cmos\|auto\|disable bits
2722	// FIXME : should know about translation bits
2723	// FIXME : move hard_drive_post here
2724
2725	}
2726
2727	// ---------------------------------------------------------------------------
2728	// ATA/ATAPI driver : software reset
2729	// ---------------------------------------------------------------------------
2730	// ATA-3
2731	// 8.2.1 Software reset - Device 0
2732
2733	void ata_reset(device)
2734	Bit16u device;
2735	{
2736	Bit16u ebda_seg=read_word(0x0040,0x000E);
2737	Bit16u iobase1, iobase2;
2738	Bit8u channel, slave, sn, sc;
2739	Bit16u max;
2740	#ifdef VBOX
2741	Bit16u pdelay;
2742	#endif /* VBOX */
2743
2744	channel = device / 2;
2745	slave = device % 2;
2746
2747	iobase1 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase1);
2748	iobase2 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase2);
2749
2750	// Reset
2751
2752	// 8.2.1 (a) -- set SRST in DC
2753	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15 \| ATA_CB_DC_NIEN \| ATA_CB_DC_SRST);
2754
2755	// 8.2.1 (b) -- wait for BSY
2756	max=0xff;
2757	while(--max>0) {
2758	Bit8u status = inb(iobase1+ATA_CB_STAT);
2759	if ((status & ATA_CB_STAT_BSY) != 0) break;
2760	}
2761
2762	// 8.2.1 (f) -- clear SRST
2763	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15 \| ATA_CB_DC_NIEN);
2764
2765	if (read_byte(ebda_seg,&EbdaData->ata.devices[device].type) != ATA_TYPE_NONE) {
2766
2767	// 8.2.1 (g) -- check for sc==sn==0x01
2768	// select device
2769	outb(iobase1+ATA_CB_DH, slave?ATA_CB_DH_DEV1:ATA_CB_DH_DEV0);
2770	sc = inb(iobase1+ATA_CB_SC);
2771	sn = inb(iobase1+ATA_CB_SN);
2772
2773	if ( (sc==0x01) && (sn==0x01) ) {
2774
2775	// 8.2.1 (h) -- wait for not BSY
2776	#ifdef VBOX
2777	max=0xffff; /* The ATA specification says that the drive may be busy for up to 30 seconds. */
2778	#else /* !VBOX */
2779	max=0xff;
2780	#endif /* !VBOX */
2781	while(--max>0) {
2782	Bit8u status = inb(iobase1+ATA_CB_STAT);
2783	if ((status & ATA_CB_STAT_BSY) == 0) break;
2784	#ifdef VBOX
2785	pdelay=0xffff;
2786	while (--pdelay>0) {
2787	/* nothing */
2788	}
2789	#endif /* VBOX */
2790	}
2791	}
2792	}
2793
2794	// 8.2.1 (i) -- wait for DRDY
2795	#ifdef VBOX
2796	max=0x10; /* Speed up for virtual drives. Disks are immediately ready, CDs never */
2797	#else /* !VBOX */
2798	max=0xfff;
2799	#endif /* !VBOX */
2800	while(--max>0) {
2801	Bit8u status = inb(iobase1+ATA_CB_STAT);
2802	if ((status & ATA_CB_STAT_RDY) != 0) break;
2803	}
2804
2805	// Enable interrupts
2806	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
2807	}
2808
2809	// ---------------------------------------------------------------------------
2810	// ATA/ATAPI driver : execute a non data command
2811	// ---------------------------------------------------------------------------
2812
2813	Bit16u ata_cmd_non_data()
2814	{return 0;}
2815
2816	// ---------------------------------------------------------------------------
2817	// ATA/ATAPI driver : execute a data-in command
2818	// ---------------------------------------------------------------------------
2819	// returns
2820	// 0 : no error
2821	// 1 : BUSY bit set
2822	// 2 : read error
2823	// 3 : expected DRQ=1
2824	// 4 : no sectors left to read/verify
2825	// 5 : more sectors to read/verify
2826	// 6 : no sectors left to write
2827	// 7 : more sectors to write
2828	Bit16u ata_cmd_data_in(device, command, count, cylinder, head, sector, lba, segment, offset)
2829	Bit16u device, command, count, cylinder, head, sector, segment, offset;
2830	Bit32u lba;
2831	{
2832	Bit16u ebda_seg=read_word(0x0040,0x000E);
2833	Bit16u iobase1, iobase2, blksize;
2834	Bit8u channel, slave;
2835	Bit8u status, current, mode;
2836
2837	channel = device / 2;
2838	slave = device % 2;
2839
2840	iobase1 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase1);
2841	iobase2 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase2);
2842	mode = read_byte(ebda_seg, &EbdaData->ata.devices[device].mode);
2843	blksize = 0x200; // was = read_word(ebda_seg, &EbdaData->ata.devices[device].blksize);
2844	if (mode == ATA_MODE_PIO32) blksize>>=2;
2845	else blksize>>=1;
2846
2847	#ifdef VBOX
2848	status = inb(iobase1 + ATA_CB_STAT);
2849	if (status & ATA_CB_STAT_BSY)
2850	{
2851	// Enable interrupts
2852	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
2853	return 1;
2854	}
2855	#endif /* VBOX */
2856
2857	// sector will be 0 only on lba access. Convert to lba-chs
2858	if (sector == 0) {
2859	#ifdef VBOX
2860	if (count >= 256 \|\| lba + count >= 268435456)
2861	{
2862	sector = (lba & 0xff000000L) >> 24;
2863	cylinder = 0; /* The parameter lba is just a 32 bit value. */
2864	outb(iobase1 + ATA_CB_SC, (count & 0xff00) >> 8);
2865	outb(iobase1 + ATA_CB_SN, sector);
2866	outb(iobase1 + ATA_CB_CL, cylinder & 0x00ff);
2867	outb(iobase1 + ATA_CB_CH, cylinder >> 8);
2868	/* Leave the bottom 24 bits as is, they are treated correctly by the
2869	* LBA28 code path. */
2870	lba &= 0xffffff;
2871	}
2872	#endif /* VBOX */
2873	sector = (Bit16u) (lba & 0x000000ffL);
2874	lba >>= 8;
2875	cylinder = (Bit16u) (lba & 0x0000ffffL);
2876	lba >>= 16;
2877	head = ((Bit16u) (lba & 0x0000000fL)) \| 0x40;
2878	}
2879
2880	// Reset count of transferred data
2881	write_word(ebda_seg, &EbdaData->ata.trsfsectors,0);
2882	write_dword(ebda_seg, &EbdaData->ata.trsfbytes,0L);
2883	current = 0;
2884
2885	#ifndef VBOX
2886	status = inb(iobase1 + ATA_CB_STAT);
2887	if (status & ATA_CB_STAT_BSY) return 1;
2888	#endif /* !VBOX */
2889
2890	outb(iobase2 + ATA_CB_DC, ATA_CB_DC_HD15 \| ATA_CB_DC_NIEN);
2891	outb(iobase1 + ATA_CB_FR, 0x00);
2892	outb(iobase1 + ATA_CB_SC, count);
2893	outb(iobase1 + ATA_CB_SN, sector);
2894	outb(iobase1 + ATA_CB_CL, cylinder & 0x00ff);
2895	outb(iobase1 + ATA_CB_CH, cylinder >> 8);
2896	outb(iobase1 + ATA_CB_DH, (slave ? ATA_CB_DH_DEV1 : ATA_CB_DH_DEV0) \| (Bit8u) head );
2897	outb(iobase1 + ATA_CB_CMD, command);
2898
2899	while (1) {
2900	status = inb(iobase1 + ATA_CB_STAT);
2901	if ( !(status & ATA_CB_STAT_BSY) ) break;
2902	}
2903
2904	if (status & ATA_CB_STAT_ERR) {
2905	BX_DEBUG_ATA("ata_cmd_data_in : read error\n");
2906	#ifdef VBOX
2907	// Enable interrupts
2908	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
2909	#endif /* VBOX */
2910	return 2;
2911	} else if ( !(status & ATA_CB_STAT_DRQ) ) {
2912	BX_DEBUG_ATA("ata_cmd_data_in : DRQ not set (status %02x)\n", (unsigned) status);
2913	#ifdef VBOX
2914	// Enable interrupts
2915	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
2916	#endif /* VBOX */
2917	return 3;
2918	}
2919
2920	// FIXME : move seg/off translation here
2921
2922	ASM_START
2923	sti ;; enable higher priority interrupts
2924	ASM_END
2925
2926	while (1) {
2927
2928	ASM_START
2929	push bp
2930	mov bp, sp
2931	mov di, _ata_cmd_data_in.offset + 2[bp]
2932	mov ax, _ata_cmd_data_in.segment + 2[bp]
2933	mov cx, _ata_cmd_data_in.blksize + 2[bp]
2934
2935	;; adjust if there will be an overrun. 2K max sector size
2936	cmp di, #0xf800 ;;
2937	jbe ata_in_no_adjust
2938
2939	ata_in_adjust:
2940	sub di, #0x0800 ;; sub 2 kbytes from offset
2941	add ax, #0x0080 ;; add 2 Kbytes to segment
2942
2943	ata_in_no_adjust:
2944	mov es, ax ;; segment in es
2945
2946	mov dx, _ata_cmd_data_in.iobase1 + 2[bp] ;; ATA data read port
2947
2948	mov ah, _ata_cmd_data_in.mode + 2[bp]
2949	cmp ah, #ATA_MODE_PIO32
2950	je ata_in_32
2951
2952	ata_in_16:
2953	rep
2954	insw ;; CX words transfered from port(DX) to ES:[DI]
2955	jmp ata_in_done
2956
2957	ata_in_32:
2958	rep
2959	insd ;; CX dwords transfered from port(DX) to ES:[DI]
2960
2961	ata_in_done:
2962	mov _ata_cmd_data_in.offset + 2[bp], di
2963	mov _ata_cmd_data_in.segment + 2[bp], es
2964	pop bp
2965	ASM_END
2966
2967	current++;
2968	write_word(ebda_seg, &EbdaData->ata.trsfsectors,current);
2969	count--;
2970	#ifdef VBOX
2971	while (1) {
2972	status = inb(iobase1 + ATA_CB_STAT);
2973	if ( !(status & ATA_CB_STAT_BSY) ) break;
2974	}
2975	#else /* !VBOX */
2976	status = inb(iobase1 + ATA_CB_STAT);
2977	#endif /* !VBOX */
2978	if (count == 0) {
2979	if ( (status & (ATA_CB_STAT_BSY \| ATA_CB_STAT_RDY \| ATA_CB_STAT_DRQ \| ATA_CB_STAT_ERR) )
2980	!= ATA_CB_STAT_RDY ) {
2981	BX_DEBUG_ATA("ata_cmd_data_in : no sectors left (status %02x)\n", (unsigned) status);
2982	#ifdef VBOX
2983	// Enable interrupts
2984	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
2985	#endif /* VBOX */
2986	return 4;
2987	}
2988	break;
2989	}
2990	else {
2991	if ( (status & (ATA_CB_STAT_BSY \| ATA_CB_STAT_RDY \| ATA_CB_STAT_DRQ \| ATA_CB_STAT_ERR) )
2992	!= (ATA_CB_STAT_RDY \| ATA_CB_STAT_DRQ) ) {
2993	BX_DEBUG_ATA("ata_cmd_data_in : more sectors left (status %02x)\n", (unsigned) status);
2994	#ifdef VBOX
2995	// Enable interrupts
2996	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
2997	#endif /* VBOX */
2998	return 5;
2999	}
3000	continue;
3001	}
3002	}
3003	// Enable interrupts
3004	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3005	return 0;
3006	}
3007
3008	// ---------------------------------------------------------------------------
3009	// ATA/ATAPI driver : execute a data-out command
3010	// ---------------------------------------------------------------------------
3011	// returns
3012	// 0 : no error
3013	// 1 : BUSY bit set
3014	// 2 : read error
3015	// 3 : expected DRQ=1
3016	// 4 : no sectors left to read/verify
3017	// 5 : more sectors to read/verify
3018	// 6 : no sectors left to write
3019	// 7 : more sectors to write
3020	Bit16u ata_cmd_data_out(device, command, count, cylinder, head, sector, lba, segment, offset)
3021	Bit16u device, command, count, cylinder, head, sector, segment, offset;
3022	Bit32u lba;
3023	{
3024	Bit16u ebda_seg=read_word(0x0040,0x000E);
3025	Bit16u iobase1, iobase2, blksize;
3026	Bit8u channel, slave;
3027	Bit8u status, current, mode;
3028
3029	channel = device / 2;
3030	slave = device % 2;
3031
3032	iobase1 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase1);
3033	iobase2 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase2);
3034	mode = read_byte(ebda_seg, &EbdaData->ata.devices[device].mode);
3035	blksize = 0x200; // was = read_word(ebda_seg, &EbdaData->ata.devices[device].blksize);
3036	if (mode == ATA_MODE_PIO32) blksize>>=2;
3037	else blksize>>=1;
3038
3039	#ifdef VBOX
3040	status = inb(iobase1 + ATA_CB_STAT);
3041	if (status & ATA_CB_STAT_BSY)
3042	{
3043	// Enable interrupts
3044	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3045	return 1;
3046	}
3047	#endif /* VBOX */
3048
3049	// sector will be 0 only on lba access. Convert to lba-chs
3050	if (sector == 0) {
3051	#ifdef VBOX
3052	if (count >= 256 \|\| lba + count >= 268435456)
3053	{
3054	sector = (lba & 0xff000000L) >> 24;
3055	cylinder = 0; /* The parameter lba is just a 32 bit value. */
3056	outb(iobase1 + ATA_CB_SC, (count & 0xff00) >> 8);
3057	outb(iobase1 + ATA_CB_SN, sector);
3058	outb(iobase1 + ATA_CB_CL, cylinder & 0x00ff);
3059	outb(iobase1 + ATA_CB_CH, cylinder >> 8);
3060	/* Leave the bottom 24 bits as is, they are treated correctly by the
3061	* LBA28 code path. */
3062	lba &= 0xffffff;
3063	}
3064	#endif /* VBOX */
3065	sector = (Bit16u) (lba & 0x000000ffL);
3066	lba >>= 8;
3067	cylinder = (Bit16u) (lba & 0x0000ffffL);
3068	lba >>= 16;
3069	head = ((Bit16u) (lba & 0x0000000fL)) \| 0x40;
3070	}
3071
3072	// Reset count of transferred data
3073	write_word(ebda_seg, &EbdaData->ata.trsfsectors,0);
3074	write_dword(ebda_seg, &EbdaData->ata.trsfbytes,0L);
3075	current = 0;
3076
3077	#ifndef VBOX
3078	status = inb(iobase1 + ATA_CB_STAT);
3079	if (status & ATA_CB_STAT_BSY) return 1;
3080	#endif /* !VBOX */
3081
3082	outb(iobase2 + ATA_CB_DC, ATA_CB_DC_HD15 \| ATA_CB_DC_NIEN);
3083	outb(iobase1 + ATA_CB_FR, 0x00);
3084	outb(iobase1 + ATA_CB_SC, count);
3085	outb(iobase1 + ATA_CB_SN, sector);
3086	outb(iobase1 + ATA_CB_CL, cylinder & 0x00ff);
3087	outb(iobase1 + ATA_CB_CH, cylinder >> 8);
3088	outb(iobase1 + ATA_CB_DH, (slave ? ATA_CB_DH_DEV1 : ATA_CB_DH_DEV0) \| (Bit8u) head );
3089	outb(iobase1 + ATA_CB_CMD, command);
3090
3091	while (1) {
3092	status = inb(iobase1 + ATA_CB_STAT);
3093	if ( !(status & ATA_CB_STAT_BSY) ) break;
3094	}
3095
3096	if (status & ATA_CB_STAT_ERR) {
3097	BX_DEBUG_ATA("ata_cmd_data_out : read error\n");
3098	#ifdef VBOX
3099	// Enable interrupts
3100	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3101	#endif /* VBOX */
3102	return 2;
3103	} else if ( !(status & ATA_CB_STAT_DRQ) ) {
3104	BX_DEBUG_ATA("ata_cmd_data_out : DRQ not set (status %02x)\n", (unsigned) status);
3105	#ifdef VBOX
3106	// Enable interrupts
3107	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3108	#endif /* VBOX */
3109	return 3;
3110	}
3111
3112	// FIXME : move seg/off translation here
3113
3114	ASM_START
3115	sti ;; enable higher priority interrupts
3116	ASM_END
3117
3118	while (1) {
3119
3120	ASM_START
3121	push bp
3122	mov bp, sp
3123	mov si, _ata_cmd_data_out.offset + 2[bp]
3124	mov ax, _ata_cmd_data_out.segment + 2[bp]
3125	mov cx, _ata_cmd_data_out.blksize + 2[bp]
3126
3127	;; adjust if there will be an overrun. 2K max sector size
3128	cmp si, #0xf800 ;;
3129	jbe ata_out_no_adjust
3130
3131	ata_out_adjust:
3132	sub si, #0x0800 ;; sub 2 kbytes from offset
3133	add ax, #0x0080 ;; add 2 Kbytes to segment
3134
3135	ata_out_no_adjust:
3136	mov es, ax ;; segment in es
3137
3138	mov dx, _ata_cmd_data_out.iobase1 + 2[bp] ;; ATA data write port
3139
3140	mov ah, _ata_cmd_data_out.mode + 2[bp]
3141	cmp ah, #ATA_MODE_PIO32
3142	je ata_out_32
3143
3144	ata_out_16:
3145	seg ES
3146	rep
3147	outsw ;; CX words transfered from port(DX) to ES:[SI]
3148	jmp ata_out_done
3149
3150	ata_out_32:
3151	seg ES
3152	rep
3153	outsd ;; CX dwords transfered from port(DX) to ES:[SI]
3154
3155	ata_out_done:
3156	mov _ata_cmd_data_out.offset + 2[bp], si
3157	mov _ata_cmd_data_out.segment + 2[bp], es
3158	pop bp
3159	ASM_END
3160
3161	current++;
3162	write_word(ebda_seg, &EbdaData->ata.trsfsectors,current);
3163	count--;
3164	#ifdef VBOX
3165	while (1) {
3166	status = inb(iobase1 + ATA_CB_STAT);
3167	if ( !(status & ATA_CB_STAT_BSY) ) break;
3168	}
3169	#else /* !VBOX */
3170	status = inb(iobase1 + ATA_CB_STAT);
3171	#endif /* VBOX */
3172	if (count == 0) {
3173	if ( (status & (ATA_CB_STAT_BSY \| ATA_CB_STAT_RDY \| ATA_CB_STAT_DF \| ATA_CB_STAT_DRQ \| ATA_CB_STAT_ERR) )
3174	!= ATA_CB_STAT_RDY ) {
3175	BX_DEBUG_ATA("ata_cmd_data_out : no sectors left (status %02x)\n", (unsigned) status);
3176	#ifdef VBOX
3177	// Enable interrupts
3178	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3179	#endif /* VBOX */
3180	return 6;
3181	}
3182	break;
3183	}
3184	else {
3185	if ( (status & (ATA_CB_STAT_BSY \| ATA_CB_STAT_RDY \| ATA_CB_STAT_DRQ \| ATA_CB_STAT_ERR) )
3186	!= (ATA_CB_STAT_RDY \| ATA_CB_STAT_DRQ) ) {
3187	BX_DEBUG_ATA("ata_cmd_data_out : more sectors left (status %02x)\n", (unsigned) status);
3188	#ifdef VBOX
3189	// Enable interrupts
3190	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3191	#endif /* VBOX */
3192	return 7;
3193	}
3194	continue;
3195	}
3196	}
3197	// Enable interrupts
3198	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3199	return 0;
3200	}
3201
3202	// ---------------------------------------------------------------------------
3203	// ATA/ATAPI driver : execute a packet command
3204	// ---------------------------------------------------------------------------
3205	// returns
3206	// 0 : no error
3207	// 1 : error in parameters
3208	// 2 : BUSY bit set
3209	// 3 : error
3210	// 4 : not ready
3211	Bit16u ata_cmd_packet(device, cmdlen, cmdseg, cmdoff, header, length, inout, bufseg, bufoff)
3212	Bit8u cmdlen,inout;
3213	Bit16u device,cmdseg, cmdoff, bufseg, bufoff;
3214	Bit16u header;
3215	Bit32u length;
3216	{
3217	Bit16u ebda_seg=read_word(0x0040,0x000E);
3218	Bit16u iobase1, iobase2;
3219	Bit16u lcount, lbefore, lafter, count;
3220	Bit8u channel, slave;
3221	Bit8u status, mode, lmode;
3222	Bit32u total, transfer;
3223
3224	channel = device / 2;
3225	slave = device % 2;
3226
3227	// Data out is not supported yet
3228	if (inout == ATA_DATA_OUT) {
3229	BX_INFO("ata_cmd_packet: DATA_OUT not supported yet\n");
3230	return 1;
3231	}
3232
3233	// The header length must be even
3234	if (header & 1) {
3235	BX_DEBUG_ATA("ata_cmd_packet : header must be even (%04x)\n",header);
3236	return 1;
3237	}
3238
3239	iobase1 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase1);
3240	iobase2 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase2);
3241	mode = read_byte(ebda_seg, &EbdaData->ata.devices[device].mode);
3242	transfer= 0L;
3243
3244	if (cmdlen < 12) cmdlen=12;
3245	if (cmdlen > 12) cmdlen=16;
3246	cmdlen>>=1;
3247
3248	// Reset count of transferred data
3249	write_word(ebda_seg, &EbdaData->ata.trsfsectors,0);
3250	write_dword(ebda_seg, &EbdaData->ata.trsfbytes,0L);
3251
3252	status = inb(iobase1 + ATA_CB_STAT);
3253	if (status & ATA_CB_STAT_BSY) return 2;
3254
3255	outb(iobase2 + ATA_CB_DC, ATA_CB_DC_HD15 \| ATA_CB_DC_NIEN);
3256	// outb(iobase1 + ATA_CB_FR, 0x00);
3257	// outb(iobase1 + ATA_CB_SC, 0x00);
3258	// outb(iobase1 + ATA_CB_SN, 0x00);
3259	outb(iobase1 + ATA_CB_CL, 0xfff0 & 0x00ff);
3260	outb(iobase1 + ATA_CB_CH, 0xfff0 >> 8);
3261	outb(iobase1 + ATA_CB_DH, slave ? ATA_CB_DH_DEV1 : ATA_CB_DH_DEV0);
3262	outb(iobase1 + ATA_CB_CMD, ATA_CMD_PACKET);
3263
3264	// Device should ok to receive command
3265	while (1) {
3266	status = inb(iobase1 + ATA_CB_STAT);
3267	if ( !(status & ATA_CB_STAT_BSY) ) break;
3268	}
3269
3270	if (status & ATA_CB_STAT_ERR) {
3271	BX_DEBUG_ATA("ata_cmd_packet : error, status is %02x\n",status);
3272	#ifdef VBOX
3273	// Enable interrupts
3274	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3275	#endif /* VBOX */
3276	return 3;
3277	} else if ( !(status & ATA_CB_STAT_DRQ) ) {
3278	BX_DEBUG_ATA("ata_cmd_packet : DRQ not set (status %02x)\n", (unsigned) status);
3279	#ifdef VBOX
3280	// Enable interrupts
3281	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3282	#endif /* VBOX */
3283	return 4;
3284	}
3285
3286	// Normalize address
3287	cmdseg += (cmdoff / 16);
3288	cmdoff %= 16;
3289
3290	// Send command to device
3291	ASM_START
3292	sti ;; enable higher priority interrupts
3293
3294	push bp
3295	mov bp, sp
3296
3297	mov si, _ata_cmd_packet.cmdoff + 2[bp]
3298	mov ax, _ata_cmd_packet.cmdseg + 2[bp]
3299	mov cx, _ata_cmd_packet.cmdlen + 2[bp]
3300	mov es, ax ;; segment in es
3301
3302	mov dx, _ata_cmd_packet.iobase1 + 2[bp] ;; ATA data write port
3303
3304	seg ES
3305	rep
3306	outsw ;; CX words transfered from port(DX) to ES:[SI]
3307
3308	pop bp
3309	ASM_END
3310
3311	if (inout == ATA_DATA_NO) {
3312	status = inb(iobase1 + ATA_CB_STAT);
3313	}
3314	else {
3315	while (1) {
3316
3317	#ifdef VBOX
3318	while (1) {
3319	status = inb(iobase1 + ATA_CB_STAT);
3320	if ( !(status & ATA_CB_STAT_BSY) ) break;
3321	}
3322	#else /* VBOX */
3323	status = inb(iobase1 + ATA_CB_STAT);
3324	#endif /* VBOX */
3325
3326	// Check if command completed
3327	if ( (status & (ATA_CB_STAT_BSY \| ATA_CB_STAT_DRQ) ) ==0 ) break;
3328
3329	if (status & ATA_CB_STAT_ERR) {
3330	BX_DEBUG_ATA("ata_cmd_packet : error (status %02x)\n",status);
3331	#ifdef VBOX
3332	// Enable interrupts
3333	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3334	#endif /* VBOX */
3335	return 3;
3336	}
3337
3338	// Device must be ready to send data
3339	if ( (status & (ATA_CB_STAT_BSY \| ATA_CB_STAT_RDY \| ATA_CB_STAT_DRQ \| ATA_CB_STAT_ERR) )
3340	!= (ATA_CB_STAT_RDY \| ATA_CB_STAT_DRQ) ) {
3341	BX_DEBUG_ATA("ata_cmd_packet : not ready (status %02x)\n", status);
3342	#ifdef VBOX
3343	// Enable interrupts
3344	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3345	#endif /* VBOX */
3346	return 4;
3347	}
3348
3349	// Normalize address
3350	bufseg += (bufoff / 16);
3351	bufoff %= 16;
3352
3353	// Get the byte count
3354	lcount = ((Bit16u)(inb(iobase1 + ATA_CB_CH))<<8)+inb(iobase1 + ATA_CB_CL);
3355
3356	// adjust to read what we want
3357	if(header>lcount) {
3358	lbefore=lcount;
3359	header-=lcount;
3360	lcount=0;
3361	}
3362	else {
3363	lbefore=header;
3364	header=0;
3365	lcount-=lbefore;
3366	}
3367
3368	if(lcount>length) {
3369	lafter=lcount-length;
3370	lcount=length;
3371	length=0;
3372	}
3373	else {
3374	lafter=0;
3375	length-=lcount;
3376	}
3377
3378	// Save byte count
3379	count = lcount;
3380
3381	BX_DEBUG_ATA("Trying to read %04x bytes (%04x %04x %04x) ",lbefore+lcount+lafter,lbefore,lcount,lafter);
3382	BX_DEBUG_ATA("to 0x%04x:0x%04x\n",bufseg,bufoff);
3383
3384	// If counts not dividable by 4, use 16bits mode
3385	lmode = mode;
3386	if (lbefore & 0x03) lmode=ATA_MODE_PIO16;
3387	if (lcount & 0x03) lmode=ATA_MODE_PIO16;
3388	if (lafter & 0x03) lmode=ATA_MODE_PIO16;
3389
3390	// adds an extra byte if count are odd. before is always even
3391	if (lcount & 0x01) {
3392	lcount+=1;
3393	if ((lafter > 0) && (lafter & 0x01)) {
3394	lafter-=1;
3395	}
3396	}
3397
3398	if (lmode == ATA_MODE_PIO32) {
3399	lcount>>=2; lbefore>>=2; lafter>>=2;
3400	}
3401	else {
3402	lcount>>=1; lbefore>>=1; lafter>>=1;
3403	}
3404
3405	; // FIXME bcc bug
3406
3407	ASM_START
3408	push bp
3409	mov bp, sp
3410
3411	mov dx, _ata_cmd_packet.iobase1 + 2[bp] ;; ATA data read port
3412
3413	mov cx, _ata_cmd_packet.lbefore + 2[bp]
3414	jcxz ata_packet_no_before
3415
3416	mov ah, _ata_cmd_packet.lmode + 2[bp]
3417	cmp ah, #ATA_MODE_PIO32
3418	je ata_packet_in_before_32
3419
3420	ata_packet_in_before_16:
3421	in ax, dx
3422	loop ata_packet_in_before_16
3423	jmp ata_packet_no_before
3424
3425	ata_packet_in_before_32:
3426	push eax
3427	ata_packet_in_before_32_loop:
3428	in eax, dx
3429	loop ata_packet_in_before_32_loop
3430	pop eax
3431
3432	ata_packet_no_before:
3433	mov cx, _ata_cmd_packet.lcount + 2[bp]
3434	jcxz ata_packet_after
3435
3436	mov di, _ata_cmd_packet.bufoff + 2[bp]
3437	mov ax, _ata_cmd_packet.bufseg + 2[bp]
3438	mov es, ax
3439
3440	mov ah, _ata_cmd_packet.lmode + 2[bp]
3441	cmp ah, #ATA_MODE_PIO32
3442	je ata_packet_in_32
3443
3444	ata_packet_in_16:
3445	rep
3446	insw ;; CX words transfered tp port(DX) to ES:[DI]
3447	jmp ata_packet_after
3448
3449	ata_packet_in_32:
3450	rep
3451	insd ;; CX dwords transfered to port(DX) to ES:[DI]
3452
3453	ata_packet_after:
3454	mov cx, _ata_cmd_packet.lafter + 2[bp]
3455	jcxz ata_packet_done
3456
3457	mov ah, _ata_cmd_packet.lmode + 2[bp]
3458	cmp ah, #ATA_MODE_PIO32
3459	je ata_packet_in_after_32
3460
3461	ata_packet_in_after_16:
3462	in ax, dx
3463	loop ata_packet_in_after_16
3464	jmp ata_packet_done
3465
3466	ata_packet_in_after_32:
3467	push eax
3468	ata_packet_in_after_32_loop:
3469	in eax, dx
3470	loop ata_packet_in_after_32_loop
3471	pop eax
3472
3473	ata_packet_done:
3474	pop bp
3475	ASM_END
3476
3477	// Compute new buffer address
3478	bufoff += count;
3479
3480	// Save transferred bytes count
3481	transfer += count;
3482	write_dword(ebda_seg, &EbdaData->ata.trsfbytes,transfer);
3483	}
3484	}
3485
3486	// Final check, device must be ready
3487	if ( (status & (ATA_CB_STAT_BSY \| ATA_CB_STAT_RDY \| ATA_CB_STAT_DF \| ATA_CB_STAT_DRQ \| ATA_CB_STAT_ERR) )
3488	!= ATA_CB_STAT_RDY ) {
3489	BX_DEBUG_ATA("ata_cmd_packet : not ready (status %02x)\n", (unsigned) status);
3490	#ifdef VBOX
3491	// Enable interrupts
3492	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3493	#endif /* VBOX */
3494	return 4;
3495	}
3496
3497	// Enable interrupts
3498	outb(iobase2+ATA_CB_DC, ATA_CB_DC_HD15);
3499	return 0;
3500	}
3501
3502	// ---------------------------------------------------------------------------
3503	// End of ATA/ATAPI Driver
3504	// ---------------------------------------------------------------------------
3505
3506	// ---------------------------------------------------------------------------
3507	// Start of ATA/ATAPI generic functions
3508	// ---------------------------------------------------------------------------
3509
3510	Bit16u
3511	atapi_get_sense(device)
3512	Bit16u device;
3513	{
3514	Bit8u atacmd[12];
3515	Bit8u buffer[16];
3516	Bit8u i;
3517
3518	memsetb(get_SS(),atacmd,0,12);
3519
3520	// Request SENSE
3521	atacmd[0]=0x03;
3522	atacmd[4]=0x20;
3523	if (ata_cmd_packet(device, 12, get_SS(), atacmd, 0, 16L, ATA_DATA_IN, get_SS(), buffer) != 0)
3524	return 0x0002;
3525
3526	if ((buffer[0] & 0x7e) == 0x70) {
3527	return (((Bit16u)buffer[2]&0x0f)*0x100)+buffer[12];
3528	}
3529
3530	return 0;
3531	}
3532
3533	Bit16u
3534	atapi_is_ready(device)
3535	Bit16u device;
3536	{
3537	Bit8u atacmd[12];
3538	Bit8u buffer[];
3539
3540	memsetb(get_SS(),atacmd,0,12);
3541
3542	// Test Unit Ready
3543	if (ata_cmd_packet(device, 12, get_SS(), atacmd, 0, 0L, ATA_DATA_NO, get_SS(), buffer) != 0)
3544	return 0x000f;
3545
3546	if (atapi_get_sense(device) !=0 ) {
3547	memsetb(get_SS(),atacmd,0,12);
3548
3549	// try to send Test Unit Ready again
3550	if (ata_cmd_packet(device, 12, get_SS(), atacmd, 0, 0L, ATA_DATA_NO, get_SS(), buffer) != 0)
3551	return 0x000f;
3552
3553	return atapi_get_sense(device);
3554	}
3555	return 0;
3556	}
3557
3558	Bit16u
3559	atapi_is_cdrom(device)
3560	Bit8u device;
3561	{
3562	Bit16u ebda_seg=read_word(0x0040,0x000E);
3563
3564	if (device >= BX_MAX_ATA_DEVICES)
3565	return 0;
3566
3567	if (read_byte(ebda_seg,&EbdaData->ata.devices[device].type) != ATA_TYPE_ATAPI)
3568	return 0;
3569
3570	if (read_byte(ebda_seg,&EbdaData->ata.devices[device].device) != ATA_DEVICE_CDROM)
3571	return 0;
3572
3573	return 1;
3574	}
3575
3576	// ---------------------------------------------------------------------------
3577	// End of ATA/ATAPI generic functions
3578	// ---------------------------------------------------------------------------
3579
3580	#endif // BX_USE_ATADRV
3581
3582	#if BX_ELTORITO_BOOT
3583
3584	// ---------------------------------------------------------------------------
3585	// Start of El-Torito boot functions
3586	// ---------------------------------------------------------------------------
3587
3588	void
3589	cdemu_init()
3590	{
3591	Bit16u ebda_seg=read_word(0x0040,0x000E);
3592
3593	// the only important data is this one for now
3594	write_byte(ebda_seg,&EbdaData->cdemu.active,0x00);
3595	}
3596
3597	Bit8u
3598	cdemu_isactive()
3599	{
3600	Bit16u ebda_seg=read_word(0x0040,0x000E);
3601
3602	return(read_byte(ebda_seg,&EbdaData->cdemu.active));
3603	}
3604
3605	Bit8u
3606	cdemu_emulated_drive()
3607	{
3608	Bit16u ebda_seg=read_word(0x0040,0x000E);
3609
3610	return(read_byte(ebda_seg,&EbdaData->cdemu.emulated_drive));
3611	}
3612
3613	static char isotag[6]="CD001";
3614	static char eltorito[24]="EL TORITO SPECIFICATION";
3615	//
3616	// Returns ah: emulated drive, al: error code
3617	//
3618	Bit16u
3619	cdrom_boot()
3620	{
3621	Bit16u ebda_seg=read_word(0x0040,0x000E);
3622	Bit8u atacmd[12], buffer[2048];
3623	Bit32u lba;
3624	Bit16u boot_segment, nbsectors, i, error;
3625	Bit8u device;
3626	#ifdef VBOX
3627	Bit8u read_try;
3628	#endif /* VBOX */
3629
3630	// Find out the first cdrom
3631	for (device=0; device<BX_MAX_ATA_DEVICES;device++) {
3632	if (atapi_is_cdrom(device)) break;
3633	}
3634
3635	// if not found
3636	if(device >= BX_MAX_ATA_DEVICES) return 2;
3637
3638	// Read the Boot Record Volume Descriptor
3639	memsetb(get_SS(),atacmd,0,12);
3640	atacmd[0]=0x28; // READ command
3641	atacmd[7]=(0x01 & 0xff00) >> 8; // Sectors
3642	atacmd[8]=(0x01 & 0x00ff); // Sectors
3643	atacmd[2]=(0x11 & 0xff000000) >> 24; // LBA
3644	atacmd[3]=(0x11 & 0x00ff0000) >> 16;
3645	atacmd[4]=(0x11 & 0x0000ff00) >> 8;
3646	atacmd[5]=(0x11 & 0x000000ff);
3647	#ifdef VBOX
3648	for (read_try = 0; read_try <= 4; read_try++)
3649	{
3650	error = ata_cmd_packet(device, 12, get_SS(), atacmd, 0, 2048L, ATA_DATA_IN, get_SS(), buffer);
3651	if (!error)
3652	break;
3653	}
3654	if (error)
3655	return 3;
3656	#else /* !VBOX */
3657	if((error = ata_cmd_packet(device, 12, get_SS(), atacmd, 0, 2048L, ATA_DATA_IN, get_SS(), buffer)) != 0)
3658	return 3;
3659	#endif /* !VBOX */
3660
3661	// Validity checks
3662	if(buffer[0]!=0)return 4;
3663	for(i=0;i<5;i++){
3664	if(buffer[1+i]!=read_byte(0xf000,&isotag[i]))return 5;
3665	}
3666	for(i=0;i<23;i++)
3667	if(buffer[7+i]!=read_byte(0xf000,&eltorito[i]))return 6;
3668
3669	// ok, now we calculate the Boot catalog address
3670	lba=buffer[0x4A]0x1000000+buffer[0x49]0x10000+buffer[0x48]*0x100+buffer[0x47];
3671
3672	// And we read the Boot Catalog
3673	memsetb(get_SS(),atacmd,0,12);
3674	atacmd[0]=0x28; // READ command
3675	atacmd[7]=(0x01 & 0xff00) >> 8; // Sectors
3676	atacmd[8]=(0x01 & 0x00ff); // Sectors
3677	atacmd[2]=(lba & 0xff000000) >> 24; // LBA
3678	atacmd[3]=(lba & 0x00ff0000) >> 16;
3679	atacmd[4]=(lba & 0x0000ff00) >> 8;
3680	atacmd[5]=(lba & 0x000000ff);
3681	if((error = ata_cmd_packet(device, 12, get_SS(), atacmd, 0, 2048L, ATA_DATA_IN, get_SS(), buffer)) != 0)
3682	return 7;
3683
3684	// Validation entry
3685	if(buffer[0x00]!=0x01)return 8; // Header
3686	if(buffer[0x01]!=0x00)return 9; // Platform
3687	if(buffer[0x1E]!=0x55)return 10; // key 1
3688	if(buffer[0x1F]!=0xAA)return 10; // key 2
3689
3690	// Initial/Default Entry
3691	if(buffer[0x20]!=0x88)return 11; // Bootable
3692
3693	write_byte(ebda_seg,&EbdaData->cdemu.media,buffer[0x21]);
3694	if(buffer[0x21]==0){
3695	// FIXME ElTorito Hardcoded. cdrom is hardcoded as device 0xE0.
3696	// Win2000 cd boot needs to know it booted from cd
3697	write_byte(ebda_seg,&EbdaData->cdemu.emulated_drive,0xE0);
3698	}
3699	else if(buffer[0x21]<4)
3700	write_byte(ebda_seg,&EbdaData->cdemu.emulated_drive,0x00);
3701	else
3702	write_byte(ebda_seg,&EbdaData->cdemu.emulated_drive,0x80);
3703
3704	write_byte(ebda_seg,&EbdaData->cdemu.controller_index,device/2);
3705	write_byte(ebda_seg,&EbdaData->cdemu.device_spec,device%2);
3706
3707	boot_segment=buffer[0x23]*0x100+buffer[0x22];
3708	if(boot_segment==0x0000)boot_segment=0x07C0;
3709
3710	write_word(ebda_seg,&EbdaData->cdemu.load_segment,boot_segment);
3711	write_word(ebda_seg,&EbdaData->cdemu.buffer_segment,0x0000);
3712
3713	nbsectors=buffer[0x27]*0x100+buffer[0x26];
3714	write_word(ebda_seg,&EbdaData->cdemu.sector_count,nbsectors);
3715
3716	lba=buffer[0x2B]0x1000000+buffer[0x2A]0x10000+buffer[0x29]*0x100+buffer[0x28];
3717	write_dword(ebda_seg,&EbdaData->cdemu.ilba,lba);
3718
3719	// And we read the image in memory
3720	memsetb(get_SS(),atacmd,0,12);
3721	atacmd[0]=0x28; // READ command
3722	atacmd[7]=((1+(nbsectors-1)/4) & 0xff00) >> 8; // Sectors
3723	atacmd[8]=((1+(nbsectors-1)/4) & 0x00ff); // Sectors
3724	atacmd[2]=(lba & 0xff000000) >> 24; // LBA
3725	atacmd[3]=(lba & 0x00ff0000) >> 16;
3726	atacmd[4]=(lba & 0x0000ff00) >> 8;
3727	atacmd[5]=(lba & 0x000000ff);
3728	if((error = ata_cmd_packet(device, 12, get_SS(), atacmd, 0, nbsectors*512L, ATA_DATA_IN, boot_segment,0)) != 0)
3729	return 12;
3730
3731	// Remember the media type
3732	switch(read_byte(ebda_seg,&EbdaData->cdemu.media)) {
3733	case 0x01: // 1.2M floppy
3734	write_word(ebda_seg,&EbdaData->cdemu.vdevice.spt,15);
3735	write_word(ebda_seg,&EbdaData->cdemu.vdevice.cylinders,80);
3736	write_word(ebda_seg,&EbdaData->cdemu.vdevice.heads,2);
3737	break;
3738	case 0x02: // 1.44M floppy
3739	write_word(ebda_seg,&EbdaData->cdemu.vdevice.spt,18);
3740	write_word(ebda_seg,&EbdaData->cdemu.vdevice.cylinders,80);
3741	write_word(ebda_seg,&EbdaData->cdemu.vdevice.heads,2);
3742	break;
3743	case 0x03: // 2.88M floppy
3744	write_word(ebda_seg,&EbdaData->cdemu.vdevice.spt,36);
3745	write_word(ebda_seg,&EbdaData->cdemu.vdevice.cylinders,80);
3746	write_word(ebda_seg,&EbdaData->cdemu.vdevice.heads,2);
3747	break;
3748	case 0x04: // Harddrive
3749	write_word(ebda_seg,&EbdaData->cdemu.vdevice.spt,read_byte(boot_segment,446+6)&0x3f);
3750	write_word(ebda_seg,&EbdaData->cdemu.vdevice.cylinders,
3751	(read_byte(boot_segment,446+6)<<2) + read_byte(boot_segment,446+7) + 1);
3752	write_word(ebda_seg,&EbdaData->cdemu.vdevice.heads,read_byte(boot_segment,446+5) + 1);
3753	break;
3754	}
3755
3756	if(read_byte(ebda_seg,&EbdaData->cdemu.media)!=0) {
3757	// Increase bios installed hardware number of devices
3758	if(read_byte(ebda_seg,&EbdaData->cdemu.emulated_drive)==0x00)
3759	write_byte(0x40,0x10,read_byte(0x40,0x10)\|0x41);
3760	else
3761	write_byte(ebda_seg, &EbdaData->ata.hdcount, read_byte(ebda_seg, &EbdaData->ata.hdcount) + 1);
3762	}
3763
3764
3765	// everything is ok, so from now on, the emulation is active
3766	if(read_byte(ebda_seg,&EbdaData->cdemu.media)!=0)
3767	write_byte(ebda_seg,&EbdaData->cdemu.active,0x01);
3768
3769	// return the boot drive + no error
3770	return (read_byte(ebda_seg,&EbdaData->cdemu.emulated_drive)*0x100)+0;
3771	}
3772
3773	// ---------------------------------------------------------------------------
3774	// End of El-Torito boot functions
3775	// ---------------------------------------------------------------------------
3776	#endif // BX_ELTORITO_BOOT
3777
3778	#ifdef VBOX_WITH_SCSI
3779	# include "scsi.c"
3780	#endif
3781
3782	void
3783	int14_function(regs, ds, iret_addr)
3784	pusha_regs_t regs; // regs pushed from PUSHA instruction
3785	Bit16u ds; // previous DS:, DS set to 0x0000 by asm wrapper
3786	iret_addr_t iret_addr; // CS,IP,Flags pushed from original INT call
3787	{
3788	Bit16u addr,timer,val16;
3789	Bit8u timeout;
3790
3791	ASM_START
3792	sti
3793	ASM_END
3794
3795	addr = read_word(0x0040, (regs.u.r16.dx << 1));
3796	timeout = read_byte(0x0040, 0x007C + regs.u.r16.dx);
3797	if ((regs.u.r16.dx < 4) && (addr > 0)) {
3798	switch (regs.u.r8.ah) {
3799	case 0:
3800	outb(addr+3, inb(addr+3) \| 0x80);
3801	if (regs.u.r8.al & 0xE0 == 0) {
3802	outb(addr, 0x17);
3803	outb(addr+1, 0x04);
3804	} else {
3805	val16 = 0x600 >> ((regs.u.r8.al & 0xE0) >> 5);
3806	outb(addr, val16 & 0xFF);
3807	outb(addr+1, val16 >> 8);
3808	}
3809	outb(addr+3, regs.u.r8.al & 0x1F);
3810	regs.u.r8.ah = inb(addr+5);
3811	regs.u.r8.al = inb(addr+6);
3812	ClearCF(iret_addr.flags);
3813	break;
3814	case 1:
3815	timer = read_word(0x0040, 0x006C);
3816	while (((inb(addr+5) & 0x60) != 0x60) && (timeout)) {
3817	val16 = read_word(0x0040, 0x006C);
3818	if (val16 != timer) {
3819	timer = val16;
3820	timeout--;
3821	}
3822	}
3823	if (timeout) outb(addr, regs.u.r8.al);
3824	regs.u.r8.ah = inb(addr+5);
3825	if (!timeout) regs.u.r8.ah \|= 0x80;
3826	ClearCF(iret_addr.flags);
3827	break;
3828	case 2:
3829	timer = read_word(0x0040, 0x006C);
3830	while (((inb(addr+5) & 0x01) == 0) && (timeout)) {
3831	val16 = read_word(0x0040, 0x006C);
3832	if (val16 != timer) {
3833	timer = val16;
3834	timeout--;
3835	}
3836	}
3837	if (timeout) {
3838	regs.u.r8.ah = 0;
3839	regs.u.r8.al = inb(addr);
3840	} else {
3841	regs.u.r8.ah = inb(addr+5);
3842	}
3843	ClearCF(iret_addr.flags);
3844	break;
3845	case 3:
3846	regs.u.r8.ah = inb(addr+5);
3847	regs.u.r8.al = inb(addr+6);
3848	ClearCF(iret_addr.flags);
3849	break;
3850	default:
3851	SetCF(iret_addr.flags); // Unsupported
3852	}
3853	} else {
3854	SetCF(iret_addr.flags); // Unsupported
3855	}
3856	}
3857
3858	void
3859	int15_function(regs, ES, DS, FLAGS)
3860	pusha_regs_t regs; // REGS pushed via pusha
3861	Bit16u ES, DS, FLAGS;
3862	{
3863	Bit16u ebda_seg=read_word(0x0040,0x000E);
3864	bx_bool prev_a20_enable;
3865	Bit16u base15_00;
3866	Bit8u base23_16;
3867	Bit16u ss;
3868	Bit16u BX,CX,DX;
3869
3870	Bit16u bRegister;
3871	Bit8u irqDisable;
3872
3873	BX_DEBUG_INT15("int15 AX=%04x\n",regs.u.r16.ax);
3874
3875	switch (regs.u.r8.ah) {
3876	#ifdef VBOX
3877	case 0x00: /* assorted functions */
3878	if (regs.u.r8.al != 0xc0)
3879	goto undecoded;
3880	/* GRUB calls int15 with ax=0x00c0 to get the ROM configuration table,
3881	* which we don't support, but logging that event is annoying. In fact
3882	* it is likely that they just misread some specs, because there is a
3883	* int15 BIOS function AH=0xc0 which sounds quite similar to what GRUB
3884	* wants to achieve. */
3885	SET_CF();
3886	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
3887	break;
3888	#endif
3889	case 0x24: /* A20 Control */
3890	switch (regs.u.r8.al) {
3891	case 0x00:
3892	set_enable_a20(0);
3893	CLEAR_CF();
3894	regs.u.r8.ah = 0;
3895	break;
3896	case 0x01:
3897	set_enable_a20(1);
3898	CLEAR_CF();
3899	regs.u.r8.ah = 0;
3900	break;
3901	case 0x02:
3902	regs.u.r8.al = (inb(0x92) >> 1) & 0x01;
3903	CLEAR_CF();
3904	regs.u.r8.ah = 0;
3905	break;
3906	case 0x03:
3907	CLEAR_CF();
3908	regs.u.r8.ah = 0;
3909	regs.u.r16.bx = 3;
3910	break;
3911	default:
3912	BX_INFO("int15: Func 24h, subfunc %02xh, A20 gate control not supported\n", (unsigned) regs.u.r8.al);
3913	SET_CF();
3914	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
3915	}
3916	break;
3917
3918	case 0x41:
3919	SET_CF();
3920	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
3921	break;
3922
3923	case 0x4f:
3924	/* keyboard intercept */
3925	#if BX_CPU < 2
3926	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
3927	#else
3928	// nop
3929	#endif
3930	SET_CF();
3931	break;
3932
3933	case 0x52: // removable media eject
3934	CLEAR_CF();
3935	regs.u.r8.ah = 0; // "ok ejection may proceed"
3936	break;
3937
3938	case 0x83: {
3939	if( regs.u.r8.al == 0 ) {
3940	// Set Interval requested.
3941	if( ( read_byte( 0x40, 0xA0 ) & 1 ) == 0 ) {
3942	// Interval not already set.
3943	write_byte( 0x40, 0xA0, 1 ); // Set status byte.
3944	write_word( 0x40, 0x98, ES ); // Byte location, segment
3945	write_word( 0x40, 0x9A, regs.u.r16.bx ); // Byte location, offset
3946	write_word( 0x40, 0x9C, regs.u.r16.dx ); // Low word, delay
3947	write_word( 0x40, 0x9E, regs.u.r16.cx ); // High word, delay.
3948	CLEAR_CF( );
3949	irqDisable = inb( 0xA1 );
3950	outb( 0xA1, irqDisable & 0xFE );
3951	bRegister = inb_cmos( 0xB ); // Unmask IRQ8 so INT70 will get through.
3952	outb_cmos( 0xB, bRegister \| 0x40 ); // Turn on the Periodic Interrupt timer
3953	} else {
3954	// Interval already set.
3955	BX_DEBUG_INT15("int15: Func 83h, failed, already waiting.\n" );
3956	SET_CF();
3957	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
3958	}
3959	} else if( regs.u.r8.al == 1 ) {
3960	// Clear Interval requested
3961	write_byte( 0x40, 0xA0, 0 ); // Clear status byte
3962	CLEAR_CF( );
3963	bRegister = inb_cmos( 0xB );
3964	outb_cmos( 0xB, bRegister & ~0x40 ); // Turn off the Periodic Interrupt timer
3965	} else {
3966	BX_DEBUG_INT15("int15: Func 83h, failed.\n" );
3967	SET_CF();
3968	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
3969	regs.u.r8.al--;
3970	}
3971
3972	break;
3973	}
3974
3975	case 0x87:
3976	#if BX_CPU < 3
3977	# error "Int15 function 87h not supported on < 80386"
3978	#endif
3979	// +++ should probably have descriptor checks
3980	// +++ should have exception handlers
3981
3982	// turn off interrupts
3983	ASM_START
3984	cli
3985	ASM_END
3986
3987	prev_a20_enable = set_enable_a20(1); // enable A20 line
3988
3989	// 128K max of transfer on 386+ ???
3990	// source == destination ???
3991
3992	// ES:SI points to descriptor table
3993	// offset use initially comments
3994	// ==============================================
3995	// 00..07 Unused zeros Null descriptor
3996	// 08..0f GDT zeros filled in by BIOS
3997	// 10..17 source ssssssss source of data
3998	// 18..1f dest dddddddd destination of data
3999	// 20..27 CS zeros filled in by BIOS
4000	// 28..2f SS zeros filled in by BIOS
4001
4002	//es:si
4003	//eeee0
4004	//0ssss
4005	//-----
4006
4007	// check for access rights of source & dest here
4008
4009	// Initialize GDT descriptor
4010	base15_00 = (ES << 4) + regs.u.r16.si;
4011	base23_16 = ES >> 12;
4012	if (base15_00 < (ES<<4))
4013	base23_16++;
4014	write_word(ES, regs.u.r16.si+0x08+0, 47); // limit 15:00 = 6 * 8bytes/descriptor
4015	write_word(ES, regs.u.r16.si+0x08+2, base15_00);// base 15:00
4016	write_byte(ES, regs.u.r16.si+0x08+4, base23_16);// base 23:16
4017	write_byte(ES, regs.u.r16.si+0x08+5, 0x93); // access
4018	write_word(ES, regs.u.r16.si+0x08+6, 0x0000); // base 31:24/reserved/limit 19:16
4019
4020	// Initialize CS descriptor
4021	write_word(ES, regs.u.r16.si+0x20+0, 0xffff);// limit 15:00 = normal 64K limit
4022	write_word(ES, regs.u.r16.si+0x20+2, 0x0000);// base 15:00
4023	write_byte(ES, regs.u.r16.si+0x20+4, 0x000f);// base 23:16
4024	write_byte(ES, regs.u.r16.si+0x20+5, 0x9b); // access
4025	write_word(ES, regs.u.r16.si+0x20+6, 0x0000);// base 31:24/reserved/limit 19:16
4026
4027	// Initialize SS descriptor
4028	ss = get_SS();
4029	base15_00 = ss << 4;
4030	base23_16 = ss >> 12;
4031	write_word(ES, regs.u.r16.si+0x28+0, 0xffff); // limit 15:00 = normal 64K limit
4032	write_word(ES, regs.u.r16.si+0x28+2, base15_00);// base 15:00
4033	write_byte(ES, regs.u.r16.si+0x28+4, base23_16);// base 23:16
4034	write_byte(ES, regs.u.r16.si+0x28+5, 0x93); // access
4035	write_word(ES, regs.u.r16.si+0x28+6, 0x0000); // base 31:24/reserved/limit 19:16
4036
4037	CX = regs.u.r16.cx;
4038	ASM_START
4039	// Compile generates locals offset info relative to SP.
4040	// Get CX (word count) from stack.
4041	mov bx, sp
4042	SEG SS
4043	mov cx, _int15_function.CX [bx]
4044
4045	// since we need to set SS:SP, save them to the BDA
4046	// for future restore
4047	push eax
4048	xor eax, eax
4049	mov ds, ax
4050	mov 0x0469, ss
4051	mov 0x0467, sp
4052
4053	SEG ES
4054	lgdt [si + 0x08]
4055	SEG CS
4056	lidt [pmode_IDT_info]
4057	;; perhaps do something with IDT here
4058
4059	;; set PE bit in CR0
4060	mov eax, cr0
4061	or al, #0x01
4062	mov cr0, eax
4063	;; far jump to flush CPU queue after transition to protected mode
4064	JMP_AP(0x0020, protected_mode)
4065
4066	protected_mode:
4067	;; GDT points to valid descriptor table, now load SS, DS, ES
4068	mov ax, #0x28 ;; 101 000 = 5th descriptor in table, TI=GDT, RPL=00
4069	mov ss, ax
4070	mov ax, #0x10 ;; 010 000 = 2nd descriptor in table, TI=GDT, RPL=00
4071	mov ds, ax
4072	mov ax, #0x18 ;; 011 000 = 3rd descriptor in table, TI=GDT, RPL=00
4073	mov es, ax
4074	xor si, si
4075	xor di, di
4076	cld
4077	rep
4078	movsw ;; move CX words from DS:SI to ES:DI
4079
4080	;; make sure DS and ES limits are 64KB
4081	mov ax, #0x28
4082	mov ds, ax
4083	mov es, ax
4084
4085	;; reset PG bit in CR0 ???
4086	mov eax, cr0
4087	and al, #0xFE
4088	mov cr0, eax
4089
4090	;; far jump to flush CPU queue after transition to real mode
4091	JMP_AP(0xf000, real_mode)
4092
4093	real_mode:
4094	;; restore IDT to normal real-mode defaults
4095	SEG CS
4096	lidt [rmode_IDT_info]
4097
4098	// restore SS:SP from the BDA
4099	xor ax, ax
4100	mov ds, ax
4101	mov ss, 0x0469
4102	mov sp, 0x0467
4103	pop eax
4104	ASM_END
4105
4106	set_enable_a20(prev_a20_enable);
4107
4108	// turn back on interrupts
4109	ASM_START
4110	sti
4111	ASM_END
4112
4113	regs.u.r8.ah = 0;
4114	CLEAR_CF();
4115	break;
4116
4117
4118	case 0x88:
4119	// Get the amount of extended memory (above 1M)
4120	#if BX_CPU < 2
4121	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
4122	SET_CF();
4123	#else
4124	regs.u.r8.al = inb_cmos(0x30);
4125	regs.u.r8.ah = inb_cmos(0x31);
4126
4127	// According to Ralf Brown's interrupt the limit should be 15M,
4128	// but real machines mostly return max. 63M.
4129	if(regs.u.r16.ax > 0xffc0)
4130	regs.u.r16.ax = 0xffc0;
4131
4132	CLEAR_CF();
4133	#endif
4134	break;
4135
4136	#ifdef VBOX
4137	case 0x89:
4138	// Switch to Protected Mode.
4139	// ES:DI points to user-supplied GDT
4140	// BH/BL contains starting interrupt numbers for PIC0/PIC1
4141	// This subfunction does not return!
4142
4143	// turn off interrupts
4144	ASM_START
4145	cli
4146	ASM_END
4147
4148	set_enable_a20(1); // enable A20 line; we're supposed to fail if that fails
4149
4150	// Initialize CS descriptor for BIOS
4151	write_word(ES, regs.u.r16.si+0x38+0, 0xffff);// limit 15:00 = normal 64K limit
4152	write_word(ES, regs.u.r16.si+0x38+2, 0x0000);// base 15:00
4153	write_byte(ES, regs.u.r16.si+0x38+4, 0x000f);// base 23:16 (hardcoded to f000:0000)
4154	write_byte(ES, regs.u.r16.si+0x38+5, 0x9b); // access
4155	write_word(ES, regs.u.r16.si+0x38+6, 0x0000);// base 31:24/reserved/limit 19:16
4156
4157	BX = regs.u.r16.bx;
4158	ASM_START
4159	// Compiler generates locals offset info relative to SP.
4160	// Get BX (PIC offsets) from stack.
4161	mov bx, sp
4162	SEG SS
4163	mov bx, _int15_function.BX [bx]
4164
4165	// Program PICs
4166	mov al, #0x11 ; send initialisation commands
4167	out 0x20, al
4168	out 0xa0, al
4169	mov al, bh
4170	out 0x21, al
4171	mov al, bl
4172	out 0xa1, al
4173	mov al, #0x04
4174	out 0x21, al
4175	mov al, #0x02
4176	out 0xa1, al
4177	mov al, #0x01
4178	out 0x21, al
4179	out 0xa1, al
4180	mov al, #0xff ; mask all IRQs, user must re-enable
4181	out 0x21, al
4182	out 0xa1, al
4183
4184	// Load GDT and IDT from supplied data
4185	SEG ES
4186	lgdt [si + 0x08]
4187	SEG ES
4188	lidt [si + 0x10]
4189
4190	// set PE bit in CR0
4191	mov eax, cr0
4192	or al, #0x01
4193	mov cr0, eax
4194	// far jump to flush CPU queue after transition to protected mode
4195	JMP_AP(0x0038, protmode_switch)
4196
4197	protmode_switch:
4198	;; GDT points to valid descriptor table, now load SS, DS, ES
4199	mov ax, #0x28
4200	mov ss, ax
4201	mov ax, #0x18
4202	mov ds, ax
4203	mov ax, #0x20
4204	mov es, ax
4205
4206	// unwind the stack - this will break if calling sequence changes!
4207	mov sp,bp
4208	add sp,#4 ; skip return address
4209	popa ; restore regs
4210	pop ax ; skip saved es
4211	pop ax ; skip saved ds
4212	pop ax ; skip saved flags
4213
4214	// return to caller - note that we do not use IRET because
4215	// we cannot enable interrupts
4216	pop cx ; get return offset
4217	pop ax ; skip return segment
4218	pop ax ; skip flags
4219	mov ax, #0x30 ; ah must be 0 on successful exit
4220	push ax
4221	push cx ; re-create modified ret address on stack
4222	retf
4223
4224	ASM_END
4225
4226	break;
4227	#endif
4228
4229	case 0x90:
4230	/* Device busy interrupt. Called by Int 16h when no key available */
4231	break;
4232
4233	case 0x91:
4234	/* Interrupt complete. Called by Int 16h when key becomes available */
4235	break;
4236
4237	case 0xbf:
4238	BX_INFO("*** int 15h function AH=bf not yet supported!\n");
4239	SET_CF();
4240	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
4241	break;
4242
4243	case 0xC0:
4244	#if 0
4245	SET_CF();
4246	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
4247	break;
4248	#endif
4249	CLEAR_CF();
4250	regs.u.r8.ah = 0;
4251	regs.u.r16.bx = BIOS_CONFIG_TABLE;
4252	ES = 0xF000;
4253	break;
4254
4255	case 0xc1:
4256	ES = ebda_seg;
4257	CLEAR_CF();
4258	break;
4259
4260	case 0xd8:
4261	bios_printf(BIOS_PRINTF_DEBUG, "EISA BIOS not present\n");
4262	SET_CF();
4263	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
4264	break;
4265
4266	#ifdef VBOX
4267	/* Make the BIOS warning for pretty much every Linux kernel start
4268	* disappear - it calls with ax=0xe980 to figure out SMI info. */
4269	case 0xe9: /* SMI functions (SpeedStep and similar things) */
4270	SET_CF();
4271	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
4272	break;
4273	undecoded:
4274	#endif /* VBOX */
4275	default:
4276	BX_INFO("*** int 15h function AX=%04x, BX=%04x not yet supported!\n",
4277	(unsigned) regs.u.r16.ax, (unsigned) regs.u.r16.bx);
4278	SET_CF();
4279	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
4280	break;
4281	}
4282	}
4283
4284	#if BX_USE_PS2_MOUSE
4285	void
4286	int15_function_mouse(regs, ES, DS, FLAGS)
4287	pusha_regs_t regs; // REGS pushed via pusha
4288	Bit16u ES, DS, FLAGS;
4289	{
4290	Bit16u ebda_seg=read_word(0x0040,0x000E);
4291	Bit8u mouse_flags_1, mouse_flags_2;
4292	Bit16u mouse_driver_seg;
4293	Bit16u mouse_driver_offset;
4294	Bit8u mouse_cmd;
4295	Bit8u ret, mouse_data1, mouse_data2, mouse_data3;
4296
4297	BX_DEBUG_INT15("int15 AX=%04x\n",regs.u.r16.ax);
4298
4299	switch (regs.u.r8.ah) {
4300	case 0xC2:
4301	// Return Codes status in AH
4302	// =========================
4303	// 00: success
4304	// 01: invalid subfunction (AL > 7)
4305	// 02: invalid input value (out of allowable range)
4306	// 03: interface error
4307	// 04: resend command received from mouse controller,
4308	// device driver should attempt command again
4309	// 05: cannot enable mouse, since no far call has been installed
4310	// 80/86: mouse service not implemented
4311
4312	if (regs.u.r8.al > 7) {
4313	BX_DEBUG_INT15("unsupported subfn\n");
4314	// invalid function
4315	SET_CF();
4316	regs.u.r8.ah = 1;
4317	break;
4318	}
4319
4320	// Valid subfn; disable AUX input and IRQ12, assume no error
4321	set_kbd_command_byte(0x65);
4322	CLEAR_CF();
4323	regs.u.r8.ah = 0;
4324
4325	switch (regs.u.r8.al) {
4326	case 0: // Disable/Enable Mouse
4327	BX_DEBUG_INT15("case 0: ");
4328	if (regs.u.r8.bh > 1) {
4329	BX_DEBUG_INT15("INT 15h C2 AL=0, BH=%02x\n", (unsigned) regs.u.r8.bh);
4330	// invalid subfunction
4331	SET_CF();
4332	regs.u.r8.ah = 1;
4333	break;
4334	}
4335	mouse_flags_2 = read_byte(ebda_seg, 0x0027);
4336	if ( (mouse_flags_2 & 0x80) == 0 ) {
4337	BX_DEBUG_INT15("INT 15h C2 Enable/Disable Mouse, no far call handler\n");
4338	SET_CF();
4339	regs.u.r8.ah = 5; // no far call installed
4340	break;
4341	}
4342	if (regs.u.r8.bh == 0) {
4343	BX_DEBUG_INT15("Disable Mouse\n");
4344	mouse_cmd = 0xF5; // disable mouse command
4345	} else {
4346	BX_DEBUG_INT15("Enable Mouse\n");
4347	mouse_cmd = 0xF4; // enable mouse command
4348	}
4349
4350	ret = send_to_mouse_ctrl(mouse_cmd); // disable mouse command
4351	if (ret == 0) {
4352	ret = get_mouse_data(&mouse_data1);
4353	if ( (ret == 0) \|\| (mouse_data1 == 0xFA) ) {
4354	// success
4355	break;
4356	}
4357	}
4358
4359	// interface error
4360	SET_CF();
4361	regs.u.r8.ah = 3;
4362	break;
4363
4364	case 5: // Initialize Mouse
4365	// Valid package sizes are 1 to 8
4366	if ( (regs.u.r8.bh < 1) \|\| (regs.u.r8.bh > 8) ) {
4367	SET_CF();
4368	regs.u.r8.ah = 2; // invalid input
4369	break;
4370	}
4371	mouse_flags_2 = read_byte(ebda_seg, 0x0027);
4372	mouse_flags_2 = (mouse_flags_2 & 0xf8) \| (regs.u.r8.bh - 1);
4373	write_byte(ebda_seg, 0x0027, mouse_flags_2);
4374	// fall through!
4375
4376	case 1: // Reset Mouse
4377	BX_DEBUG_INT15("case 1 or 5:\n");
4378	// clear current package byte index
4379	mouse_flags_1 = read_byte(ebda_seg, 0x0026);
4380	mouse_flags_1 = mouse_flags_1 & 0xf8;
4381	write_byte(ebda_seg, 0x0026, mouse_flags_1);
4382	ret = send_to_mouse_ctrl(0xFF); // reset mouse command
4383	if (ret == 0) {
4384	ret = get_mouse_data(&mouse_data3);
4385	// if no mouse attached, it will return RESEND
4386	if (mouse_data3 == 0xfe) {
4387	SET_CF();
4388	regs.u.r8.ah = 4; // resend
4389	break;
4390	}
4391	if (mouse_data3 != 0xfa)
4392	BX_PANIC("Mouse reset returned %02x (should be ack)\n", (unsigned)mouse_data3);
4393	if ( ret == 0 ) {
4394	ret = get_mouse_data(&mouse_data1);
4395	if ( ret == 0 ) {
4396	ret = get_mouse_data(&mouse_data2);
4397	if ( ret == 0 ) {
4398	// success
4399	regs.u.r8.bl = mouse_data1;
4400	regs.u.r8.bh = mouse_data2;
4401	break;
4402	}
4403	}
4404	}
4405	}
4406
4407	// interface error
4408	SET_CF();
4409	regs.u.r8.ah = 3;
4410	break;
4411
4412	case 2: // Set Sample Rate
4413	BX_DEBUG_INT15("case 2:\n");
4414	switch (regs.u.r8.bh) {
4415	case 0: mouse_data1 = 10; break; // 10 reports/sec
4416	case 1: mouse_data1 = 20; break; // 20 reports/sec
4417	case 2: mouse_data1 = 40; break; // 40 reports/sec
4418	case 3: mouse_data1 = 60; break; // 60 reports/sec
4419	case 4: mouse_data1 = 80; break; // 80 reports/sec
4420	case 5: mouse_data1 = 100; break; // 100 reports/sec (default)
4421	case 6: mouse_data1 = 200; break; // 200 reports/sec
4422	default: mouse_data1 = 0;
4423	}
4424	if (mouse_data1 > 0) {
4425	ret = send_to_mouse_ctrl(0xF3); // set sample rate command
4426	if (ret == 0) {
4427	ret = get_mouse_data(&mouse_data2);
4428	ret = send_to_mouse_ctrl(mouse_data1);
4429	ret = get_mouse_data(&mouse_data2);
4430	// success
4431	} else {
4432	// interface error
4433	SET_CF();
4434	regs.u.r8.ah = 3;
4435	}
4436	} else {
4437	// invalid input
4438	SET_CF();
4439	regs.u.r8.ah = 2;
4440	}
4441	break;
4442
4443	case 3: // Set Resolution
4444	BX_DEBUG_INT15("case 3:\n");
4445	// BX:
4446	// 0 = 25 dpi, 1 count per millimeter
4447	// 1 = 50 dpi, 2 counts per millimeter
4448	// 2 = 100 dpi, 4 counts per millimeter
4449	// 3 = 200 dpi, 8 counts per millimeter
4450	if (regs.u.r8.bh < 4) {
4451	ret = send_to_mouse_ctrl(0xE8); // set resolution command
4452	if (ret == 0) {
4453	ret = get_mouse_data(&mouse_data1);
4454	if (mouse_data1 != 0xfa)
4455	BX_PANIC("Mouse status returned %02x (should be ack)\n", (unsigned)mouse_data1);
4456	ret = send_to_mouse_ctrl(regs.u.r8.bh);
4457	ret = get_mouse_data(&mouse_data1);
4458	if (mouse_data1 != 0xfa)
4459	BX_PANIC("Mouse status returned %02x (should be ack)\n", (unsigned)mouse_data1);
4460	// success
4461	} else {
4462	// interface error
4463	SET_CF();
4464	regs.u.r8.ah = 3;
4465	}
4466	} else {
4467	// invalid input
4468	SET_CF();
4469	regs.u.r8.ah = 2;
4470	}
4471	break;
4472
4473	case 4: // Get Device ID
4474	BX_DEBUG_INT15("case 4:\n");
4475	ret = send_to_mouse_ctrl(0xF2); // get mouse ID command
4476	if (ret == 0) {
4477	ret = get_mouse_data(&mouse_data1);
4478	ret = get_mouse_data(&mouse_data2);
4479	regs.u.r8.bh = mouse_data2;
4480	// success
4481	} else {
4482	// interface error
4483	SET_CF();
4484	regs.u.r8.ah = 3;
4485	}
4486	break;
4487
4488	case 6: // Return Status & Set Scaling Factor...
4489	BX_DEBUG_INT15("case 6:\n");
4490	switch (regs.u.r8.bh) {
4491	case 0: // Return Status
4492	ret = send_to_mouse_ctrl(0xE9); // get mouse info command
4493	if (ret == 0) {
4494	ret = get_mouse_data(&mouse_data1);
4495	if (mouse_data1 != 0xfa)
4496	BX_PANIC("Mouse status returned %02x (should be ack)\n", (unsigned)mouse_data1);
4497	if (ret == 0) {
4498	ret = get_mouse_data(&mouse_data1);
4499	if ( ret == 0 ) {
4500	ret = get_mouse_data(&mouse_data2);
4501	if ( ret == 0 ) {
4502	ret = get_mouse_data(&mouse_data3);
4503	if ( ret == 0 ) {
4504	regs.u.r8.bl = mouse_data1;
4505	regs.u.r8.cl = mouse_data2;
4506	regs.u.r8.dl = mouse_data3;
4507	// success
4508	break;
4509	}
4510	}
4511	}
4512	}
4513	}
4514
4515	// interface error
4516	SET_CF();
4517	regs.u.r8.ah = 3;
4518	break;
4519
4520	case 1: // Set Scaling Factor to 1:1
4521	case 2: // Set Scaling Factor to 2:1
4522	if (regs.u.r8.bh == 1) {
4523	ret = send_to_mouse_ctrl(0xE6);
4524	} else {
4525	ret = send_to_mouse_ctrl(0xE7);
4526	}
4527	if (ret == 0) {
4528	get_mouse_data(&mouse_data1);
4529	ret = (mouse_data1 != 0xFA);
4530	}
4531	if (ret != 0) {
4532	// interface error
4533	SET_CF();
4534	regs.u.r8.ah = 3;
4535	}
4536	break;
4537
4538	default:
4539	BX_PANIC("INT 15h C2 AL=6, BH=%02x\n", (unsigned) regs.u.r8.bh);
4540	// invalid subfunction
4541	SET_CF();
4542	regs.u.r8.ah = 1;
4543	}
4544	break;
4545
4546	case 7: // Set Mouse Handler Address
4547	BX_DEBUG_INT15("case 7:\n");
4548	mouse_driver_seg = ES;
4549	mouse_driver_offset = regs.u.r16.bx;
4550	write_word(ebda_seg, 0x0022, mouse_driver_offset);
4551	write_word(ebda_seg, 0x0024, mouse_driver_seg);
4552	mouse_flags_2 = read_byte(ebda_seg, 0x0027);
4553	if (mouse_driver_offset == 0 && mouse_driver_seg == 0) {
4554	/* remove handler */
4555	if ( (mouse_flags_2 & 0x80) != 0 ) {
4556	mouse_flags_2 &= ~0x80;
4557	}
4558	}
4559	else {
4560	/* install handler */
4561	mouse_flags_2 \|= 0x80;
4562	}
4563	write_byte(ebda_seg, 0x0027, mouse_flags_2);
4564	break;
4565
4566	default:
4567	BX_PANIC("INT 15h C2 default case entered\n");
4568	// invalid subfunction
4569	SET_CF();
4570	regs.u.r8.ah = 1;
4571	}
4572	BX_DEBUG_INT15("returning cf = %u, ah = %02x\n", (unsigned)GET_CF(), (unsigned)regs.u.r8.ah);
4573	// Re-enable AUX input and IRQ12
4574	set_kbd_command_byte(0x47);
4575	break;
4576
4577	default:
4578	BX_INFO("*** int 15h function AX=%04x, BX=%04x not yet supported!\n",
4579	(unsigned) regs.u.r16.ax, (unsigned) regs.u.r16.bx);
4580	SET_CF();
4581	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
4582	break;
4583	}
4584	}
4585	#endif
4586
4587
4588	void set_e820_range(ES, DI, start, end, extra_start, extra_end, type)
4589	Bit16u ES;
4590	Bit16u DI;
4591	Bit32u start;
4592	Bit32u end;
4593	Bit8u extra_start;
4594	Bit8u extra_end;
4595	Bit16u type;
4596	{
4597	write_word(ES, DI, start);
4598	write_word(ES, DI+2, start >> 16);
4599	write_word(ES, DI+4, 0x00); /** @todo r=bird: why write it twice? */
4600	write_word(ES, DI+4, extra_start);
4601	write_word(ES, DI+6, 0x00);
4602
4603	end -= start;
4604	extra_end -= extra_start;
4605	write_word(ES, DI+8, end);
4606	write_word(ES, DI+10, end >> 16);
4607	#ifdef VBOX
4608	if (end == 0)
4609	write_word(ES, DI+12, 0x0001);
4610	else
4611	/** @todo XXX: nike - is it really correct? see QEMU BIOS patch */
4612	write_word(ES, DI+12, extra_end);
4613	#else /* !VBOX */
4614	write_word(ES, DI+12, 0x0000);
4615	#endif /* !VBOX */
4616	write_word(ES, DI+14, 0x0000);
4617
4618	write_word(ES, DI+16, type);
4619	write_word(ES, DI+18, 0x0);
4620	}
4621
4622	void
4623	int15_function32(regs, ES, DS, FLAGS)
4624	pushad_regs_t regs; // REGS pushed via pushad
4625	Bit16u ES, DS, FLAGS;
4626	{
4627	Bit32u extended_memory_size=0; // 64bits long
4628	#ifdef VBOX_WITH_MORE_THAN_4GB
4629	Bit32u extra_lowbits_memory_size=0;
4630	#endif
4631	Bit16u CX,DX;
4632	#ifdef VBOX_WITH_MORE_THAN_4GB
4633	Bit8u extra_highbits_memory_size=0;
4634	#endif
4635
4636	BX_DEBUG_INT15("int15 AX=%04x\n",regs.u.r16.ax);
4637
4638	switch (regs.u.r8.ah) {
4639	case 0x86:
4640	// Wait for CX:DX microseconds. currently using the
4641	// refresh request port 0x61 bit4, toggling every 15usec
4642
4643	CX = regs.u.r16.cx;
4644	DX = regs.u.r16.dx;
4645
4646	ASM_START
4647	sti
4648
4649	;; Get the count in eax
4650	;; VBOX: corrected _int15_function -> _int15_function32 here.
4651	mov bx, sp
4652	SEG SS
4653	mov ax, _int15_function32.CX [bx]
4654	shl eax, #16
4655	SEG SS
4656	mov ax, _int15_function32.DX [bx]
4657
4658	;; convert to numbers of 15usec ticks
4659	mov ebx, #15
4660	xor edx, edx
4661	div eax, ebx
4662	mov ecx, eax
4663
4664	;; wait for ecx number of refresh requests
4665	in al, #0x61
4666	and al,#0x10
4667	mov ah, al
4668
4669	or ecx, ecx
4670	je int1586_tick_end
4671	int1586_tick:
4672	in al, #0x61
4673	and al,#0x10
4674	cmp al, ah
4675	je int1586_tick
4676	mov ah, al
4677	dec ecx
4678	jnz int1586_tick
4679	int1586_tick_end:
4680	ASM_END
4681
4682	break;
4683
4684	case 0xe8:
4685	switch(regs.u.r8.al)
4686	{
4687	case 0x20: // coded by osmaker aka K.J.
4688	if(regs.u.r32.edx == 0x534D4150)
4689	{
4690	extended_memory_size = inb_cmos(0x35);
4691	extended_memory_size <<= 8;
4692	extended_memory_size \|= inb_cmos(0x34);
4693	extended_memory_size *= 64;
4694	// greater than EFF00000???
4695	if(extended_memory_size > 0x3bc000) {
4696	extended_memory_size = 0x3bc000; // everything after this is reserved memory until we get to 0x100000000
4697	}
4698	extended_memory_size *= 1024;
4699	extended_memory_size += (16L * 1024 * 1024);
4700
4701	if(extended_memory_size <= (16L * 1024 * 1024)) {
4702	extended_memory_size = inb_cmos(0x31);
4703	extended_memory_size <<= 8;
4704	extended_memory_size \|= inb_cmos(0x30);
4705	extended_memory_size *= 1024;
4706	}
4707
4708	#ifdef VBOX_WITH_MORE_THAN_4GB /* bird: later (btw. this ain't making sense complixity wise, unless its a AMI/AWARD/PHOENIX interface) */
4709	extra_lowbits_memory_size = inb_cmos(0x61);
4710	extra_lowbits_memory_size <<= 8;
4711	extra_lowbits_memory_size \|= inb_cmos(0x62);
4712	extra_lowbits_memory_size *= 64;
4713	extra_lowbits_memory_size *= 1024;
4714	extra_highbits_memory_size = inb_cmos(0x63);
4715	#endif
4716
4717	switch(regs.u.r16.bx)
4718	{
4719	case 0:
4720	set_e820_range(ES, regs.u.r16.di,
4721	0x0000000L, 0x0009fc00L, 0, 0, 1);
4722	regs.u.r32.ebx = 1;
4723	regs.u.r32.eax = 0x534D4150;
4724	regs.u.r32.ecx = 0x14;
4725	CLEAR_CF();
4726	return;
4727	break;
4728	case 1:
4729	set_e820_range(ES, regs.u.r16.di,
4730	0x0009fc00L, 0x000a0000L, 0, 0, 2);
4731	regs.u.r32.ebx = 2;
4732	regs.u.r32.eax = 0x534D4150;
4733	regs.u.r32.ecx = 0x14;
4734	CLEAR_CF();
4735	return;
4736	break;
4737	case 2:
4738	#ifdef VBOX
4739	/* Mark the BIOS as reserved. VBox doesn't currently
4740	* use the 0xe0000-0xeffff area. It does use the
4741	* 0xd0000-0xdffff area for the BIOS logo, but it's
4742	* not worth marking it as reserved. Note that various
4743	* Windows versions don't accept (read: in debug builds
4744	* they trigger the "Too many similar traps" assertion)
4745	* a single reserved range from 0xd0000 to 0xffffff.
4746	* A 128K area starting from 0xd0000 works. */
4747	set_e820_range(ES, regs.u.r16.di,
4748	0x000f0000L, 0x00100000L, 0, 0, 2);
4749	#else /* !VBOX */
4750	set_e820_range(ES, regs.u.r16.di,
4751	0x000e8000L, 0x00100000L, 0, 0, 2);
4752	#endif /* !VBOX */
4753	regs.u.r32.ebx = 3;
4754	regs.u.r32.eax = 0x534D4150;
4755	regs.u.r32.ecx = 0x14;
4756	CLEAR_CF();
4757	return;
4758	break;
4759	case 3:
4760	set_e820_range(ES, regs.u.r16.di,
4761	0x00100000L,
4762	extended_memory_size - ACPI_DATA_SIZE, 0, 0, 1);
4763	regs.u.r32.ebx = 4;
4764	regs.u.r32.eax = 0x534D4150;
4765	regs.u.r32.ecx = 0x14;
4766	CLEAR_CF();
4767	return;
4768	break;
4769	case 4:
4770	set_e820_range(ES, regs.u.r16.di,
4771	extended_memory_size - ACPI_DATA_SIZE,
4772	extended_memory_size, 0, 0, 3); // ACPI RAM
4773	regs.u.r32.ebx = 5;
4774	regs.u.r32.eax = 0x534D4150;
4775	regs.u.r32.ecx = 0x14;
4776	CLEAR_CF();
4777	return;
4778	break;
4779	case 5:
4780	/* 256KB BIOS area at the end of 4 GB */
4781	set_e820_range(ES, regs.u.r16.di,
4782	0xfffc0000L, 0x00000000L, 0, 0, 2);
4783	#ifdef VBOX_WITH_MORE_THAN_4GB
4784	if (extra_highbits_memory_size \|\| extra_lowbits_memory_size)
4785	regs.u.r32.ebx = 6;
4786	else
4787	#endif
4788	regs.u.r32.ebx = 0;
4789	regs.u.r32.eax = 0x534D4150;
4790	regs.u.r32.ecx = 0x14;
4791	CLEAR_CF();
4792	return;
4793	#ifdef VBOX_WITH_MORE_THAN_4GB
4794	case 6:
4795	/* Mapping of memory above 4 GB */
4796	set_e820_range(ES, regs.u.r16.di,
4797	0x00000000L, extra_lowbits_memory_size,
4798	1, extra_highbits_memory_size + 1, 1);
4799	regs.u.r32.ebx = 0;
4800	regs.u.r32.eax = 0x534D4150;
4801	regs.u.r32.ecx = 0x14;
4802	CLEAR_CF();
4803	return;
4804	#endif
4805	default: /* AX=E820, DX=534D4150, BX unrecognized */
4806	goto int15_unimplemented;
4807	break;
4808	}
4809	} else {
4810	// if DX != 0x534D4150)
4811	goto int15_unimplemented;
4812	}
4813	break;
4814
4815	case 0x01:
4816	// do we have any reason to fail here ?
4817	CLEAR_CF();
4818
4819	// my real system sets ax and bx to 0
4820	// this is confirmed by Ralph Brown list
4821	// but syslinux v1.48 is known to behave
4822	// strangely if ax is set to 0
4823	// regs.u.r16.ax = 0;
4824	// regs.u.r16.bx = 0;
4825
4826	// Get the amount of extended memory (above 1M)
4827	regs.u.r8.cl = inb_cmos(0x30);
4828	regs.u.r8.ch = inb_cmos(0x31);
4829
4830	// limit to 15M
4831	if(regs.u.r16.cx > 0x3c00)
4832	{
4833	regs.u.r16.cx = 0x3c00;
4834	}
4835
4836	// Get the amount of extended memory above 16M in 64k blocs
4837	regs.u.r8.dl = inb_cmos(0x34);
4838	regs.u.r8.dh = inb_cmos(0x35);
4839
4840	// Set configured memory equal to extended memory
4841	regs.u.r16.ax = regs.u.r16.cx;
4842	regs.u.r16.bx = regs.u.r16.dx;
4843	break;
4844	default: /* AH=0xE8?? but not implemented */
4845	goto int15_unimplemented;
4846	}
4847	break;
4848	int15_unimplemented:
4849	// fall into the default
4850	default:
4851	BX_INFO("*** int 15h function AX=%04x, BX=%04x not yet supported!\n",
4852	(unsigned) regs.u.r16.ax, (unsigned) regs.u.r16.bx);
4853	SET_CF();
4854	regs.u.r8.ah = UNSUPPORTED_FUNCTION;
4855	break;
4856	}
4857	}
4858
4859	void
4860	int16_function(DI, SI, BP, SP, BX, DX, CX, AX, FLAGS)
4861	Bit16u DI, SI, BP, SP, BX, DX, CX, AX, FLAGS;
4862	{
4863	Bit8u scan_code, ascii_code, shift_flags, led_flags, count;
4864	Bit16u kbd_code, max;
4865
4866	BX_DEBUG_INT16("int16: AX=%04x BX=%04x CX=%04x DX=%04x \n", AX, BX, CX, DX);
4867
4868	shift_flags = read_byte(0x0040, 0x17);
4869	led_flags = read_byte(0x0040, 0x97);
4870	if ((((shift_flags >> 4) & 0x07) ^ (led_flags & 0x07)) != 0) {
4871	ASM_START
4872	cli
4873	ASM_END
4874	outb(0x60, 0xed);
4875	while ((inb(0x64) & 0x01) == 0) outb(0x80, 0x21);
4876	if ((inb(0x60) == 0xfa)) {
4877	led_flags &= 0xf8;
4878	led_flags \|= ((shift_flags >> 4) & 0x07);
4879	outb(0x60, led_flags & 0x07);
4880	while ((inb(0x64) & 0x01) == 0) outb(0x80, 0x21);
4881	inb(0x60);
4882	write_byte(0x0040, 0x97, led_flags);
4883	}
4884	ASM_START
4885	sti
4886	ASM_END
4887	}
4888
4889	switch (GET_AH()) {
4890	case 0x00: /* read keyboard input */
4891
4892	if ( !dequeue_key(&scan_code, &ascii_code, 1) ) {
4893	BX_PANIC("KBD: int16h: out of keyboard input\n");
4894	}
4895	if (scan_code !=0 && ascii_code == 0xF0) ascii_code = 0;
4896	else if (ascii_code == 0xE0) ascii_code = 0;
4897	AX = (scan_code << 8) \| ascii_code;
4898	break;
4899
4900	case 0x01: /* check keyboard status */
4901	if ( !dequeue_key(&scan_code, &ascii_code, 0) ) {
4902	SET_ZF();
4903	return;
4904	}
4905	if (scan_code !=0 && ascii_code == 0xF0) ascii_code = 0;
4906	else if (ascii_code == 0xE0) ascii_code = 0;
4907	AX = (scan_code << 8) \| ascii_code;
4908	CLEAR_ZF();
4909	break;
4910
4911	case 0x02: /* get shift flag status */
4912	shift_flags = read_byte(0x0040, 0x17);
4913	SET_AL(shift_flags);
4914	break;
4915
4916	case 0x05: /* store key-stroke into buffer */
4917	if ( !enqueue_key(GET_CH(), GET_CL()) ) {
4918	SET_AL(1);
4919	}
4920	else {
4921	SET_AL(0);
4922	}
4923	break;
4924
4925	case 0x09: /* GET KEYBOARD FUNCTIONALITY */
4926	// bit Bochs Description
4927	// 7 0 reserved
4928	// 6 0 INT 16/AH=20h-22h supported (122-key keyboard support)
4929	// 5 1 INT 16/AH=10h-12h supported (enhanced keyboard support)
4930	// 4 1 INT 16/AH=0Ah supported
4931	// 3 0 INT 16/AX=0306h supported
4932	// 2 0 INT 16/AX=0305h supported
4933	// 1 0 INT 16/AX=0304h supported
4934	// 0 0 INT 16/AX=0300h supported
4935	//
4936	SET_AL(0x30);
4937	break;
4938
4939	case 0x0A: /* GET KEYBOARD ID */
4940	count = 2;
4941	kbd_code = 0x0;
4942	outb(0x60, 0xf2);
4943	/* Wait for data */
4944	max=0xffff;
4945	while ( ((inb(0x64) & 0x01) == 0) && (--max>0) ) outb(0x80, 0x00);
4946	if (max>0x0) {
4947	if ((inb(0x60) == 0xfa)) {
4948	do {
4949	max=0xffff;
4950	while ( ((inb(0x64) & 0x01) == 0) && (--max>0) ) outb(0x80, 0x00);
4951	if (max>0x0) {
4952	kbd_code >>= 8;
4953	kbd_code \|= (inb(0x60) << 8);
4954	}
4955	} while (--count>0);
4956	}
4957	}
4958	BX=kbd_code;
4959	break;
4960
4961	case 0x10: /* read MF-II keyboard input */
4962
4963	if ( !dequeue_key(&scan_code, &ascii_code, 1) ) {
4964	BX_PANIC("KBD: int16h: out of keyboard input\n");
4965	}
4966	if (scan_code !=0 && ascii_code == 0xF0) ascii_code = 0;
4967	AX = (scan_code << 8) \| ascii_code;
4968	break;
4969
4970	case 0x11: /* check MF-II keyboard status */
4971	if ( !dequeue_key(&scan_code, &ascii_code, 0) ) {
4972	SET_ZF();
4973	return;
4974	}
4975	if (scan_code !=0 && ascii_code == 0xF0) ascii_code = 0;
4976	AX = (scan_code << 8) \| ascii_code;
4977	CLEAR_ZF();
4978	break;
4979
4980	case 0x12: /* get extended keyboard status */
4981	shift_flags = read_byte(0x0040, 0x17);
4982	SET_AL(shift_flags);
4983	shift_flags = read_byte(0x0040, 0x18) & 0x73;
4984	shift_flags \|= read_byte(0x0040, 0x96) & 0x0c;
4985	SET_AH(shift_flags);
4986	BX_DEBUG_INT16("int16: func 12 sending %04x\n",AX);
4987	break;
4988
4989	case 0x92: /* keyboard capability check called by DOS 5.0+ keyb */
4990	SET_AH(0x80); // function int16 ah=0x10-0x12 supported
4991	break;
4992
4993	case 0xA2: /* 122 keys capability check called by DOS 5.0+ keyb */
4994	// don't change AH : function int16 ah=0x20-0x22 NOT supported
4995	break;
4996
4997	case 0x6F:
4998	if (GET_AL() == 0x08)
4999	SET_AH(0x02); // unsupported, aka normal keyboard
5000
5001	default:
5002	BX_INFO("KBD: unsupported int 16h function %02x\n", GET_AH());
5003	}
5004	}
5005
5006	unsigned int
5007	dequeue_key(scan_code, ascii_code, incr)
5008	Bit8u *scan_code;
5009	Bit8u *ascii_code;
5010	unsigned int incr;
5011	{
5012	Bit16u buffer_start, buffer_end, buffer_head, buffer_tail;
5013	Bit16u ss;
5014	Bit8u acode, scode;
5015
5016	#if BX_CPU < 2
5017	buffer_start = 0x001E;
5018	buffer_end = 0x003E;
5019	#else
5020	buffer_start = read_word(0x0040, 0x0080);
5021	buffer_end = read_word(0x0040, 0x0082);
5022	#endif
5023
5024	buffer_head = read_word(0x0040, 0x001a);
5025	buffer_tail = read_word(0x0040, 0x001c);
5026
5027	if (buffer_head != buffer_tail) {
5028	ss = get_SS();
5029	acode = read_byte(0x0040, buffer_head);
5030	scode = read_byte(0x0040, buffer_head+1);
5031	write_byte(ss, ascii_code, acode);
5032	write_byte(ss, scan_code, scode);
5033
5034	if (incr) {
5035	buffer_head += 2;
5036	if (buffer_head >= buffer_end)
5037	buffer_head = buffer_start;
5038	write_word(0x0040, 0x001a, buffer_head);
5039	}
5040	return(1);
5041	}
5042	else {
5043	return(0);
5044	}
5045	}
5046
5047	static char panic_msg_keyb_buffer_full[] = "%s: keyboard input buffer full\n";
5048
5049	Bit8u
5050	send_to_mouse_ctrl(sendbyte)
5051	Bit8u sendbyte;
5052	{
5053	Bit8u response;
5054
5055	// wait for chance to write to ctrl
5056	if ( inb(0x64) & 0x02 )
5057	BX_PANIC(panic_msg_keyb_buffer_full,"sendmouse");
5058	outb(0x64, 0xD4);
5059	outb(0x60, sendbyte);
5060	return(0);
5061	}
5062
5063
5064	Bit8u
5065	get_mouse_data(data)
5066	Bit8u *data;
5067	{
5068	Bit8u response;
5069	Bit16u ss;
5070
5071	while ( (inb(0x64) & 0x21) != 0x21 ) {
5072	}
5073
5074	response = inb(0x60);
5075
5076	ss = get_SS();
5077	write_byte(ss, data, response);
5078	return(0);
5079	}
5080
5081	void
5082	set_kbd_command_byte(command_byte)
5083	Bit8u command_byte;
5084	{
5085	if ( inb(0x64) & 0x02 )
5086	BX_PANIC(panic_msg_keyb_buffer_full,"setkbdcomm");
5087
5088	outb(0x64, 0x60); // write command byte
5089	outb(0x60, command_byte);
5090	}
5091
5092	void
5093	int09_function(DI, SI, BP, SP, BX, DX, CX, AX)
5094	Bit16u DI, SI, BP, SP, BX, DX, CX, AX;
5095	{
5096	Bit8u scancode, asciicode, shift_flags;
5097	Bit8u mf2_flags, mf2_state;
5098
5099	//
5100	// DS has been set to F000 before call
5101	//
5102
5103
5104	scancode = GET_AL();
5105
5106	if (scancode == 0) {
5107	BX_INFO("KBD: int09 handler: AL=0\n");
5108	return;
5109	}
5110
5111
5112	shift_flags = read_byte(0x0040, 0x17);
5113	mf2_flags = read_byte(0x0040, 0x18);
5114	mf2_state = read_byte(0x0040, 0x96);
5115	asciicode = 0;
5116
5117	switch (scancode) {
5118	case 0x3a: /* Caps Lock press */
5119	shift_flags ^= 0x40;
5120	write_byte(0x0040, 0x17, shift_flags);
5121	mf2_flags \|= 0x40;
5122	write_byte(0x0040, 0x18, mf2_flags);
5123	break;
5124	case 0xba: /* Caps Lock release */
5125	mf2_flags &= ~0x40;
5126	write_byte(0x0040, 0x18, mf2_flags);
5127	break;
5128
5129	case 0x2a: /* L Shift press */
5130	shift_flags \|= 0x02;
5131	write_byte(0x0040, 0x17, shift_flags);
5132	break;
5133	case 0xaa: /* L Shift release */
5134	shift_flags &= ~0x02;
5135	write_byte(0x0040, 0x17, shift_flags);
5136	break;
5137
5138	case 0x36: /* R Shift press */
5139	shift_flags \|= 0x01;
5140	write_byte(0x0040, 0x17, shift_flags);
5141	break;
5142	case 0xb6: /* R Shift release */
5143	shift_flags &= ~0x01;
5144	write_byte(0x0040, 0x17, shift_flags);
5145	break;
5146
5147	case 0x1d: /* Ctrl press */
5148	if ((mf2_state & 0x01) == 0) {
5149	shift_flags \|= 0x04;
5150	write_byte(0x0040, 0x17, shift_flags);
5151	if (mf2_state & 0x02) {
5152	mf2_state \|= 0x04;
5153	write_byte(0x0040, 0x96, mf2_state);
5154	} else {
5155	mf2_flags \|= 0x01;
5156	write_byte(0x0040, 0x18, mf2_flags);
5157	}
5158	}
5159	break;
5160	case 0x9d: /* Ctrl release */
5161	if ((mf2_state & 0x01) == 0) {
5162	shift_flags &= ~0x04;
5163	write_byte(0x0040, 0x17, shift_flags);
5164	if (mf2_state & 0x02) {
5165	mf2_state &= ~0x04;
5166	write_byte(0x0040, 0x96, mf2_state);
5167	} else {
5168	mf2_flags &= ~0x01;
5169	write_byte(0x0040, 0x18, mf2_flags);
5170	}
5171	}
5172	break;
5173
5174	case 0x38: /* Alt press */
5175	shift_flags \|= 0x08;
5176	write_byte(0x0040, 0x17, shift_flags);
5177	if (mf2_state & 0x02) {
5178	mf2_state \|= 0x08;
5179	write_byte(0x0040, 0x96, mf2_state);
5180	} else {
5181	mf2_flags \|= 0x02;
5182	write_byte(0x0040, 0x18, mf2_flags);
5183	}
5184	break;
5185	case 0xb8: /* Alt release */
5186	shift_flags &= ~0x08;
5187	write_byte(0x0040, 0x17, shift_flags);
5188	if (mf2_state & 0x02) {
5189	mf2_state &= ~0x08;
5190	write_byte(0x0040, 0x96, mf2_state);
5191	} else {
5192	mf2_flags &= ~0x02;
5193	write_byte(0x0040, 0x18, mf2_flags);
5194	}
5195	break;
5196
5197	case 0x45: /* Num Lock press */
5198	if ((mf2_state & 0x03) == 0) {
5199	mf2_flags \|= 0x20;
5200	write_byte(0x0040, 0x18, mf2_flags);
5201	shift_flags ^= 0x20;
5202	write_byte(0x0040, 0x17, shift_flags);
5203	}
5204	break;
5205	case 0xc5: /* Num Lock release */
5206	if ((mf2_state & 0x03) == 0) {
5207	mf2_flags &= ~0x20;
5208	write_byte(0x0040, 0x18, mf2_flags);
5209	}
5210	break;
5211
5212	case 0x46: /* Scroll Lock press */
5213	mf2_flags \|= 0x10;
5214	write_byte(0x0040, 0x18, mf2_flags);
5215	shift_flags ^= 0x10;
5216	write_byte(0x0040, 0x17, shift_flags);
5217	break;
5218
5219	case 0xc6: /* Scroll Lock release */
5220	mf2_flags &= ~0x10;
5221	write_byte(0x0040, 0x18, mf2_flags);
5222	break;
5223
5224	default:
5225	if (scancode & 0x80) {
5226	break; /* toss key releases ... */
5227	}
5228	if (scancode > MAX_SCAN_CODE) {
5229	BX_INFO("KBD: int09h_handler(): unknown scancode read: 0x%02x!\n", scancode);
5230	return;
5231	}
5232	if (shift_flags & 0x08) { /* ALT */
5233	asciicode = scan_to_scanascii[scancode].alt;
5234	scancode = scan_to_scanascii[scancode].alt >> 8;
5235	} else if (shift_flags & 0x04) { /* CONTROL */
5236	asciicode = scan_to_scanascii[scancode].control;
5237	scancode = scan_to_scanascii[scancode].control >> 8;
5238	} else if (((mf2_state & 0x02) > 0) && ((scancode >= 0x47) && (scancode <= 0x53))) {
5239	/* extended keys handling */
5240	asciicode = 0xe0;
5241	scancode = scan_to_scanascii[scancode].normal >> 8;
5242	} else if (shift_flags & 0x03) { /* LSHIFT + RSHIFT */
5243	/* check if lock state should be ignored
5244	* because a SHIFT key are pressed */
5245
5246	if (shift_flags & scan_to_scanascii[scancode].lock_flags) {
5247	asciicode = scan_to_scanascii[scancode].normal;
5248	scancode = scan_to_scanascii[scancode].normal >> 8;
5249	} else {
5250	asciicode = scan_to_scanascii[scancode].shift;
5251	scancode = scan_to_scanascii[scancode].shift >> 8;
5252	}
5253	} else {
5254	/* check if lock is on */
5255	if (shift_flags & scan_to_scanascii[scancode].lock_flags) {
5256	asciicode = scan_to_scanascii[scancode].shift;
5257	scancode = scan_to_scanascii[scancode].shift >> 8;
5258	} else {
5259	asciicode = scan_to_scanascii[scancode].normal;
5260	scancode = scan_to_scanascii[scancode].normal >> 8;
5261	}
5262	}
5263	if (scancode==0 && asciicode==0) {
5264	BX_INFO("KBD: int09h_handler(): scancode & asciicode are zero?\n");
5265	}
5266	enqueue_key(scancode, asciicode);
5267	break;
5268	}
5269	if ((scancode & 0x7f) != 0x1d) {
5270	mf2_state &= ~0x01;
5271	}
5272	mf2_state &= ~0x02;
5273	write_byte(0x0040, 0x96, mf2_state);
5274	}
5275
5276	unsigned int
5277	enqueue_key(scan_code, ascii_code)
5278	Bit8u scan_code, ascii_code;
5279	{
5280	Bit16u buffer_start, buffer_end, buffer_head, buffer_tail, temp_tail;
5281
5282	#if BX_CPU < 2
5283	buffer_start = 0x001E;
5284	buffer_end = 0x003E;
5285	#else
5286	buffer_start = read_word(0x0040, 0x0080);
5287	buffer_end = read_word(0x0040, 0x0082);
5288	#endif
5289
5290	buffer_head = read_word(0x0040, 0x001A);
5291	buffer_tail = read_word(0x0040, 0x001C);
5292
5293	temp_tail = buffer_tail;
5294	buffer_tail += 2;
5295	if (buffer_tail >= buffer_end)
5296	buffer_tail = buffer_start;
5297
5298	if (buffer_tail == buffer_head) {
5299	return(0);
5300	}
5301
5302	write_byte(0x0040, temp_tail, ascii_code);
5303	write_byte(0x0040, temp_tail+1, scan_code);
5304	write_word(0x0040, 0x001C, buffer_tail);
5305	return(1);
5306	}
5307
5308
5309	void
5310	int74_function(make_farcall, Z, Y, X, status)
5311	Bit16u make_farcall, Z, Y, X, status;
5312	{
5313	Bit16u ebda_seg=read_word(0x0040,0x000E);
5314	Bit8u in_byte, index, package_count;
5315	Bit8u mouse_flags_1, mouse_flags_2;
5316
5317	BX_DEBUG_INT74("entering int74_function\n");
5318	make_farcall = 0;
5319
5320	in_byte = inb(0x64);
5321	if ( (in_byte & 0x21) != 0x21 ) {
5322	return;
5323	}
5324	in_byte = inb(0x60);
5325	BX_DEBUG_INT74("int74: read byte %02x\n", in_byte);
5326
5327	mouse_flags_1 = read_byte(ebda_seg, 0x0026);
5328	mouse_flags_2 = read_byte(ebda_seg, 0x0027);
5329
5330	if ( (mouse_flags_2 & 0x80) != 0x80 ) {
5331	return;
5332	}
5333
5334	package_count = mouse_flags_2 & 0x07;
5335	index = mouse_flags_1 & 0x07;
5336	write_byte(ebda_seg, 0x28 + index, in_byte);
5337
5338	if ( index >= package_count ) {
5339	BX_DEBUG_INT74("int74_function: make_farcall=1\n");
5340	status = read_byte(ebda_seg, 0x0028 + 0);
5341	X = read_byte(ebda_seg, 0x0028 + 1);
5342	Y = read_byte(ebda_seg, 0x0028 + 2);
5343	Z = 0;
5344	mouse_flags_1 = 0;
5345	// check if far call handler installed
5346	if (mouse_flags_2 & 0x80)
5347	make_farcall = 1;
5348	}
5349	else {
5350	mouse_flags_1++;
5351	}
5352	write_byte(ebda_seg, 0x0026, mouse_flags_1);
5353	}
5354
5355	#define SET_DISK_RET_STATUS(status) write_byte(0x0040, 0x0074, status)
5356
5357	#if BX_USE_ATADRV
5358
5359	void
5360	int13_harddisk(EHAX, DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS)
5361	Bit16u EHAX, DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS;
5362	{
5363	Bit32u lba;
5364	Bit16u ebda_seg=read_word(0x0040,0x000E);
5365	Bit16u cylinder, head, sector;
5366	Bit16u segment, offset;
5367	Bit16u npc, nph, npspt, nlc, nlh, nlspt;
5368	Bit16u size, count;
5369	Bit8u device, status;
5370
5371	BX_DEBUG_INT13_HD("int13_harddisk: AX=%04x BX=%04x CX=%04x DX=%04x ES=%04x\n", AX, BX, CX, DX, ES);
5372
5373	write_byte(0x0040, 0x008e, 0); // clear completion flag
5374
5375	#ifdef VBOX_WITH_SCSI
5376	// basic check : device has to be defined
5377	if ( (GET_ELDL() < 0x80) \|\| (GET_ELDL() >= 0x80 + BX_MAX_ATA_DEVICES + BX_MAX_SCSI_DEVICES) ) {
5378	BX_INFO("int13_harddisk: function %02x, ELDL out of range %02x\n", GET_AH(), GET_ELDL());
5379	goto int13_fail;
5380	}
5381	#else
5382	// basic check : device has to be defined
5383	if ( (GET_ELDL() < 0x80) \|\| (GET_ELDL() >= 0x80 + BX_MAX_ATA_DEVICES) ) {
5384	BX_INFO("int13_harddisk: function %02x, ELDL out of range %02x\n", GET_AH(), GET_ELDL());
5385	goto int13_fail;
5386	}
5387	#endif
5388
5389	// Get the ata channel
5390	device=read_byte(ebda_seg,&EbdaData->ata.hdidmap[GET_ELDL()-0x80]);
5391
5392	#ifdef VBOX_WITH_SCSI
5393	// basic check : device has to be valid
5394	if (device >= BX_MAX_ATA_DEVICES + BX_MAX_SCSI_DEVICES) {
5395	BX_INFO("int13_harddisk: function %02x, unmapped device for ELDL=%02x\n", GET_AH(), GET_ELDL());
5396	goto int13_fail;
5397	}
5398	#else
5399	// basic check : device has to be valid
5400	if (device >= BX_MAX_ATA_DEVICES) {
5401	BX_INFO("int13_harddisk: function %02x, unmapped device for ELDL=%02x\n", GET_AH(), GET_ELDL());
5402	goto int13_fail;
5403	}
5404	#endif
5405
5406	switch (GET_AH()) {
5407
5408	case 0x00: /* disk controller reset */
5409	#ifdef VBOX_WITH_SCSI
5410	/* SCSI controller does not need a reset. */
5411	if (!VBOX_IS_SCSI_DEVICE(device))
5412	#endif
5413	ata_reset (device);
5414	goto int13_success;
5415	break;
5416
5417	case 0x01: /* read disk status */
5418	status = read_byte(0x0040, 0x0074);
5419	SET_AH(status);
5420	SET_DISK_RET_STATUS(0);
5421	/* set CF if error status read */
5422	if (status) goto int13_fail_nostatus;
5423	else goto int13_success_noah;
5424	break;
5425
5426	case 0x02: // read disk sectors
5427	case 0x03: // write disk sectors
5428	case 0x04: // verify disk sectors
5429
5430	count = GET_AL();
5431	cylinder = GET_CH();
5432	cylinder \|= ( ((Bit16u) GET_CL()) << 2) & 0x300;
5433	sector = (GET_CL() & 0x3f);
5434	head = GET_DH();
5435
5436	segment = ES;
5437	offset = BX;
5438
5439	if ( (count > 128) \|\| (count == 0) ) {
5440	BX_INFO("int13_harddisk: function %02x, count out of range!\n",GET_AH());
5441	goto int13_fail;
5442	}
5443
5444	#ifdef VBOX_WITH_SCSI
5445	if (!VBOX_IS_SCSI_DEVICE(device))
5446	#endif
5447	{
5448	nlc = read_word(ebda_seg, &EbdaData->ata.devices[device].lchs.cylinders);
5449	nlh = read_word(ebda_seg, &EbdaData->ata.devices[device].lchs.heads);
5450	nlspt = read_word(ebda_seg, &EbdaData->ata.devices[device].lchs.spt);
5451	}
5452	#ifdef VBOX_WITH_SCSI
5453	else
5454	{
5455	Bit8u scsi_device = VBOX_GET_SCSI_DEVICE(device);
5456
5457	nlc = read_word(ebda_seg, &EbdaData->scsi.devices[scsi_device].device_info.lchs.cylinders);
5458	nlh = read_word(ebda_seg, &EbdaData->scsi.devices[scsi_device].device_info.lchs.heads);
5459	nlspt = read_word(ebda_seg, &EbdaData->scsi.devices[scsi_device].device_info.lchs.spt);
5460	}
5461	#endif
5462
5463	// sanity check on cyl heads, sec
5464	if( (cylinder >= nlc) \|\| (head >= nlh) \|\| (sector > nlspt )) {
5465	BX_INFO("int13_harddisk: function %02x, parameters out of range %04x/%04x/%04x!\n", GET_AH(), cylinder, head, sector);
5466	goto int13_fail;
5467	}
5468
5469	// FIXME verify
5470	if ( GET_AH() == 0x04 ) goto int13_success;
5471
5472	#ifdef VBOX_WITH_SCSI
5473	if (!VBOX_IS_SCSI_DEVICE(device))
5474	#endif
5475	{
5476	nph = read_word(ebda_seg, &EbdaData->ata.devices[device].pchs.heads);
5477	npspt = read_word(ebda_seg, &EbdaData->ata.devices[device].pchs.spt);
5478	}
5479	#ifdef VBOX_WITH_SCSI
5480	else
5481	{
5482	Bit8u scsi_device = VBOX_GET_SCSI_DEVICE(device);
5483	nph = read_word(ebda_seg, &EbdaData->scsi.devices[scsi_device].device_info.pchs.heads);
5484	npspt = read_word(ebda_seg, &EbdaData->scsi.devices[scsi_device].device_info.pchs.spt);
5485	}
5486	#endif
5487
5488	// if needed, translate lchs to lba, and execute command
5489	#ifdef VBOX_WITH_SCSI
5490	if (( (nph != nlh) \|\| (npspt != nlspt)) \|\| VBOX_IS_SCSI_DEVICE(device)) {
5491	lba = ((((Bit32u)cylinder * (Bit32u)nlh) + (Bit32u)head) * (Bit32u)nlspt) + (Bit32u)sector - 1;
5492	sector = 0; // this forces the command to be lba
5493	}
5494	#else
5495	if (( (nph != nlh) \|\| (npspt != nlspt)) ) {
5496	lba = ((((Bit32u)cylinder * (Bit32u)nlh) + (Bit32u)head) * (Bit32u)nlspt) + (Bit32u)sector - 1;
5497	sector = 0; // this forces the command to be lba
5498	}
5499	#endif
5500
5501	if ( GET_AH() == 0x02 )
5502	{
5503	#ifdef VBOX_WITH_SCSI
5504	if (VBOX_IS_SCSI_DEVICE(device))
5505	status=scsi_read_sectors(VBOX_GET_SCSI_DEVICE(device), count, lba, segment, offset);
5506	else
5507	#endif
5508	status=ata_cmd_data_in(device, ATA_CMD_READ_SECTORS, count, cylinder, head, sector, lba, segment, offset);
5509	}
5510	else
5511	{
5512	#ifdef VBOX_WITH_SCSI
5513	if (VBOX_IS_SCSI_DEVICE(device))
5514	status=scsi_write_sectors(VBOX_GET_SCSI_DEVICE(device), count, lba, segment, offset);
5515	else
5516	#endif
5517	status=ata_cmd_data_out(device, ATA_CMD_WRITE_SECTORS, count, cylinder, head, sector, lba, segment, offset);
5518	}
5519
5520	// Set nb of sector transferred
5521	SET_AL(read_word(ebda_seg, &EbdaData->ata.trsfsectors));
5522
5523	if (status != 0) {
5524	BX_INFO("int13_harddisk: function %02x, error %02x !\n",GET_AH(),status);
5525	SET_AH(0x0c);
5526	goto int13_fail_noah;
5527	}
5528
5529	goto int13_success;
5530	break;
5531
5532	case 0x05: /* format disk track */
5533	BX_INFO("format disk track called\n");
5534	goto int13_success;
5535	return;
5536	break;
5537
5538	case 0x08: /* read disk drive parameters */
5539
5540	// Get logical geometry from table
5541	nlc = read_word(ebda_seg, &EbdaData->ata.devices[device].lchs.cylinders);
5542	nlh = read_word(ebda_seg, &EbdaData->ata.devices[device].lchs.heads);
5543	nlspt = read_word(ebda_seg, &EbdaData->ata.devices[device].lchs.spt);
5544	count = read_byte(ebda_seg, &EbdaData->ata.hdcount);
5545
5546	#ifndef VBOX
5547	nlc = nlc - 2; /* 0 based , last sector not used */
5548	#else /* VBOX */
5549	/* Maximum cylinder number is just one less than the number of cylinders. */
5550	nlc = nlc - 1; /* 0 based , last sector not used */
5551	#endif /* VBOX */
5552	SET_AL(0);
5553	SET_CH(nlc & 0xff);
5554	SET_CL(((nlc >> 2) & 0xc0) \| (nlspt & 0x3f));
5555	SET_DH(nlh - 1);
5556	SET_DL(count); /* FIXME returns 0, 1, or n hard drives */
5557
5558	// FIXME should set ES & DI
5559
5560	goto int13_success;
5561	break;
5562
5563	case 0x10: /* check drive ready */
5564	// should look at 40:8E also???
5565
5566	// Read the status from controller
5567	status = inb(read_word(ebda_seg, &EbdaData->ata.channels[device/2].iobase1) + ATA_CB_STAT);
5568	if ( (status & ( ATA_CB_STAT_BSY \| ATA_CB_STAT_RDY )) == ATA_CB_STAT_RDY ) {
5569	goto int13_success;
5570	}
5571	else {
5572	SET_AH(0xAA);
5573	goto int13_fail_noah;
5574	}
5575	break;
5576
5577	case 0x15: /* read disk drive size */
5578
5579	// Get physical geometry from table
5580	npc = read_word(ebda_seg, &EbdaData->ata.devices[device].pchs.cylinders);
5581	nph = read_word(ebda_seg, &EbdaData->ata.devices[device].pchs.heads);
5582	npspt = read_word(ebda_seg, &EbdaData->ata.devices[device].pchs.spt);
5583
5584	// Compute sector count seen by int13
5585	#ifndef VBOX
5586	lba = (Bit32u)(npc - 1) * (Bit32u)nph * (Bit32u)npspt;
5587	#else /* VBOX */
5588	/* Is it so hard to multiply a couple of counts (without introducing
5589	* arbitrary off by one errors)? */
5590	lba = (Bit32u)npc * (Bit32u)nph * (Bit32u)npspt;
5591	#endif /* VBOX */
5592	CX = lba >> 16;
5593	DX = lba & 0xffff;
5594
5595	SET_AH(3); // hard disk accessible
5596	goto int13_success_noah;
5597	break;
5598
5599	case 0x41: // IBM/MS installation check
5600	BX=0xaa55; // install check
5601	SET_AH(0x30); // EDD 3.0
5602	CX=0x0007; // ext disk access and edd, removable supported
5603	goto int13_success_noah;
5604	break;
5605
5606	case 0x42: // IBM/MS extended read
5607	case 0x43: // IBM/MS extended write
5608	case 0x44: // IBM/MS verify
5609	case 0x47: // IBM/MS extended seek
5610
5611	count=read_word(DS, SI+(Bit16u)&Int13Ext->count);
5612	segment=read_word(DS, SI+(Bit16u)&Int13Ext->segment);
5613	offset=read_word(DS, SI+(Bit16u)&Int13Ext->offset);
5614
5615	// Can't use 64 bits lba
5616	lba=read_dword(DS, SI+(Bit16u)&Int13Ext->lba2);
5617	if (lba != 0L) {
5618	BX_PANIC("int13_harddisk: function %02x. Can't use 64bits lba\n",GET_AH());
5619	goto int13_fail;
5620	}
5621
5622	// Get 32 bits lba and check
5623	lba=read_dword(DS, SI+(Bit16u)&Int13Ext->lba1);
5624
5625	#ifdef VBOX_WITH_SCSI
5626	if (VBOX_IS_SCSI_DEVICE(device))
5627	{
5628	if (lba >= read_dword(ebda_seg, &EbdaData->scsi.devices[VBOX_GET_SCSI_DEVICE(device)].device_info.sectors) ) {
5629	BX_INFO("int13_harddisk: function %02x. LBA out of range\n",GET_AH());
5630	goto int13_fail;
5631	}
5632	}
5633	else
5634	#endif
5635	if (lba >= read_dword(ebda_seg, &EbdaData->ata.devices[device].sectors) ) {
5636	BX_INFO("int13_harddisk: function %02x. LBA out of range\n",GET_AH());
5637	goto int13_fail;
5638	}
5639
5640
5641	// If verify or seek
5642	if (( GET_AH() == 0x44 ) \|\| ( GET_AH() == 0x47 ))
5643	goto int13_success;
5644
5645	// Execute the command
5646	if ( GET_AH() == 0x42 )
5647	#ifdef VBOX
5648	{
5649	#ifdef VBOX_WITH_SCSI
5650	if (VBOX_IS_SCSI_DEVICE(device))
5651	status=scsi_read_sectors(VBOX_GET_SCSI_DEVICE(device), count, lba, segment, offset);
5652	else
5653	#endif
5654	{
5655	if (count >= 256 \|\| lba + count >= 268435456)
5656	status=ata_cmd_data_in(device, ATA_CMD_READ_SECTORS_EXT, count, 0, 0, 0, lba, segment, offset);
5657	else
5658	status=ata_cmd_data_in(device, ATA_CMD_READ_SECTORS, count, 0, 0, 0, lba, segment, offset);
5659	}
5660	}
5661	#else /* !VBOX */
5662	status=ata_cmd_data_in(device, ATA_CMD_READ_SECTORS, count, 0, 0, 0, lba, segment, offset);
5663	#endif /* VBOX */
5664	else
5665	#ifdef VBOX
5666	{
5667	#ifdef VBOX_WITH_SCSI
5668	if (VBOX_IS_SCSI_DEVICE(device))
5669	status=scsi_write_sectors(VBOX_GET_SCSI_DEVICE(device), count, lba, segment, offset);
5670	else
5671	#endif
5672	{
5673	if (count >= 256 \|\| lba + count >= 268435456)
5674	status=ata_cmd_data_out(device, ATA_CMD_WRITE_SECTORS_EXT, count, 0, 0, 0, lba, segment, offset);
5675	else
5676	status=ata_cmd_data_out(device, ATA_CMD_WRITE_SECTORS, count, 0, 0, 0, lba, segment, offset);
5677	}
5678	}
5679	#else /* !VBOX */
5680	status=ata_cmd_data_out(device, ATA_CMD_WRITE_SECTORS, count, 0, 0, 0, lba, segment, offset);
5681	#endif /* VBOX */
5682
5683	count=read_word(ebda_seg, &EbdaData->ata.trsfsectors);
5684	write_word(DS, SI+(Bit16u)&Int13Ext->count, count);
5685
5686	if (status != 0) {
5687	BX_INFO("int13_harddisk: function %02x, error %02x !\n",GET_AH(),status);
5688	SET_AH(0x0c);
5689	goto int13_fail_noah;
5690	}
5691
5692	goto int13_success;
5693	break;
5694
5695	case 0x45: // IBM/MS lock/unlock drive
5696	case 0x49: // IBM/MS extended media change
5697	goto int13_success; // Always success for HD
5698	break;
5699
5700	case 0x46: // IBM/MS eject media
5701	SET_AH(0xb2); // Volume Not Removable
5702	goto int13_fail_noah; // Always fail for HD
5703	break;
5704
5705	case 0x48: // IBM/MS get drive parameters
5706	size=read_word(DS,SI+(Bit16u)&Int13DPT->size);
5707
5708	// Buffer is too small
5709	if(size < 0x1a)
5710	goto int13_fail;
5711
5712	// EDD 1.x
5713	if(size >= 0x1a) {
5714	Bit16u blksize;
5715
5716	npc = read_word(ebda_seg, &EbdaData->ata.devices[device].pchs.cylinders);
5717	nph = read_word(ebda_seg, &EbdaData->ata.devices[device].pchs.heads);
5718	npspt = read_word(ebda_seg, &EbdaData->ata.devices[device].pchs.spt);
5719	lba = read_dword(ebda_seg, &EbdaData->ata.devices[device].sectors);
5720	blksize = read_word(ebda_seg, &EbdaData->ata.devices[device].blksize);
5721
5722	write_word(DS, SI+(Bit16u)&Int13DPT->size, 0x1a);
5723	write_word(DS, SI+(Bit16u)&Int13DPT->infos, 0x02); // geometry is valid
5724	write_dword(DS, SI+(Bit16u)&Int13DPT->cylinders, (Bit32u)npc);
5725	write_dword(DS, SI+(Bit16u)&Int13DPT->heads, (Bit32u)nph);
5726	write_dword(DS, SI+(Bit16u)&Int13DPT->spt, (Bit32u)npspt);
5727	write_dword(DS, SI+(Bit16u)&Int13DPT->sector_count1, lba); // FIXME should be Bit64
5728	write_dword(DS, SI+(Bit16u)&Int13DPT->sector_count2, 0L);
5729	write_word(DS, SI+(Bit16u)&Int13DPT->blksize, blksize);
5730	}
5731
5732	// EDD 2.x
5733	if(size >= 0x1e) {
5734	Bit8u channel, dev, irq, mode, checksum, i, translation;
5735	Bit16u iobase1, iobase2, options;
5736
5737	write_word(DS, SI+(Bit16u)&Int13DPT->size, 0x1e);
5738
5739	write_word(DS, SI+(Bit16u)&Int13DPT->dpte_segment, ebda_seg);
5740	write_word(DS, SI+(Bit16u)&Int13DPT->dpte_offset, &EbdaData->ata.dpte);
5741
5742	// Fill in dpte
5743	channel = device / 2;
5744	iobase1 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase1);
5745	iobase2 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase2);
5746	irq = read_byte(ebda_seg, &EbdaData->ata.channels[channel].irq);
5747	mode = read_byte(ebda_seg, &EbdaData->ata.devices[device].mode);
5748	translation = read_byte(ebda_seg, &EbdaData->ata.devices[device].translation);
5749
5750	options = (translation==ATA_TRANSLATION_NONE?0:1<<3); // chs translation
5751	options \|= (1<<4); // lba translation
5752	options \|= (mode==ATA_MODE_PIO32?1:0<<7);
5753	options \|= (translation==ATA_TRANSLATION_LBA?1:0<<9);
5754	options \|= (translation==ATA_TRANSLATION_RECHS?3:0<<9);
5755
5756	write_word(ebda_seg, &EbdaData->ata.dpte.iobase1, iobase1);
5757	write_word(ebda_seg, &EbdaData->ata.dpte.iobase2, iobase2);
5758	write_byte(ebda_seg, &EbdaData->ata.dpte.prefix, (0xe \| (device % 2))<<4 );
5759	write_byte(ebda_seg, &EbdaData->ata.dpte.unused, 0xcb );
5760	write_byte(ebda_seg, &EbdaData->ata.dpte.irq, irq );
5761	write_byte(ebda_seg, &EbdaData->ata.dpte.blkcount, 1 );
5762	write_byte(ebda_seg, &EbdaData->ata.dpte.dma, 0 );
5763	write_byte(ebda_seg, &EbdaData->ata.dpte.pio, 0 );
5764	write_word(ebda_seg, &EbdaData->ata.dpte.options, options);
5765	write_word(ebda_seg, &EbdaData->ata.dpte.reserved, 0);
5766	write_byte(ebda_seg, &EbdaData->ata.dpte.revision, 0x11);
5767
5768	checksum=0;
5769	for (i=0; i<15; i++) checksum+=read_byte(ebda_seg, (&EbdaData->ata.dpte) + i);
5770	checksum = ~checksum;
5771	write_byte(ebda_seg, &EbdaData->ata.dpte.checksum, checksum);
5772	}
5773
5774	// EDD 3.x
5775	if(size >= 0x42) {
5776	Bit8u channel, iface, checksum, i;
5777	Bit16u iobase1;
5778
5779	channel = device / 2;
5780	iface = read_byte(ebda_seg, &EbdaData->ata.channels[channel].iface);
5781	iobase1 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase1);
5782
5783	write_word(DS, SI+(Bit16u)&Int13DPT->size, 0x42);
5784	write_word(DS, SI+(Bit16u)&Int13DPT->key, 0xbedd);
5785	write_byte(DS, SI+(Bit16u)&Int13DPT->dpi_length, 0x24);
5786	write_byte(DS, SI+(Bit16u)&Int13DPT->reserved1, 0);
5787	write_word(DS, SI+(Bit16u)&Int13DPT->reserved2, 0);
5788
5789	if (iface==ATA_IFACE_ISA) {
5790	write_byte(DS, SI+(Bit16u)&Int13DPT->host_bus[0], 'I');
5791	write_byte(DS, SI+(Bit16u)&Int13DPT->host_bus[1], 'S');
5792	write_byte(DS, SI+(Bit16u)&Int13DPT->host_bus[2], 'A');
5793	write_byte(DS, SI+(Bit16u)&Int13DPT->host_bus[3], 0);
5794	}
5795	else {
5796	// FIXME PCI
5797	}
5798	write_byte(DS, SI+(Bit16u)&Int13DPT->iface_type[0], 'A');
5799	write_byte(DS, SI+(Bit16u)&Int13DPT->iface_type[1], 'T');
5800	write_byte(DS, SI+(Bit16u)&Int13DPT->iface_type[2], 'A');
5801	write_byte(DS, SI+(Bit16u)&Int13DPT->iface_type[3], 0);
5802
5803	if (iface==ATA_IFACE_ISA) {
5804	write_word(DS, SI+(Bit16u)&Int13DPT->iface_path[0], iobase1);
5805	write_word(DS, SI+(Bit16u)&Int13DPT->iface_path[2], 0);
5806	write_dword(DS, SI+(Bit16u)&Int13DPT->iface_path[4], 0L);
5807	}
5808	else {
5809	// FIXME PCI
5810	}
5811	write_byte(DS, SI+(Bit16u)&Int13DPT->device_path[0], device%2);
5812	write_byte(DS, SI+(Bit16u)&Int13DPT->device_path[1], 0);
5813	write_word(DS, SI+(Bit16u)&Int13DPT->device_path[2], 0);
5814	write_dword(DS, SI+(Bit16u)&Int13DPT->device_path[4], 0L);
5815
5816	checksum=0;
5817	for (i=30; i<64; i++) checksum+=read_byte(DS, SI + i);
5818	checksum = ~checksum;
5819	write_byte(DS, SI+(Bit16u)&Int13DPT->checksum, checksum);
5820	}
5821
5822	goto int13_success;
5823	break;
5824
5825	case 0x4e: // // IBM/MS set hardware configuration
5826	// DMA, prefetch, PIO maximum not supported
5827	switch (GET_AL()) {
5828	case 0x01:
5829	case 0x03:
5830	case 0x04:
5831	case 0x06:
5832	goto int13_success;
5833	break;
5834	default :
5835	goto int13_fail;
5836	}
5837	break;
5838
5839	case 0x09: /* initialize drive parameters */
5840	case 0x0c: /* seek to specified cylinder */
5841	case 0x0d: /* alternate disk reset */
5842	case 0x11: /* recalibrate */
5843	case 0x14: /* controller internal diagnostic */
5844	BX_INFO("int13_harddisk: function %02xh unimplemented, returns success\n", GET_AH());
5845	goto int13_success;
5846	break;
5847
5848	case 0x0a: /* read disk sectors with ECC */
5849	case 0x0b: /* write disk sectors with ECC */
5850	case 0x18: // set media type for format
5851	case 0x50: // IBM/MS send packet command
5852	default:
5853	BX_INFO("int13_harddisk: function %02xh unsupported, returns fail\n", GET_AH());
5854	goto int13_fail;
5855	break;
5856	}
5857
5858	int13_fail:
5859	SET_AH(0x01); // defaults to invalid function in AH or invalid parameter
5860	int13_fail_noah:
5861	SET_DISK_RET_STATUS(GET_AH());
5862	int13_fail_nostatus:
5863	SET_CF(); // error occurred
5864	return;
5865
5866	int13_success:
5867	SET_AH(0x00); // no error
5868	int13_success_noah:
5869	SET_DISK_RET_STATUS(0x00);
5870	CLEAR_CF(); // no error
5871	return;
5872	}
5873
5874	// ---------------------------------------------------------------------------
5875	// Start of int13 for cdrom
5876	// ---------------------------------------------------------------------------
5877
5878	void
5879	int13_cdrom(EHBX, DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS)
5880	Bit16u EHBX, DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS;
5881	{
5882	Bit16u ebda_seg=read_word(0x0040,0x000E);
5883	Bit8u device, status, locks;
5884	Bit8u atacmd[12];
5885	Bit32u lba;
5886	Bit16u count, segment, offset, i, size;
5887
5888	BX_DEBUG_INT13_CD("int13_cdrom: AX=%04x BX=%04x CX=%04x DX=%04x ES=%04x\n", AX, BX, CX, DX, ES);
5889
5890	SET_DISK_RET_STATUS(0x00);
5891
5892	/* basic check : device should be 0xE0+ */
5893	if( (GET_ELDL() < 0xE0) \|\| (GET_ELDL() >= 0xE0+BX_MAX_ATA_DEVICES) ) {
5894	BX_INFO("int13_cdrom: function %02x, ELDL out of range %02x\n", GET_AH(), GET_ELDL());
5895	goto int13_fail;
5896	}
5897
5898	// Get the ata channel
5899	device=read_byte(ebda_seg,&EbdaData->ata.cdidmap[GET_ELDL()-0xE0]);
5900
5901	/* basic check : device has to be valid */
5902	if (device >= BX_MAX_ATA_DEVICES) {
5903	BX_INFO("int13_cdrom: function %02x, unmapped device for ELDL=%02x\n", GET_AH(), GET_ELDL());
5904	goto int13_fail;
5905	}
5906
5907	switch (GET_AH()) {
5908
5909	// all those functions return SUCCESS
5910	case 0x00: /* disk controller reset */
5911	case 0x09: /* initialize drive parameters */
5912	case 0x0c: /* seek to specified cylinder */
5913	case 0x0d: /* alternate disk reset */
5914	case 0x10: /* check drive ready */
5915	case 0x11: /* recalibrate */
5916	case 0x14: /* controller internal diagnostic */
5917	case 0x16: /* detect disk change */
5918	goto int13_success;
5919	break;
5920
5921	// all those functions return disk write-protected
5922	case 0x03: /* write disk sectors */
5923	case 0x05: /* format disk track */
5924	case 0x43: // IBM/MS extended write
5925	SET_AH(0x03);
5926	goto int13_fail_noah;
5927	break;
5928
5929	case 0x01: /* read disk status */
5930	status = read_byte(0x0040, 0x0074);
5931	SET_AH(status);
5932	SET_DISK_RET_STATUS(0);
5933
5934	/* set CF if error status read */
5935	if (status) goto int13_fail_nostatus;
5936	else goto int13_success_noah;
5937	break;
5938
5939	case 0x15: /* read disk drive size */
5940	SET_AH(0x02);
5941	goto int13_fail_noah;
5942	break;
5943
5944	case 0x41: // IBM/MS installation check
5945	BX=0xaa55; // install check
5946	SET_AH(0x30); // EDD 2.1
5947	CX=0x0007; // ext disk access, removable and edd
5948	goto int13_success_noah;
5949	break;
5950
5951	case 0x42: // IBM/MS extended read
5952	case 0x44: // IBM/MS verify sectors
5953	case 0x47: // IBM/MS extended seek
5954
5955	count=read_word(DS, SI+(Bit16u)&Int13Ext->count);
5956	segment=read_word(DS, SI+(Bit16u)&Int13Ext->segment);
5957	offset=read_word(DS, SI+(Bit16u)&Int13Ext->offset);
5958
5959	// Can't use 64 bits lba
5960	lba=read_dword(DS, SI+(Bit16u)&Int13Ext->lba2);
5961	if (lba != 0L) {
5962	BX_PANIC("int13_cdrom: function %02x. Can't use 64bits lba\n",GET_AH());
5963	goto int13_fail;
5964	}
5965
5966	// Get 32 bits lba
5967	lba=read_dword(DS, SI+(Bit16u)&Int13Ext->lba1);
5968
5969	// If verify or seek
5970	if (( GET_AH() == 0x44 ) \|\| ( GET_AH() == 0x47 ))
5971	goto int13_success;
5972
5973	memsetb(get_SS(),atacmd,0,12);
5974	atacmd[0]=0x28; // READ command
5975	atacmd[7]=(count & 0xff00) >> 8; // Sectors
5976	atacmd[8]=(count & 0x00ff); // Sectors
5977	atacmd[2]=(lba & 0xff000000) >> 24; // LBA
5978	atacmd[3]=(lba & 0x00ff0000) >> 16;
5979	atacmd[4]=(lba & 0x0000ff00) >> 8;
5980	atacmd[5]=(lba & 0x000000ff);
5981	status = ata_cmd_packet(device, 12, get_SS(), atacmd, 0, count*2048L, ATA_DATA_IN, segment,offset);
5982
5983	count = (Bit16u)(read_dword(ebda_seg, &EbdaData->ata.trsfbytes) >> 11);
5984	write_word(DS, SI+(Bit16u)&Int13Ext->count, count);
5985
5986	if (status != 0) {
5987	BX_INFO("int13_cdrom: function %02x, status %02x !\n",GET_AH(),status);
5988	SET_AH(0x0c);
5989	goto int13_fail_noah;
5990	}
5991
5992	goto int13_success;
5993	break;
5994
5995	case 0x45: // IBM/MS lock/unlock drive
5996	if (GET_AL() > 2) goto int13_fail;
5997
5998	locks = read_byte(ebda_seg, &EbdaData->ata.devices[device].lock);
5999
6000	switch (GET_AL()) {
6001	case 0 : // lock
6002	if (locks == 0xff) {
6003	SET_AH(0xb4);
6004	SET_AL(1);
6005	goto int13_fail_noah;
6006	}
6007	write_byte(ebda_seg, &EbdaData->ata.devices[device].lock, ++locks);
6008	SET_AL(1);
6009	break;
6010	case 1 : // unlock
6011	if (locks == 0x00) {
6012	SET_AH(0xb0);
6013	SET_AL(0);
6014	goto int13_fail_noah;
6015	}
6016	write_byte(ebda_seg, &EbdaData->ata.devices[device].lock, --locks);
6017	SET_AL(locks==0?0:1);
6018	break;
6019	case 2 : // status
6020	SET_AL(locks==0?0:1);
6021	break;
6022	}
6023	goto int13_success;
6024	break;
6025
6026	case 0x46: // IBM/MS eject media
6027	locks = read_byte(ebda_seg, &EbdaData->ata.devices[device].lock);
6028
6029	if (locks != 0) {
6030	SET_AH(0xb1); // media locked
6031	goto int13_fail_noah;
6032	}
6033	// FIXME should handle 0x31 no media in device
6034	// FIXME should handle 0xb5 valid request failed
6035
6036	// Call removable media eject
6037	ASM_START
6038	push bp
6039	mov bp, sp
6040
6041	mov ah, #0x52
6042	int 15
6043	mov _int13_cdrom.status + 2[bp], ah
6044	jnc int13_cdrom_rme_end
6045	mov _int13_cdrom.status, #1
6046	int13_cdrom_rme_end:
6047	pop bp
6048	ASM_END
6049
6050	if (status != 0) {
6051	SET_AH(0xb1); // media locked
6052	goto int13_fail_noah;
6053	}
6054
6055	goto int13_success;
6056	break;
6057
6058	case 0x48: // IBM/MS get drive parameters
6059	size = read_word(DS,SI+(Bit16u)&Int13Ext->size);
6060
6061	// Buffer is too small
6062	if(size < 0x1a)
6063	goto int13_fail;
6064
6065	// EDD 1.x
6066	if(size >= 0x1a) {
6067	Bit16u cylinders, heads, spt, blksize;
6068
6069	blksize = read_word(ebda_seg, &EbdaData->ata.devices[device].blksize);
6070
6071	write_word(DS, SI+(Bit16u)&Int13DPT->size, 0x1a);
6072	write_word(DS, SI+(Bit16u)&Int13DPT->infos, 0x74); // removable, media change, lockable, max values
6073	write_dword(DS, SI+(Bit16u)&Int13DPT->cylinders, 0xffffffff);
6074	write_dword(DS, SI+(Bit16u)&Int13DPT->heads, 0xffffffff);
6075	write_dword(DS, SI+(Bit16u)&Int13DPT->spt, 0xffffffff);
6076	write_dword(DS, SI+(Bit16u)&Int13DPT->sector_count1, 0xffffffff); // FIXME should be Bit64
6077	write_dword(DS, SI+(Bit16u)&Int13DPT->sector_count2, 0xffffffff);
6078	write_word(DS, SI+(Bit16u)&Int13DPT->blksize, blksize);
6079	}
6080
6081	// EDD 2.x
6082	if(size >= 0x1e) {
6083	Bit8u channel, dev, irq, mode, checksum, i;
6084	Bit16u iobase1, iobase2, options;
6085
6086	write_word(DS, SI+(Bit16u)&Int13DPT->size, 0x1e);
6087
6088	write_word(DS, SI+(Bit16u)&Int13DPT->dpte_segment, ebda_seg);
6089	write_word(DS, SI+(Bit16u)&Int13DPT->dpte_offset, &EbdaData->ata.dpte);
6090
6091	// Fill in dpte
6092	channel = device / 2;
6093	iobase1 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase1);
6094	iobase2 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase2);
6095	irq = read_byte(ebda_seg, &EbdaData->ata.channels[channel].irq);
6096	mode = read_byte(ebda_seg, &EbdaData->ata.devices[device].mode);
6097
6098	// FIXME atapi device
6099	options = (1<<4); // lba translation
6100	options \|= (1<<5); // removable device
6101	options \|= (1<<6); // atapi device
6102	options \|= (mode==ATA_MODE_PIO32?1:0<<7);
6103
6104	write_word(ebda_seg, &EbdaData->ata.dpte.iobase1, iobase1);
6105	write_word(ebda_seg, &EbdaData->ata.dpte.iobase2, iobase2);
6106	write_byte(ebda_seg, &EbdaData->ata.dpte.prefix, (0xe \| (device % 2))<<4 );
6107	write_byte(ebda_seg, &EbdaData->ata.dpte.unused, 0xcb );
6108	write_byte(ebda_seg, &EbdaData->ata.dpte.irq, irq );
6109	write_byte(ebda_seg, &EbdaData->ata.dpte.blkcount, 1 );
6110	write_byte(ebda_seg, &EbdaData->ata.dpte.dma, 0 );
6111	write_byte(ebda_seg, &EbdaData->ata.dpte.pio, 0 );
6112	write_word(ebda_seg, &EbdaData->ata.dpte.options, options);
6113	write_word(ebda_seg, &EbdaData->ata.dpte.reserved, 0);
6114	write_byte(ebda_seg, &EbdaData->ata.dpte.revision, 0x11);
6115
6116	checksum=0;
6117	for (i=0; i<15; i++) checksum+=read_byte(ebda_seg, (&EbdaData->ata.dpte) + i);
6118	checksum = ~checksum;
6119	write_byte(ebda_seg, &EbdaData->ata.dpte.checksum, checksum);
6120	}
6121
6122	// EDD 3.x
6123	if(size >= 0x42) {
6124	Bit8u channel, iface, checksum, i;
6125	Bit16u iobase1;
6126
6127	channel = device / 2;
6128	iface = read_byte(ebda_seg, &EbdaData->ata.channels[channel].iface);
6129	iobase1 = read_word(ebda_seg, &EbdaData->ata.channels[channel].iobase1);
6130
6131	write_word(DS, SI+(Bit16u)&Int13DPT->size, 0x42);
6132	write_word(DS, SI+(Bit16u)&Int13DPT->key, 0xbedd);
6133	write_byte(DS, SI+(Bit16u)&Int13DPT->dpi_length, 0x24);
6134	write_byte(DS, SI+(Bit16u)&Int13DPT->reserved1, 0);
6135	write_word(DS, SI+(Bit16u)&Int13DPT->reserved2, 0);
6136
6137	if (iface==ATA_IFACE_ISA) {
6138	write_byte(DS, SI+(Bit16u)&Int13DPT->host_bus[0], 'I');
6139	write_byte(DS, SI+(Bit16u)&Int13DPT->host_bus[1], 'S');
6140	write_byte(DS, SI+(Bit16u)&Int13DPT->host_bus[2], 'A');
6141	write_byte(DS, SI+(Bit16u)&Int13DPT->host_bus[3], 0);
6142	}
6143	else {
6144	// FIXME PCI
6145	}
6146	write_byte(DS, SI+(Bit16u)&Int13DPT->iface_type[0], 'A');
6147	write_byte(DS, SI+(Bit16u)&Int13DPT->iface_type[1], 'T');
6148	write_byte(DS, SI+(Bit16u)&Int13DPT->iface_type[2], 'A');
6149	write_byte(DS, SI+(Bit16u)&Int13DPT->iface_type[3], 0);
6150
6151	if (iface==ATA_IFACE_ISA) {
6152	write_word(DS, SI+(Bit16u)&Int13DPT->iface_path[0], iobase1);
6153	write_word(DS, SI+(Bit16u)&Int13DPT->iface_path[2], 0);
6154	write_dword(DS, SI+(Bit16u)&Int13DPT->iface_path[4], 0L);
6155	}
6156	else {
6157	// FIXME PCI
6158	}
6159	write_byte(DS, SI+(Bit16u)&Int13DPT->device_path[0], device%2);
6160	write_byte(DS, SI+(Bit16u)&Int13DPT->device_path[1], 0);
6161	write_word(DS, SI+(Bit16u)&Int13DPT->device_path[2], 0);
6162	write_dword(DS, SI+(Bit16u)&Int13DPT->device_path[4], 0L);
6163
6164	checksum=0;
6165	for (i=30; i<64; i++) checksum+=read_byte(DS, SI + i);
6166	checksum = ~checksum;
6167	write_byte(DS, SI+(Bit16u)&Int13DPT->checksum, checksum);
6168	}
6169
6170	goto int13_success;
6171	break;
6172
6173	case 0x49: // IBM/MS extended media change
6174	// always send changed ??
6175	SET_AH(06);
6176	goto int13_fail_nostatus;
6177	break;
6178
6179	case 0x4e: // // IBM/MS set hardware configuration
6180	// DMA, prefetch, PIO maximum not supported
6181	switch (GET_AL()) {
6182	case 0x01:
6183	case 0x03:
6184	case 0x04:
6185	case 0x06:
6186	goto int13_success;
6187	break;
6188	default :
6189	goto int13_fail;
6190	}
6191	break;
6192
6193	// all those functions return unimplemented
6194	case 0x02: /* read sectors */
6195	case 0x04: /* verify sectors */
6196	case 0x08: /* read disk drive parameters */
6197	case 0x0a: /* read disk sectors with ECC */
6198	case 0x0b: /* write disk sectors with ECC */
6199	case 0x18: /* set media type for format */
6200	case 0x50: // ? - send packet command
6201	default:
6202	BX_INFO("int13_cdrom: unsupported AH=%02x\n", GET_AH());
6203	goto int13_fail;
6204	break;
6205	}
6206
6207	int13_fail:
6208	SET_AH(0x01); // defaults to invalid function in AH or invalid parameter
6209	int13_fail_noah:
6210	SET_DISK_RET_STATUS(GET_AH());
6211	int13_fail_nostatus:
6212	SET_CF(); // error occurred
6213	return;
6214
6215	int13_success:
6216	SET_AH(0x00); // no error
6217	int13_success_noah:
6218	SET_DISK_RET_STATUS(0x00);
6219	CLEAR_CF(); // no error
6220	return;
6221	}
6222
6223	// ---------------------------------------------------------------------------
6224	// End of int13 for cdrom
6225	// ---------------------------------------------------------------------------
6226
6227	#if BX_ELTORITO_BOOT
6228	// ---------------------------------------------------------------------------
6229	// Start of int13 for eltorito functions
6230	// ---------------------------------------------------------------------------
6231
6232	void
6233	int13_eltorito(DS, ES, DI, SI, BP, SP, BX, DX, CX, AX, IP, CS, FLAGS)
6234	Bit16u DS, ES, DI, SI, BP, SP, BX, DX, CX, AX, IP, CS, FLAGS;
6235	{
6236	Bit16u ebda_seg=read_word(0x0040,0x000E);
6237
6238	BX_DEBUG_INT13_ET("int13_eltorito: AX=%04x BX=%04x CX=%04x DX=%04x ES=%04x\n", AX, BX, CX, DX, ES);
6239	// BX_DEBUG_INT13_ET("int13_eltorito: SS=%04x DS=%04x ES=%04x DI=%04x SI=%04x\n",get_SS(), DS, ES, DI, SI);
6240
6241	switch (GET_AH()) {
6242
6243	// FIXME ElTorito Various. Should be implemented
6244	case 0x4a: // ElTorito - Initiate disk emu
6245	case 0x4c: // ElTorito - Initiate disk emu and boot
6246	case 0x4d: // ElTorito - Return Boot catalog
6247	BX_PANIC("Int13 eltorito call with AX=%04x. Please report\n",AX);
6248	goto int13_fail;
6249	break;
6250
6251	case 0x4b: // ElTorito - Terminate disk emu
6252	// FIXME ElTorito Hardcoded
6253	write_byte(DS,SI+0x00,0x13);
6254	write_byte(DS,SI+0x01,read_byte(ebda_seg,&EbdaData->cdemu.media));
6255	write_byte(DS,SI+0x02,read_byte(ebda_seg,&EbdaData->cdemu.emulated_drive));
6256	write_byte(DS,SI+0x03,read_byte(ebda_seg,&EbdaData->cdemu.controller_index));
6257	write_dword(DS,SI+0x04,read_dword(ebda_seg,&EbdaData->cdemu.ilba));
6258	write_word(DS,SI+0x08,read_word(ebda_seg,&EbdaData->cdemu.device_spec));
6259	write_word(DS,SI+0x0a,read_word(ebda_seg,&EbdaData->cdemu.buffer_segment));
6260	write_word(DS,SI+0x0c,read_word(ebda_seg,&EbdaData->cdemu.load_segment));
6261	write_word(DS,SI+0x0e,read_word(ebda_seg,&EbdaData->cdemu.sector_count));
6262	write_byte(DS,SI+0x10,read_byte(ebda_seg,&EbdaData->cdemu.vdevice.cylinders));
6263	write_byte(DS,SI+0x11,read_byte(ebda_seg,&EbdaData->cdemu.vdevice.spt));
6264	write_byte(DS,SI+0x12,read_byte(ebda_seg,&EbdaData->cdemu.vdevice.heads));
6265
6266	// If we have to terminate emulation
6267	if(GET_AL() == 0x00) {
6268	// FIXME ElTorito Various. Should be handled accordingly to spec
6269	write_byte(ebda_seg,&EbdaData->cdemu.active, 0x00); // bye bye
6270	}
6271
6272	goto int13_success;
6273	break;
6274
6275	default:
6276	BX_INFO("int13_eltorito: unsupported AH=%02x\n", GET_AH());
6277	goto int13_fail;
6278	break;
6279	}
6280
6281	int13_fail:
6282	SET_AH(0x01); // defaults to invalid function in AH or invalid parameter
6283	SET_DISK_RET_STATUS(GET_AH());
6284	SET_CF(); // error occurred
6285	return;
6286
6287	int13_success:
6288	SET_AH(0x00); // no error
6289	SET_DISK_RET_STATUS(0x00);
6290	CLEAR_CF(); // no error
6291	return;
6292	}
6293
6294	// ---------------------------------------------------------------------------
6295	// End of int13 for eltorito functions
6296	// ---------------------------------------------------------------------------
6297
6298	// ---------------------------------------------------------------------------
6299	// Start of int13 when emulating a device from the cd
6300	// ---------------------------------------------------------------------------
6301
6302	void
6303	int13_cdemu(DS, ES, DI, SI, BP, SP, BX, DX, CX, AX, IP, CS, FLAGS)
6304	Bit16u DS, ES, DI, SI, BP, SP, BX, DX, CX, AX, IP, CS, FLAGS;
6305	{
6306	Bit16u ebda_seg=read_word(0x0040,0x000E);
6307	Bit8u device, status;
6308	Bit16u vheads, vspt, vcylinders;
6309	Bit16u head, sector, cylinder, nbsectors;
6310	Bit32u vlba, ilba, slba, elba;
6311	Bit16u before, segment, offset;
6312	Bit8u atacmd[12];
6313
6314	BX_DEBUG_INT13_ET("int13_cdemu: AX=%04x BX=%04x CX=%04x DX=%04x ES=%04x\n", AX, BX, CX, DX, ES);
6315
6316	/* at this point, we are emulating a floppy/harddisk */
6317
6318	// Recompute the device number
6319	device = read_byte(ebda_seg,&EbdaData->cdemu.controller_index) * 2;
6320	device += read_byte(ebda_seg,&EbdaData->cdemu.device_spec);
6321
6322	SET_DISK_RET_STATUS(0x00);
6323
6324	/* basic checks : emulation should be active, dl should equal the emulated drive */
6325	if( (read_byte(ebda_seg,&EbdaData->cdemu.active) ==0 )
6326	\|\| (read_byte(ebda_seg,&EbdaData->cdemu.emulated_drive ) != GET_DL())) {
6327	BX_INFO("int13_cdemu: function %02x, emulation not active for DL= %02x\n", GET_AH(), GET_DL());
6328	goto int13_fail;
6329	}
6330
6331	switch (GET_AH()) {
6332
6333	// all those functions return SUCCESS
6334	case 0x00: /* disk controller reset */
6335	case 0x09: /* initialize drive parameters */
6336	case 0x0c: /* seek to specified cylinder */
6337	case 0x0d: /* alternate disk reset */ // FIXME ElTorito Various. should really reset ?
6338	case 0x10: /* check drive ready */ // FIXME ElTorito Various. should check if ready ?
6339	case 0x11: /* recalibrate */
6340	case 0x14: /* controller internal diagnostic */
6341	case 0x16: /* detect disk change */
6342	goto int13_success;
6343	break;
6344
6345	// all those functions return disk write-protected
6346	case 0x03: /* write disk sectors */
6347	case 0x05: /* format disk track */
6348	SET_AH(0x03);
6349	goto int13_fail_noah;
6350	break;
6351
6352	case 0x01: /* read disk status */
6353	status=read_byte(0x0040, 0x0074);
6354	SET_AH(status);
6355	SET_DISK_RET_STATUS(0);
6356
6357	/* set CF if error status read */
6358	if (status) goto int13_fail_nostatus;
6359	else goto int13_success_noah;
6360	break;
6361
6362	case 0x02: // read disk sectors
6363	case 0x04: // verify disk sectors
6364	vspt = read_word(ebda_seg,&EbdaData->cdemu.vdevice.spt);
6365	vcylinders = read_word(ebda_seg,&EbdaData->cdemu.vdevice.cylinders);
6366	vheads = read_word(ebda_seg,&EbdaData->cdemu.vdevice.heads);
6367
6368	ilba = read_dword(ebda_seg,&EbdaData->cdemu.ilba);
6369
6370	sector = GET_CL() & 0x003f;
6371	cylinder = (GET_CL() & 0x00c0) << 2 \| GET_CH();
6372	head = GET_DH();
6373	nbsectors = GET_AL();
6374	segment = ES;
6375	offset = BX;
6376
6377	// no sector to read ?
6378	if(nbsectors==0) goto int13_success;
6379
6380	// sanity checks sco openserver needs this!
6381	if ((sector > vspt)
6382	\|\| (cylinder >= vcylinders)
6383	\|\| (head >= vheads)) {
6384	goto int13_fail;
6385	}
6386
6387	// After controls, verify do nothing
6388	if (GET_AH() == 0x04) goto int13_success;
6389
6390	segment = ES+(BX / 16);
6391	offset = BX % 16;
6392
6393	// calculate the virtual lba inside the image
6394	vlba=((((Bit32u)cylinder(Bit32u)vheads)+(Bit32u)head)(Bit32u)vspt)+((Bit32u)(sector-1));
6395
6396	// In advance so we don't loose the count
6397	SET_AL(nbsectors);
6398
6399	// start lba on cd
6400	slba = (Bit32u)vlba/4;
6401	before= (Bit16u)vlba%4;
6402
6403	// end lba on cd
6404	elba = (Bit32u)(vlba+nbsectors-1)/4;
6405
6406	memsetb(get_SS(),atacmd,0,12);
6407	atacmd[0]=0x28; // READ command
6408	atacmd[7]=((Bit16u)(elba-slba+1) & 0xff00) >> 8; // Sectors
6409	atacmd[8]=((Bit16u)(elba-slba+1) & 0x00ff); // Sectors
6410	atacmd[2]=(ilba+slba & 0xff000000) >> 24; // LBA
6411	atacmd[3]=(ilba+slba & 0x00ff0000) >> 16;
6412	atacmd[4]=(ilba+slba & 0x0000ff00) >> 8;
6413	atacmd[5]=(ilba+slba & 0x000000ff);
6414	if((status = ata_cmd_packet(device, 12, get_SS(), atacmd, before512, nbsectors512L, ATA_DATA_IN, segment,offset)) != 0) {
6415	BX_INFO("int13_cdemu: function %02x, error %02x !\n",GET_AH(),status);
6416	SET_AH(0x02);
6417	SET_AL(0);
6418	goto int13_fail_noah;
6419	}
6420
6421	goto int13_success;
6422	break;
6423
6424	case 0x08: /* read disk drive parameters */
6425	vspt=read_word(ebda_seg,&EbdaData->cdemu.vdevice.spt);
6426	vcylinders=read_word(ebda_seg,&EbdaData->cdemu.vdevice.cylinders) - 1;
6427	vheads=read_word(ebda_seg,&EbdaData->cdemu.vdevice.heads) - 1;
6428
6429	SET_AL( 0x00 );
6430	SET_BL( 0x00 );
6431	SET_CH( vcylinders & 0xff );
6432	SET_CL((( vcylinders >> 2) & 0xc0) \| ( vspt & 0x3f ));
6433	SET_DH( vheads );
6434	SET_DL( 0x02 ); // FIXME ElTorito Various. should send the real count of drives 1 or 2
6435	// FIXME ElTorito Harddisk. should send the HD count
6436
6437	switch(read_byte(ebda_seg,&EbdaData->cdemu.media)) {
6438	case 0x01: SET_BL( 0x02 ); break;
6439	case 0x02: SET_BL( 0x04 ); break;
6440	case 0x03: SET_BL( 0x06 ); break;
6441	}
6442
6443	ASM_START
6444	push bp
6445	mov bp, sp
6446	mov ax, #diskette_param_table2
6447	mov _int13_cdemu.DI+2[bp], ax
6448	mov _int13_cdemu.ES+2[bp], cs
6449	pop bp
6450	ASM_END
6451	goto int13_success;
6452	break;
6453
6454	case 0x15: /* read disk drive size */
6455	// FIXME ElTorito Harddisk. What geometry to send ?
6456	SET_AH(0x03);
6457	goto int13_success_noah;
6458	break;
6459
6460	// all those functions return unimplemented
6461	case 0x0a: /* read disk sectors with ECC */
6462	case 0x0b: /* write disk sectors with ECC */
6463	case 0x18: /* set media type for format */
6464	case 0x41: // IBM/MS installation check
6465	// FIXME ElTorito Harddisk. Darwin would like to use EDD
6466	case 0x42: // IBM/MS extended read
6467	case 0x43: // IBM/MS extended write
6468	case 0x44: // IBM/MS verify sectors
6469	case 0x45: // IBM/MS lock/unlock drive
6470	case 0x46: // IBM/MS eject media
6471	case 0x47: // IBM/MS extended seek
6472	case 0x48: // IBM/MS get drive parameters
6473	case 0x49: // IBM/MS extended media change
6474	case 0x4e: // ? - set hardware configuration
6475	case 0x50: // ? - send packet command
6476	default:
6477	BX_INFO("int13_cdemu function AH=%02x unsupported, returns fail\n", GET_AH());
6478	goto int13_fail;
6479	break;
6480	}
6481
6482	int13_fail:
6483	SET_AH(0x01); // defaults to invalid function in AH or invalid parameter
6484	int13_fail_noah:
6485	SET_DISK_RET_STATUS(GET_AH());
6486	int13_fail_nostatus:
6487	SET_CF(); // error occurred
6488	return;
6489
6490	int13_success:
6491	SET_AH(0x00); // no error
6492	int13_success_noah:
6493	SET_DISK_RET_STATUS(0x00);
6494	CLEAR_CF(); // no error
6495	return;
6496	}
6497
6498	// ---------------------------------------------------------------------------
6499	// End of int13 when emulating a device from the cd
6500	// ---------------------------------------------------------------------------
6501
6502	#endif // BX_ELTORITO_BOOT
6503
6504	#else //BX_USE_ATADRV
6505
6506	void
6507	outLBA(cylinder,hd_heads,head,hd_sectors,sector,dl)
6508	Bit16u cylinder;
6509	Bit16u hd_heads;
6510	Bit16u head;
6511	Bit16u hd_sectors;
6512	Bit16u sector;
6513	Bit16u dl;
6514	{
6515	ASM_START
6516	push bp
6517	mov bp, sp
6518	push eax
6519	push ebx
6520	push edx
6521	xor eax,eax
6522	mov ax,4[bp] // cylinder
6523	xor ebx,ebx
6524	mov bl,6[bp] // hd_heads
6525	imul ebx
6526
6527	mov bl,8[bp] // head
6528	add eax,ebx
6529	mov bl,10[bp] // hd_sectors
6530	imul ebx
6531	mov bl,12[bp] // sector
6532	add eax,ebx
6533
6534	dec eax
6535	mov dx,#0x1f3
6536	out dx,al
6537	mov dx,#0x1f4
6538	mov al,ah
6539	out dx,al
6540	shr eax,#16
6541	mov dx,#0x1f5
6542	out dx,al
6543	and ah,#0xf
6544	mov bl,14[bp] // dl
6545	and bl,#1
6546	shl bl,#4
6547	or ah,bl
6548	or ah,#0xe0
6549	mov al,ah
6550	mov dx,#0x01f6
6551	out dx,al
6552	pop edx
6553	pop ebx
6554	pop eax
6555	pop bp
6556	ASM_END
6557	}
6558
6559	void
6560	int13_harddisk(EHAX, DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS)
6561	Bit16u EHAX, DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS;
6562	{
6563	Bit8u drive, num_sectors, sector, head, status, mod;
6564	Bit8u drive_map;
6565	Bit8u n_drives;
6566	Bit16u cyl_mod, ax;
6567	Bit16u max_cylinder, cylinder, total_sectors;
6568	Bit16u hd_cylinders;
6569	Bit8u hd_heads, hd_sectors;
6570	Bit16u val16;
6571	Bit8u sector_count;
6572	unsigned int i;
6573	Bit16u tempbx;
6574	Bit16u dpsize;
6575
6576	Bit16u count, segment, offset;
6577	Bit32u lba;
6578	Bit16u error;
6579
6580	BX_DEBUG_INT13_HD("int13 harddisk: AX=%04x BX=%04x CX=%04x DX=%04x ES=%04x\n", AX, BX, CX, DX, ES);
6581
6582	write_byte(0x0040, 0x008e, 0); // clear completion flag
6583
6584	/* at this point, DL is >= 0x80 to be passed from the floppy int13h
6585	handler code */
6586	/* check how many disks first (cmos reg 0x12), return an error if
6587	drive not present */
6588	drive_map = inb_cmos(0x12);
6589	drive_map = (((drive_map & 0xf0)==0) ? 0 : 1) \|
6590	(((drive_map & 0x0f)==0) ? 0 : 2);
6591	n_drives = (drive_map==0) ? 0 :
6592	((drive_map==3) ? 2 : 1);
6593
6594	if (!(drive_map & (1<<(GET_ELDL()&0x7f)))) { /* allow 0, 1, or 2 disks */
6595	SET_AH(0x01);
6596	SET_DISK_RET_STATUS(0x01);
6597	SET_CF(); /* error occurred */
6598	return;
6599	}
6600
6601	switch (GET_AH()) {
6602
6603	case 0x00: /* disk controller reset */
6604	BX_DEBUG_INT13_HD("int13_f00\n");
6605
6606	SET_AH(0);
6607	SET_DISK_RET_STATUS(0);
6608	set_diskette_ret_status(0);
6609	set_diskette_current_cyl(0, 0); /* current cylinder, diskette 1 */
6610	set_diskette_current_cyl(1, 0); /* current cylinder, diskette 2 */
6611	CLEAR_CF(); /* successful */
6612	return;
6613	break;
6614
6615	case 0x01: /* read disk status */
6616	BX_DEBUG_INT13_HD("int13_f01\n");
6617	status = read_byte(0x0040, 0x0074);
6618	SET_AH(status);
6619	SET_DISK_RET_STATUS(0);
6620	/* set CF if error status read */
6621	if (status) SET_CF();
6622	else CLEAR_CF();
6623	return;
6624	break;
6625
6626	case 0x04: // verify disk sectors
6627	case 0x02: // read disk sectors
6628	drive = GET_ELDL();
6629	get_hd_geometry(drive, &hd_cylinders, &hd_heads, &hd_sectors);
6630
6631	num_sectors = GET_AL();
6632	cylinder = (GET_CL() & 0x00c0) << 2 \| GET_CH();
6633	sector = (GET_CL() & 0x3f);
6634	head = GET_DH();
6635
6636
6637	if (hd_cylinders > 1024) {
6638	if (hd_cylinders <= 2048) {
6639	cylinder <<= 1;
6640	}
6641	else if (hd_cylinders <= 4096) {
6642	cylinder <<= 2;
6643	}
6644	else if (hd_cylinders <= 8192) {
6645	cylinder <<= 3;
6646	}
6647	else { // hd_cylinders <= 16384
6648	cylinder <<= 4;
6649	}
6650
6651	ax = head / hd_heads;
6652	cyl_mod = ax & 0xff;
6653	head = ax >> 8;
6654	cylinder \|= cyl_mod;
6655	}
6656
6657	if ( (cylinder >= hd_cylinders) \|\|
6658	(sector > hd_sectors) \|\|
6659	(head >= hd_heads) ) {
6660	SET_AH(1);
6661	SET_DISK_RET_STATUS(1);
6662	SET_CF(); /* error occurred */
6663	return;
6664	}
6665
6666	if ( (num_sectors > 128) \|\| (num_sectors == 0) )
6667	BX_PANIC("int13_harddisk: num_sectors out of range!\n");
6668
6669	if (head > 15)
6670	BX_PANIC("hard drive BIOS:(read/verify) head > 15\n");
6671
6672	if ( GET_AH() == 0x04 ) {
6673	SET_AH(0);
6674	SET_DISK_RET_STATUS(0);
6675	CLEAR_CF();
6676	return;
6677	}
6678
6679	status = inb(0x1f7);
6680	if (status & 0x80) {
6681	BX_PANIC("hard drive BIOS:(read/verify) BUSY bit set\n");
6682	}
6683	outb(0x01f2, num_sectors);
6684	/* activate LBA? (tomv) */
6685	if (hd_heads > 16) {
6686	BX_DEBUG_INT13_HD("CHS: %x %x %x\n", cylinder, head, sector);
6687	outLBA(cylinder,hd_heads,head,hd_sectors,sector,drive);
6688	}
6689	else {
6690	outb(0x01f3, sector);
6691	outb(0x01f4, cylinder & 0x00ff);
6692	outb(0x01f5, cylinder >> 8);
6693	outb(0x01f6, 0xa0 \| ((drive & 0x01)<<4) \| (head & 0x0f));
6694	}
6695	outb(0x01f7, 0x20);
6696
6697	while (1) {
6698	status = inb(0x1f7);
6699	if ( !(status & 0x80) ) break;
6700	}
6701
6702	if (status & 0x01) {
6703	BX_PANIC("hard drive BIOS:(read/verify) read error\n");
6704	} else if ( !(status & 0x08) ) {
6705	BX_DEBUG_INT13_HD("status was %02x\n", (unsigned) status);
6706	BX_PANIC("hard drive BIOS:(read/verify) expected DRQ=1\n");
6707	}
6708
6709	sector_count = 0;
6710	tempbx = BX;
6711
6712	ASM_START
6713	sti ;; enable higher priority interrupts
6714	ASM_END
6715
6716	while (1) {
6717	ASM_START
6718	;; store temp bx in real DI register
6719	push bp
6720	mov bp, sp
6721	mov di, _int13_harddisk.tempbx + 2 [bp]
6722	pop bp
6723
6724	;; adjust if there will be an overrun
6725	cmp di, #0xfe00
6726	jbe i13_f02_no_adjust
6727	i13_f02_adjust:
6728	sub di, #0x0200 ; sub 512 bytes from offset
6729	mov ax, es
6730	add ax, #0x0020 ; add 512 to segment
6731	mov es, ax
6732
6733	i13_f02_no_adjust:
6734	mov cx, #0x0100 ;; counter (256 words = 512b)
6735	mov dx, #0x01f0 ;; AT data read port
6736
6737	rep
6738	insw ;; CX words transfered from port(DX) to ES:[DI]
6739
6740	i13_f02_done:
6741	;; store real DI register back to temp bx
6742	push bp
6743	mov bp, sp
6744	mov _int13_harddisk.tempbx + 2 [bp], di
6745	pop bp
6746	ASM_END
6747
6748	sector_count++;
6749	num_sectors--;
6750	if (num_sectors == 0) {
6751	status = inb(0x1f7);
6752	if ( (status & 0xc9) != 0x40 )
6753	BX_PANIC("no sectors left to read/verify, status is %02x\n", (unsigned) status);
6754	break;
6755	}
6756	else {
6757	status = inb(0x1f7);
6758	if ( (status & 0xc9) != 0x48 )
6759	BX_PANIC("more sectors left to read/verify, status is %02x\n", (unsigned) status);
6760	continue;
6761	}
6762	}
6763
6764	SET_AH(0);
6765	SET_DISK_RET_STATUS(0);
6766	SET_AL(sector_count);
6767	CLEAR_CF(); /* successful */
6768	return;
6769	break;
6770
6771
6772	case 0x03: /* write disk sectors */
6773	BX_DEBUG_INT13_HD("int13_f03\n");
6774	drive = GET_ELDL ();
6775	get_hd_geometry(drive, &hd_cylinders, &hd_heads, &hd_sectors);
6776
6777	num_sectors = GET_AL();
6778	cylinder = GET_CH();
6779	cylinder \|= ( ((Bit16u) GET_CL()) << 2) & 0x300;
6780	sector = (GET_CL() & 0x3f);
6781	head = GET_DH();
6782
6783	if (hd_cylinders > 1024) {
6784	if (hd_cylinders <= 2048) {
6785	cylinder <<= 1;
6786	}
6787	else if (hd_cylinders <= 4096) {
6788	cylinder <<= 2;
6789	}
6790	else if (hd_cylinders <= 8192) {
6791	cylinder <<= 3;
6792	}
6793	else { // hd_cylinders <= 16384
6794	cylinder <<= 4;
6795	}
6796
6797	ax = head / hd_heads;
6798	cyl_mod = ax & 0xff;
6799	head = ax >> 8;
6800	cylinder \|= cyl_mod;
6801	}
6802
6803	if ( (cylinder >= hd_cylinders) \|\|
6804	(sector > hd_sectors) \|\|
6805	(head >= hd_heads) ) {
6806	SET_AH( 1);
6807	SET_DISK_RET_STATUS(1);
6808	SET_CF(); /* error occurred */
6809	return;
6810	}
6811
6812	if ( (num_sectors > 128) \|\| (num_sectors == 0) )
6813	BX_PANIC("int13_harddisk: num_sectors out of range!\n");
6814
6815	if (head > 15)
6816	BX_PANIC("hard drive BIOS:(read) head > 15\n");
6817
6818	status = inb(0x1f7);
6819	if (status & 0x80) {
6820	BX_PANIC("hard drive BIOS:(read) BUSY bit set\n");
6821	}
6822	// should check for Drive Ready Bit also in status reg
6823	outb(0x01f2, num_sectors);
6824
6825	/* activate LBA? (tomv) */
6826	if (hd_heads > 16) {
6827	BX_DEBUG_INT13_HD("CHS (write): %x %x %x\n", cylinder, head, sector);
6828	outLBA(cylinder,hd_heads,head,hd_sectors,sector,GET_ELDL());
6829	}
6830	else {
6831	outb(0x01f3, sector);
6832	outb(0x01f4, cylinder & 0x00ff);
6833	outb(0x01f5, cylinder >> 8);
6834	outb(0x01f6, 0xa0 \| ((GET_ELDL() & 0x01)<<4) \| (head & 0x0f));
6835	}
6836	outb(0x01f7, 0x30);
6837
6838	// wait for busy bit to turn off after seeking
6839	while (1) {
6840	status = inb(0x1f7);
6841	if ( !(status & 0x80) ) break;
6842	}
6843
6844	if ( !(status & 0x08) ) {
6845	BX_DEBUG_INT13_HD("status was %02x\n", (unsigned) status);
6846	BX_PANIC("hard drive BIOS:(write) data-request bit not set\n");
6847	}
6848
6849	sector_count = 0;
6850	tempbx = BX;
6851
6852	ASM_START
6853	sti ;; enable higher priority interrupts
6854	ASM_END
6855
6856	while (1) {
6857	ASM_START
6858	;; store temp bx in real SI register
6859	push bp
6860	mov bp, sp
6861	mov si, _int13_harddisk.tempbx + 2 [bp]
6862	pop bp
6863
6864	;; adjust if there will be an overrun
6865	cmp si, #0xfe00
6866	jbe i13_f03_no_adjust
6867	i13_f03_adjust:
6868	sub si, #0x0200 ; sub 512 bytes from offset
6869	mov ax, es
6870	add ax, #0x0020 ; add 512 to segment
6871	mov es, ax
6872
6873	i13_f03_no_adjust:
6874	mov cx, #0x0100 ;; counter (256 words = 512b)
6875	mov dx, #0x01f0 ;; AT data read port
6876
6877	seg ES
6878	rep
6879	outsw ;; CX words tranfered from ES:[SI] to port(DX)
6880
6881	;; store real SI register back to temp bx
6882	push bp
6883	mov bp, sp
6884	mov _int13_harddisk.tempbx + 2 [bp], si
6885	pop bp
6886	ASM_END
6887
6888	sector_count++;
6889	num_sectors--;
6890	if (num_sectors == 0) {
6891	status = inb(0x1f7);
6892	if ( (status & 0xe9) != 0x40 )
6893	BX_PANIC("no sectors left to write, status is %02x\n", (unsigned) status);
6894	break;
6895	}
6896	else {
6897	status = inb(0x1f7);
6898	if ( (status & 0xc9) != 0x48 )
6899	BX_PANIC("more sectors left to write, status is %02x\n", (unsigned) status);
6900	continue;
6901	}
6902	}
6903
6904	SET_AH(0);
6905	SET_DISK_RET_STATUS(0);
6906	SET_AL(sector_count);
6907	CLEAR_CF(); /* successful */
6908	return;
6909	break;
6910
6911	case 0x05: /* format disk track */
6912	BX_DEBUG_INT13_HD("int13_f05\n");
6913	BX_PANIC("format disk track called\n");
6914	/* nop */
6915	SET_AH(0);
6916	SET_DISK_RET_STATUS(0);
6917	CLEAR_CF(); /* successful */
6918	return;
6919	break;
6920
6921	case 0x08: /* read disk drive parameters */
6922	BX_DEBUG_INT13_HD("int13_f08\n");
6923
6924	drive = GET_ELDL ();
6925	get_hd_geometry(drive, &hd_cylinders, &hd_heads, &hd_sectors);
6926
6927	// translate CHS
6928	//
6929	if (hd_cylinders <= 1024) {
6930	// hd_cylinders >>= 0;
6931	// hd_heads <<= 0;
6932	}
6933	else if (hd_cylinders <= 2048) {
6934	hd_cylinders >>= 1;
6935	hd_heads <<= 1;
6936	}
6937	else if (hd_cylinders <= 4096) {
6938	hd_cylinders >>= 2;
6939	hd_heads <<= 2;
6940	}
6941	else if (hd_cylinders <= 8192) {
6942	hd_cylinders >>= 3;
6943	hd_heads <<= 3;
6944	}
6945	else { // hd_cylinders <= 16384
6946	hd_cylinders >>= 4;
6947	hd_heads <<= 4;
6948	}
6949
6950	max_cylinder = hd_cylinders - 2; /* 0 based */
6951	SET_AL(0);
6952	SET_CH(max_cylinder & 0xff);
6953	SET_CL(((max_cylinder >> 2) & 0xc0) \| (hd_sectors & 0x3f));
6954	SET_DH(hd_heads - 1);
6955	SET_DL(n_drives); /* returns 0, 1, or 2 hard drives */
6956	SET_AH(0);
6957	SET_DISK_RET_STATUS(0);
6958	CLEAR_CF(); /* successful */
6959
6960	return;
6961	break;
6962
6963	case 0x09: /* initialize drive parameters */
6964	BX_DEBUG_INT13_HD("int13_f09\n");
6965	SET_AH(0);
6966	SET_DISK_RET_STATUS(0);
6967	CLEAR_CF(); /* successful */
6968	return;
6969	break;
6970
6971	case 0x0a: /* read disk sectors with ECC */
6972	BX_DEBUG_INT13_HD("int13_f0a\n");
6973	case 0x0b: /* write disk sectors with ECC */
6974	BX_DEBUG_INT13_HD("int13_f0b\n");
6975	BX_PANIC("int13h Functions 0Ah & 0Bh not implemented!\n");
6976	return;
6977	break;
6978
6979	case 0x0c: /* seek to specified cylinder */
6980	BX_DEBUG_INT13_HD("int13_f0c\n");
6981	BX_INFO("int13h function 0ch (seek) not implemented!\n");
6982	SET_AH(0);
6983	SET_DISK_RET_STATUS(0);
6984	CLEAR_CF(); /* successful */
6985	return;
6986	break;
6987
6988	case 0x0d: /* alternate disk reset */
6989	BX_DEBUG_INT13_HD("int13_f0d\n");
6990	SET_AH(0);
6991	SET_DISK_RET_STATUS(0);
6992	CLEAR_CF(); /* successful */
6993	return;
6994	break;
6995
6996	case 0x10: /* check drive ready */
6997	BX_DEBUG_INT13_HD("int13_f10\n");
6998	//SET_AH(0);
6999	//SET_DISK_RET_STATUS(0);
7000	//CLEAR_CF(); /* successful */
7001	//return;
7002	//break;
7003
7004	// should look at 40:8E also???
7005	status = inb(0x01f7);
7006	if ( (status & 0xc0) == 0x40 ) {
7007	SET_AH(0);
7008	SET_DISK_RET_STATUS(0);
7009	CLEAR_CF(); // drive ready
7010	return;
7011	}
7012	else {
7013	SET_AH(0xAA);
7014	SET_DISK_RET_STATUS(0xAA);
7015	SET_CF(); // not ready
7016	return;
7017	}
7018	break;
7019
7020	case 0x11: /* recalibrate */
7021	BX_DEBUG_INT13_HD("int13_f11\n");
7022	SET_AH(0);
7023	SET_DISK_RET_STATUS(0);
7024	CLEAR_CF(); /* successful */
7025	return;
7026	break;
7027
7028	case 0x14: /* controller internal diagnostic */
7029	BX_DEBUG_INT13_HD("int13_f14\n");
7030	SET_AH(0);
7031	SET_DISK_RET_STATUS(0);
7032	CLEAR_CF(); /* successful */
7033	SET_AL(0);
7034	return;
7035	break;
7036
7037	case 0x15: /* read disk drive size */
7038	drive = GET_ELDL();
7039	get_hd_geometry(drive, &hd_cylinders, &hd_heads, &hd_sectors);
7040	ASM_START
7041	push bp
7042	mov bp, sp
7043	mov al, _int13_harddisk.hd_heads + 2 [bp]
7044	mov ah, _int13_harddisk.hd_sectors + 2 [bp]
7045	mul al, ah ;; ax = heads * sectors
7046	mov bx, _int13_harddisk.hd_cylinders + 2 [bp]
7047	dec bx ;; use (cylinders - 1) ???
7048	mul ax, bx ;; dx:ax = (cylinders -1) * (heads * sectors)
7049	;; now we need to move the 32bit result dx:ax to what the
7050	;; BIOS wants which is cx:dx.
7051	;; and then into CX:DX on the stack
7052	mov _int13_harddisk.CX + 2 [bp], dx
7053	mov _int13_harddisk.DX + 2 [bp], ax
7054	pop bp
7055	ASM_END
7056	SET_AH(3); // hard disk accessible
7057	SET_DISK_RET_STATUS(0); // ??? should this be 0
7058	CLEAR_CF(); // successful
7059	return;
7060	break;
7061
7062	case 0x18: // set media type for format
7063	case 0x41: // IBM/MS
7064	case 0x42: // IBM/MS
7065	case 0x43: // IBM/MS
7066	case 0x44: // IBM/MS
7067	case 0x45: // IBM/MS lock/unlock drive
7068	case 0x46: // IBM/MS eject media
7069	case 0x47: // IBM/MS extended seek
7070	case 0x49: // IBM/MS extended media change
7071	case 0x50: // IBM/MS send packet command
7072	default:
7073	BX_INFO("int13_harddisk: unsupported AH=%02x\n", GET_AH());
7074
7075	SET_AH(1); // code=invalid function in AH or invalid parameter
7076	SET_DISK_RET_STATUS(1);
7077	SET_CF(); /* unsuccessful */
7078	return;
7079	break;
7080	}
7081	}
7082
7083	static char panic_msg_reg12h[] = "HD%d cmos reg 12h not type F\n";
7084	static char panic_msg_reg19h[] = "HD%d cmos reg %02xh not user definable type 47\n";
7085
7086	void
7087	get_hd_geometry(drive, hd_cylinders, hd_heads, hd_sectors)
7088	Bit8u drive;
7089	Bit16u *hd_cylinders;
7090	Bit8u *hd_heads;
7091	Bit8u *hd_sectors;
7092	{
7093	Bit8u hd_type;
7094	Bit16u ss;
7095	Bit16u cylinders;
7096	Bit8u iobase;
7097
7098	ss = get_SS();
7099	if (drive == 0x80) {
7100	hd_type = inb_cmos(0x12) & 0xf0;
7101	if (hd_type != 0xf0)
7102	BX_INFO(panic_msg_reg12h,0);
7103	hd_type = inb_cmos(0x19); // HD0: extended type
7104	if (hd_type != 47)
7105	BX_INFO(panic_msg_reg19h,0,0x19);
7106	iobase = 0x1b;
7107	} else {
7108	hd_type = inb_cmos(0x12) & 0x0f;
7109	if (hd_type != 0x0f)
7110	BX_INFO(panic_msg_reg12h,1);
7111	hd_type = inb_cmos(0x1a); // HD0: extended type
7112	if (hd_type != 47)
7113	BX_INFO(panic_msg_reg19h,0,0x1a);
7114	iobase = 0x24;
7115	}
7116
7117	// cylinders
7118	cylinders = inb_cmos(iobase) \| (inb_cmos(iobase+1) << 8);
7119	write_word(ss, hd_cylinders, cylinders);
7120
7121	// heads
7122	write_byte(ss, hd_heads, inb_cmos(iobase+2));
7123
7124	// sectors per track
7125	write_byte(ss, hd_sectors, inb_cmos(iobase+8));
7126	}
7127
7128	#endif //else BX_USE_ATADRV
7129
7130
7131	//////////////////////
7132	// FLOPPY functions //
7133	//////////////////////
7134
7135	void floppy_reset_controller()
7136	{
7137	Bit8u val8;
7138
7139	// Reset controller
7140	val8 = inb(0x03f2);
7141	outb(0x03f2, val8 & ~0x04);
7142	outb(0x03f2, val8 \| 0x04);
7143
7144	// Wait for controller to come out of reset
7145	do {
7146	val8 = inb(0x3f4);
7147	} while ( (val8 & 0xc0) != 0x80 );
7148	}
7149
7150	void floppy_prepare_controller(drive)
7151	Bit16u drive;
7152	{
7153	Bit8u val8, dor, prev_reset;
7154
7155	// set 40:3e bit 7 to 0
7156	val8 = read_byte(0x0040, 0x003e);
7157	val8 &= 0x7f;
7158	write_byte(0x0040, 0x003e, val8);
7159
7160	// turn on motor of selected drive, DMA & int enabled, normal operation
7161	prev_reset = inb(0x03f2) & 0x04;
7162	if (drive)
7163	dor = 0x20;
7164	else
7165	dor = 0x10;
7166	dor \|= 0x0c;
7167	dor \|= drive;
7168	outb(0x03f2, dor);
7169
7170	// reset the disk motor timeout value of INT 08
7171	write_byte(0x40,0x40, BX_FLOPPY_ON_CNT);
7172
7173	#ifdef VBOX
7174	// program data rate
7175	val8 = read_byte(0x0040, 0x008b);
7176	val8 >>= 6;
7177	outb(0x03f7, val8);
7178	#endif
7179
7180	// wait for drive readiness
7181	do {
7182	val8 = inb(0x3f4);
7183	} while ( (val8 & 0xc0) != 0x80 );
7184
7185	if (prev_reset == 0) {
7186	// turn on interrupts
7187	ASM_START
7188	sti
7189	ASM_END
7190	// wait on 40:3e bit 7 to become 1
7191	do {
7192	val8 = read_byte(0x0040, 0x003e);
7193	} while ( (val8 & 0x80) == 0 );
7194	val8 &= 0x7f;
7195	ASM_START
7196	cli
7197	ASM_END
7198	write_byte(0x0040, 0x003e, val8);
7199	}
7200	}
7201
7202	bx_bool
7203	floppy_media_known(drive)
7204	Bit16u drive;
7205	{
7206	Bit8u val8;
7207	Bit16u media_state_offset;
7208
7209	val8 = read_byte(0x0040, 0x003e); // diskette recal status
7210	if (drive)
7211	val8 >>= 1;
7212	val8 &= 0x01;
7213	if (val8 == 0)
7214	return(0);
7215
7216	media_state_offset = 0x0090;
7217	if (drive)
7218	media_state_offset += 1;
7219
7220	val8 = read_byte(0x0040, media_state_offset);
7221	val8 = (val8 >> 4) & 0x01;
7222	if (val8 == 0)
7223	return(0);
7224
7225	// check pass, return KNOWN
7226	return(1);
7227	}
7228
7229	bx_bool
7230	floppy_media_sense(drive)
7231	Bit16u drive;
7232	{
7233	bx_bool retval;
7234	Bit16u media_state_offset;
7235	Bit8u drive_type, config_data, media_state;
7236
7237	if (floppy_drive_recal(drive) == 0) {
7238	return(0);
7239	}
7240
7241	// for now cheat and get drive type from CMOS,
7242	// assume media is same as drive type
7243
7244	// config_data
7245	// Bitfields for diskette media control:
7246	// Bit(s) Description (Table M0028)
7247	// 7-6 last data rate set by controller
7248	// 00=500kbps, 01=300kbps, 10=250kbps, 11=1Mbps
7249	// 5-4 last diskette drive step rate selected
7250	// 00=0Ch, 01=0Dh, 10=0Eh, 11=0Ah
7251	// 3-2 {data rate at start of operation}
7252	// 1-0 reserved
7253
7254	// media_state
7255	// Bitfields for diskette drive media state:
7256	// Bit(s) Description (Table M0030)
7257	// 7-6 data rate
7258	// 00=500kbps, 01=300kbps, 10=250kbps, 11=1Mbps
7259	// 5 double stepping required (e.g. 360kB in 1.2MB)
7260	// 4 media type established
7261	// 3 drive capable of supporting 4MB media
7262	// 2-0 on exit from BIOS, contains
7263	// 000 trying 360kB in 360kB
7264	// 001 trying 360kB in 1.2MB
7265	// 010 trying 1.2MB in 1.2MB
7266	// 011 360kB in 360kB established
7267	// 100 360kB in 1.2MB established
7268	// 101 1.2MB in 1.2MB established
7269	// 110 reserved
7270	// 111 all other formats/drives
7271
7272	drive_type = inb_cmos(0x10);
7273	if (drive == 0)
7274	drive_type >>= 4;
7275	else
7276	drive_type &= 0x0f;
7277	if ( drive_type == 1 ) {
7278	// 360K 5.25" drive
7279	config_data = 0x00; // 0000 0000
7280	media_state = 0x25; // 0010 0101
7281	retval = 1;
7282	}
7283	else if ( drive_type == 2 ) {
7284	// 1.2 MB 5.25" drive
7285	config_data = 0x00; // 0000 0000
7286	media_state = 0x25; // 0010 0101 // need double stepping??? (bit 5)
7287	retval = 1;
7288	}
7289	else if ( drive_type == 3 ) {
7290	// 720K 3.5" drive
7291	config_data = 0x00; // 0000 0000 ???
7292	media_state = 0x17; // 0001 0111
7293	retval = 1;
7294	}
7295	else if ( drive_type == 4 ) {
7296	// 1.44 MB 3.5" drive
7297	config_data = 0x00; // 0000 0000
7298	media_state = 0x17; // 0001 0111
7299	retval = 1;
7300	}
7301	else if ( drive_type == 5 ) {
7302	// 2.88 MB 3.5" drive
7303	config_data = 0xCC; // 1100 1100
7304	media_state = 0xD7; // 1101 0111
7305	retval = 1;
7306	}
7307	//
7308	// Extended floppy size uses special cmos setting
7309	else if ( drive_type == 6 ) {
7310	// 160k 5.25" drive
7311	config_data = 0x00; // 0000 0000
7312	media_state = 0x27; // 0010 0111
7313	retval = 1;
7314	}
7315	else if ( drive_type == 7 ) {
7316	// 180k 5.25" drive
7317	config_data = 0x00; // 0000 0000
7318	media_state = 0x27; // 0010 0111
7319	retval = 1;
7320	}
7321	else if ( drive_type == 8 ) {
7322	// 320k 5.25" drive
7323	config_data = 0x00; // 0000 0000
7324	media_state = 0x27; // 0010 0111
7325	retval = 1;
7326	}
7327
7328	else {
7329	// not recognized
7330	config_data = 0x00; // 0000 0000
7331	media_state = 0x00; // 0000 0000
7332	retval = 0;
7333	}
7334
7335	if (drive == 0)
7336	media_state_offset = 0x90;
7337	else
7338	media_state_offset = 0x91;
7339	write_byte(0x0040, 0x008B, config_data);
7340	write_byte(0x0040, media_state_offset, media_state);
7341
7342	return(retval);
7343	}
7344
7345	bx_bool
7346	floppy_drive_recal(drive)
7347	Bit16u drive;
7348	{
7349	Bit8u val8;
7350	Bit16u curr_cyl_offset;
7351
7352	floppy_prepare_controller(drive);
7353
7354	// send Recalibrate command (2 bytes) to controller
7355	outb(0x03f5, 0x07); // 07: Recalibrate
7356	outb(0x03f5, drive); // 0=drive0, 1=drive1
7357
7358	// turn on interrupts
7359	ASM_START
7360	sti
7361	ASM_END
7362
7363	// wait on 40:3e bit 7 to become 1
7364	do {
7365	val8 = (read_byte(0x0040, 0x003e) & 0x80);
7366	} while ( val8 == 0 );
7367
7368	val8 = 0; // separate asm from while() loop
7369	// turn off interrupts
7370	ASM_START
7371	cli
7372	ASM_END
7373
7374	// set 40:3e bit 7 to 0, and calibrated bit
7375	val8 = read_byte(0x0040, 0x003e);
7376	val8 &= 0x7f;
7377	if (drive) {
7378	val8 \|= 0x02; // Drive 1 calibrated
7379	curr_cyl_offset = 0x0095;
7380	} else {
7381	val8 \|= 0x01; // Drive 0 calibrated
7382	curr_cyl_offset = 0x0094;
7383	}
7384	write_byte(0x0040, 0x003e, val8);
7385	write_byte(0x0040, curr_cyl_offset, 0); // current cylinder is 0
7386
7387	return(1);
7388	}
7389
7390
7391
7392	bx_bool
7393	floppy_drive_exists(drive)
7394	Bit16u drive;
7395	{
7396	Bit8u drive_type;
7397
7398	// check CMOS to see if drive exists
7399	drive_type = inb_cmos(0x10);
7400	if (drive == 0)
7401	drive_type >>= 4;
7402	else
7403	drive_type &= 0x0f;
7404	if ( drive_type == 0 )
7405	return(0);
7406	else
7407	return(1);
7408	}
7409
7410	#if BX_SUPPORT_FLOPPY
7411	void
7412	int13_diskette_function(DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS)
7413	Bit16u DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS;
7414	{
7415	Bit8u drive, num_sectors, track, sector, head, status;
7416	Bit16u base_address, base_count, base_es;
7417	Bit8u page, mode_register, val8, dor;
7418	Bit8u return_status[7];
7419	Bit8u drive_type, num_floppies, ah;
7420	Bit16u es, last_addr;
7421
7422	BX_DEBUG_INT13_FL("int13_diskette: AX=%04x BX=%04x CX=%04x DX=%04x ES=%04x\n", AX, BX, CX, DX, ES);
7423
7424	ah = GET_AH();
7425
7426	switch ( ah ) {
7427	case 0x00: // diskette controller reset
7428	BX_DEBUG_INT13_FL("floppy f00\n");
7429	drive = GET_ELDL();
7430	if (drive > 1) {
7431	SET_AH(1); // invalid param
7432	set_diskette_ret_status(1);
7433	SET_CF();
7434	return;
7435	}
7436	drive_type = inb_cmos(0x10);
7437
7438	if (drive == 0)
7439	drive_type >>= 4;
7440	else
7441	drive_type &= 0x0f;
7442	if (drive_type == 0) {
7443	SET_AH(0x80); // drive not responding
7444	set_diskette_ret_status(0x80);
7445	SET_CF();
7446	return;
7447	}
7448	SET_AH(0);
7449	set_diskette_ret_status(0);
7450	CLEAR_CF(); // successful
7451	set_diskette_current_cyl(drive, 0); // current cylinder
7452	return;
7453
7454	case 0x01: // Read Diskette Status
7455	CLEAR_CF();
7456	val8 = read_byte(0x0000, 0x0441);
7457	SET_AH(val8);
7458	if (val8) {
7459	SET_CF();
7460	}
7461	return;
7462
7463	case 0x02: // Read Diskette Sectors
7464	case 0x03: // Write Diskette Sectors
7465	case 0x04: // Verify Diskette Sectors
7466	num_sectors = GET_AL();
7467	track = GET_CH();
7468	sector = GET_CL();
7469	head = GET_DH();
7470	drive = GET_ELDL();
7471
7472	if ( (drive > 1) \|\| (head > 1) \|\|
7473	(num_sectors == 0) \|\| (num_sectors > 72) ) {
7474	BX_INFO("floppy: drive>1 \|\| head>1 ...\n");
7475	SET_AH(1);
7476	set_diskette_ret_status(1);
7477	SET_AL(0); // no sectors read
7478	SET_CF(); // error occurred
7479	return;
7480	}
7481
7482	// see if drive exists
7483	if (floppy_drive_exists(drive) == 0) {
7484	SET_AH(0x80); // not responding
7485	set_diskette_ret_status(0x80);
7486	SET_AL(0); // no sectors read
7487	SET_CF(); // error occurred
7488	return;
7489	}
7490
7491	// see if media in drive, and type is known
7492	if (floppy_media_known(drive) == 0) {
7493	if (floppy_media_sense(drive) == 0) {
7494	SET_AH(0x0C); // Media type not found
7495	set_diskette_ret_status(0x0C);
7496	SET_AL(0); // no sectors read
7497	SET_CF(); // error occurred
7498	return;
7499	}
7500	}
7501
7502	if (ah == 0x02) {
7503	// Read Diskette Sectors
7504
7505	//-----------------------------------
7506	// set up DMA controller for transfer
7507	//-----------------------------------
7508
7509	// es:bx = pointer to where to place information from diskette
7510	// port 04: DMA-1 base and current address, channel 2
7511	// port 05: DMA-1 base and current count, channel 2
7512	page = (ES >> 12); // upper 4 bits
7513	base_es = (ES << 4); // lower 16bits contributed by ES
7514	base_address = base_es + BX; // lower 16 bits of address
7515	// contributed by ES:BX
7516	if ( base_address < base_es ) {
7517	// in case of carry, adjust page by 1
7518	page++;
7519	}
7520	base_count = (num_sectors * 512) - 1;
7521
7522	// check for 64K boundary overrun
7523	last_addr = base_address + base_count;
7524	if (last_addr < base_address) {
7525	SET_AH(0x09);
7526	set_diskette_ret_status(0x09);
7527	SET_AL(0); // no sectors read
7528	SET_CF(); // error occurred
7529	return;
7530	}
7531
7532	BX_DEBUG_INT13_FL("masking DMA-1 c2\n");
7533	outb(0x000a, 0x06);
7534
7535	BX_DEBUG_INT13_FL("clear flip-flop\n");
7536	outb(0x000c, 0x00); // clear flip-flop
7537	outb(0x0004, base_address);
7538	outb(0x0004, base_address>>8);
7539	BX_DEBUG_INT13_FL("clear flip-flop\n");
7540	outb(0x000c, 0x00); // clear flip-flop
7541	outb(0x0005, base_count);
7542	outb(0x0005, base_count>>8);
7543
7544	// port 0b: DMA-1 Mode Register
7545	mode_register = 0x46; // single mode, increment, autoinit disable,
7546	// transfer type=write, channel 2
7547	BX_DEBUG_INT13_FL("setting mode register\n");
7548	outb(0x000b, mode_register);
7549
7550	BX_DEBUG_INT13_FL("setting page register\n");
7551	// port 81: DMA-1 Page Register, channel 2
7552	outb(0x0081, page);
7553
7554	BX_DEBUG_INT13_FL("unmask chan 2\n");
7555	outb(0x000a, 0x02); // unmask channel 2
7556
7557	BX_DEBUG_INT13_FL("unmasking DMA-1 c2\n");
7558	outb(0x000a, 0x02);
7559
7560	//--------------------------------------
7561	// set up floppy controller for transfer
7562	//--------------------------------------
7563	floppy_prepare_controller(drive);
7564
7565	// send read-normal-data command (9 bytes) to controller
7566	outb(0x03f5, 0xe6); // e6: read normal data
7567	outb(0x03f5, (head << 2) \| drive); // HD DR1 DR2
7568	outb(0x03f5, track);
7569	outb(0x03f5, head);
7570	outb(0x03f5, sector);
7571	outb(0x03f5, 2); // 512 byte sector size
7572	outb(0x03f5, sector + num_sectors - 1); // last sector to read on track
7573	outb(0x03f5, 0); // Gap length
7574	outb(0x03f5, 0xff); // Gap length
7575
7576	// turn on interrupts
7577	ASM_START
7578	sti
7579	ASM_END
7580
7581	// wait on 40:3e bit 7 to become 1
7582	do {
7583	val8 = read_byte(0x0040, 0x0040);
7584	if (val8 == 0) {
7585	floppy_reset_controller();
7586	SET_AH(0x80); // drive not ready (timeout)
7587	set_diskette_ret_status(0x80);
7588	SET_AL(0); // no sectors read
7589	SET_CF(); // error occurred
7590	return;
7591	}
7592	val8 = (read_byte(0x0040, 0x003e) & 0x80);
7593	} while ( val8 == 0 );
7594
7595	val8 = 0; // separate asm from while() loop
7596	// turn off interrupts
7597	ASM_START
7598	cli
7599	ASM_END
7600
7601	// set 40:3e bit 7 to 0
7602	val8 = read_byte(0x0040, 0x003e);
7603	val8 &= 0x7f;
7604	write_byte(0x0040, 0x003e, val8);
7605
7606	// check port 3f4 for accessibility to status bytes
7607	val8 = inb(0x3f4);
7608	if ( (val8 & 0xc0) != 0xc0 )
7609	BX_PANIC("int13_diskette: ctrl not ready\n");
7610
7611	// read 7 return status bytes from controller
7612	// using loop index broken, have to unroll...
7613	return_status[0] = inb(0x3f5);
7614	return_status[1] = inb(0x3f5);
7615	return_status[2] = inb(0x3f5);
7616	return_status[3] = inb(0x3f5);
7617	return_status[4] = inb(0x3f5);
7618	return_status[5] = inb(0x3f5);
7619	return_status[6] = inb(0x3f5);
7620	// record in BIOS Data Area
7621	write_byte(0x0040, 0x0042, return_status[0]);
7622	write_byte(0x0040, 0x0043, return_status[1]);
7623	write_byte(0x0040, 0x0044, return_status[2]);
7624	write_byte(0x0040, 0x0045, return_status[3]);
7625	write_byte(0x0040, 0x0046, return_status[4]);
7626	write_byte(0x0040, 0x0047, return_status[5]);
7627	write_byte(0x0040, 0x0048, return_status[6]);
7628
7629	if ( (return_status[0] & 0xc0) != 0 ) {
7630	SET_AH(0x20);
7631	set_diskette_ret_status(0x20);
7632	SET_AL(0); // no sectors read
7633	SET_CF(); // error occurred
7634	return;
7635	}
7636
7637	// ??? should track be new val from return_status[3] ?
7638	set_diskette_current_cyl(drive, track);
7639	// AL = number of sectors read (same value as passed)
7640	SET_AH(0x00); // success
7641	CLEAR_CF(); // success
7642	return;
7643	} else if (ah == 0x03) {
7644	// Write Diskette Sectors
7645
7646	//-----------------------------------
7647	// set up DMA controller for transfer
7648	//-----------------------------------
7649
7650	// es:bx = pointer to where to place information from diskette
7651	// port 04: DMA-1 base and current address, channel 2
7652	// port 05: DMA-1 base and current count, channel 2
7653	page = (ES >> 12); // upper 4 bits
7654	base_es = (ES << 4); // lower 16bits contributed by ES
7655	base_address = base_es + BX; // lower 16 bits of address
7656	// contributed by ES:BX
7657	if ( base_address < base_es ) {
7658	// in case of carry, adjust page by 1
7659	page++;
7660	}
7661	base_count = (num_sectors * 512) - 1;
7662
7663	// check for 64K boundary overrun
7664	last_addr = base_address + base_count;
7665	if (last_addr < base_address) {
7666	SET_AH(0x09);
7667	set_diskette_ret_status(0x09);
7668	SET_AL(0); // no sectors read
7669	SET_CF(); // error occurred
7670	return;
7671	}
7672
7673	BX_DEBUG_INT13_FL("masking DMA-1 c2\n");
7674	outb(0x000a, 0x06);
7675
7676	outb(0x000c, 0x00); // clear flip-flop
7677	outb(0x0004, base_address);
7678	outb(0x0004, base_address>>8);
7679	outb(0x000c, 0x00); // clear flip-flop
7680	outb(0x0005, base_count);
7681	outb(0x0005, base_count>>8);
7682
7683	// port 0b: DMA-1 Mode Register
7684	mode_register = 0x4a; // single mode, increment, autoinit disable,
7685	// transfer type=read, channel 2
7686	outb(0x000b, mode_register);
7687
7688	// port 81: DMA-1 Page Register, channel 2
7689	outb(0x0081, page);
7690
7691	BX_DEBUG_INT13_FL("unmasking DMA-1 c2\n");
7692	outb(0x000a, 0x02);
7693
7694	//--------------------------------------
7695	// set up floppy controller for transfer
7696	//--------------------------------------
7697	floppy_prepare_controller(drive);
7698
7699	// send write-normal-data command (9 bytes) to controller
7700	outb(0x03f5, 0xc5); // c5: write normal data
7701	outb(0x03f5, (head << 2) \| drive); // HD DR1 DR2
7702	outb(0x03f5, track);
7703	outb(0x03f5, head);
7704	outb(0x03f5, sector);
7705	outb(0x03f5, 2); // 512 byte sector size
7706	outb(0x03f5, sector + num_sectors - 1); // last sector to write on track
7707	outb(0x03f5, 0); // Gap length
7708	outb(0x03f5, 0xff); // Gap length
7709
7710	// turn on interrupts
7711	ASM_START
7712	sti
7713	ASM_END
7714
7715	// wait on 40:3e bit 7 to become 1
7716	do {
7717	val8 = read_byte(0x0040, 0x0040);
7718	if (val8 == 0) {
7719	floppy_reset_controller();
7720	SET_AH(0x80); // drive not ready (timeout)
7721	set_diskette_ret_status(0x80);
7722	SET_AL(0); // no sectors written
7723	SET_CF(); // error occurred
7724	return;
7725	}
7726	val8 = (read_byte(0x0040, 0x003e) & 0x80);
7727	} while ( val8 == 0 );
7728
7729	val8 = 0; // separate asm from while() loop
7730	// turn off interrupts
7731	ASM_START
7732	cli
7733	ASM_END
7734
7735	// set 40:3e bit 7 to 0
7736	val8 = read_byte(0x0040, 0x003e);
7737	val8 &= 0x7f;
7738	write_byte(0x0040, 0x003e, val8);
7739
7740	// check port 3f4 for accessibility to status bytes
7741	val8 = inb(0x3f4);
7742	if ( (val8 & 0xc0) != 0xc0 )
7743	BX_PANIC("int13_diskette: ctrl not ready\n");
7744
7745	// read 7 return status bytes from controller
7746	// using loop index broken, have to unroll...
7747	return_status[0] = inb(0x3f5);
7748	return_status[1] = inb(0x3f5);
7749	return_status[2] = inb(0x3f5);
7750	return_status[3] = inb(0x3f5);
7751	return_status[4] = inb(0x3f5);
7752	return_status[5] = inb(0x3f5);
7753	return_status[6] = inb(0x3f5);
7754	// record in BIOS Data Area
7755	write_byte(0x0040, 0x0042, return_status[0]);
7756	write_byte(0x0040, 0x0043, return_status[1]);
7757	write_byte(0x0040, 0x0044, return_status[2]);
7758	write_byte(0x0040, 0x0045, return_status[3]);
7759	write_byte(0x0040, 0x0046, return_status[4]);
7760	write_byte(0x0040, 0x0047, return_status[5]);
7761	write_byte(0x0040, 0x0048, return_status[6]);
7762
7763	if ( (return_status[0] & 0xc0) != 0 ) {
7764	if ( (return_status[1] & 0x02) != 0 ) {
7765	// diskette not writable.
7766	// AH=status code=0x03 (tried to write on write-protected disk)
7767	// AL=number of sectors written=0
7768	AX = 0x0300;
7769	SET_CF();
7770	return;
7771	} else {
7772	BX_PANIC("int13_diskette_function: read error\n");
7773	}
7774	}
7775
7776	// ??? should track be new val from return_status[3] ?
7777	set_diskette_current_cyl(drive, track);
7778	// AL = number of sectors read (same value as passed)
7779	SET_AH(0x00); // success
7780	CLEAR_CF(); // success
7781	return;
7782	} else { // if (ah == 0x04)
7783	// Verify Diskette Sectors
7784
7785	// ??? should track be new val from return_status[3] ?
7786	set_diskette_current_cyl(drive, track);
7787	// AL = number of sectors verified (same value as passed)
7788	CLEAR_CF(); // success
7789	SET_AH(0x00); // success
7790	return;
7791	}
7792	break;
7793
7794	case 0x05: // format diskette track
7795	BX_DEBUG_INT13_FL("floppy f05\n");
7796
7797	num_sectors = GET_AL();
7798	track = GET_CH();
7799	head = GET_DH();
7800	drive = GET_ELDL();
7801
7802	if ((drive > 1) \|\| (head > 1) \|\| (track > 79) \|\|
7803	(num_sectors == 0) \|\| (num_sectors > 18)) {
7804	SET_AH(1);
7805	set_diskette_ret_status(1);
7806	SET_CF(); // error occurred
7807	}
7808
7809	// see if drive exists
7810	if (floppy_drive_exists(drive) == 0) {
7811	SET_AH(0x80); // drive not responding
7812	set_diskette_ret_status(0x80);
7813	SET_CF(); // error occurred
7814	return;
7815	}
7816
7817	// see if media in drive, and type is known
7818	if (floppy_media_known(drive) == 0) {
7819	if (floppy_media_sense(drive) == 0) {
7820	SET_AH(0x0C); // Media type not found
7821	set_diskette_ret_status(0x0C);
7822	SET_AL(0); // no sectors read
7823	SET_CF(); // error occurred
7824	return;
7825	}
7826	}
7827
7828	// set up DMA controller for transfer
7829	page = (ES >> 12); // upper 4 bits
7830	base_es = (ES << 4); // lower 16bits contributed by ES
7831	base_address = base_es + BX; // lower 16 bits of address
7832	// contributed by ES:BX
7833	if ( base_address < base_es ) {
7834	// in case of carry, adjust page by 1
7835	page++;
7836	}
7837	base_count = (num_sectors * 4) - 1;
7838
7839	// check for 64K boundary overrun
7840	last_addr = base_address + base_count;
7841	if (last_addr < base_address) {
7842	SET_AH(0x09);
7843	set_diskette_ret_status(0x09);
7844	SET_AL(0); // no sectors read
7845	SET_CF(); // error occurred
7846	return;
7847	}
7848
7849	outb(0x000a, 0x06);
7850	outb(0x000c, 0x00); // clear flip-flop
7851	outb(0x0004, base_address);
7852	outb(0x0004, base_address>>8);
7853	outb(0x000c, 0x00); // clear flip-flop
7854	outb(0x0005, base_count);
7855	outb(0x0005, base_count>>8);
7856	mode_register = 0x4a; // single mode, increment, autoinit disable,
7857	// transfer type=read, channel 2
7858	outb(0x000b, mode_register);
7859	// port 81: DMA-1 Page Register, channel 2
7860	outb(0x0081, page);
7861	outb(0x000a, 0x02);
7862
7863	// set up floppy controller for transfer
7864	floppy_prepare_controller(drive);
7865
7866	// send format-track command (6 bytes) to controller
7867	outb(0x03f5, 0x4d); // 4d: format track
7868	outb(0x03f5, (head << 2) \| drive); // HD DR1 DR2
7869	outb(0x03f5, 2); // 512 byte sector size
7870	outb(0x03f5, num_sectors); // number of sectors per track
7871	outb(0x03f5, 0); // Gap length
7872	outb(0x03f5, 0xf6); // Fill byte
7873	// turn on interrupts
7874	ASM_START
7875	sti
7876	ASM_END
7877
7878	// wait on 40:3e bit 7 to become 1
7879	do {
7880	val8 = read_byte(0x0040, 0x0040);
7881	if (val8 == 0) {
7882	floppy_reset_controller();
7883	SET_AH(0x80); // drive not ready (timeout)
7884	set_diskette_ret_status(0x80);
7885	SET_CF(); // error occurred
7886	return;
7887	}
7888	val8 = (read_byte(0x0040, 0x003e) & 0x80);
7889	} while ( val8 == 0 );
7890
7891	val8 = 0; // separate asm from while() loop
7892	// turn off interrupts
7893	ASM_START
7894	cli
7895	ASM_END
7896	// set 40:3e bit 7 to 0
7897	val8 = read_byte(0x0040, 0x003e);
7898	val8 &= 0x7f;
7899	write_byte(0x0040, 0x003e, val8);
7900	// check port 3f4 for accessibility to status bytes
7901	val8 = inb(0x3f4);
7902	if ( (val8 & 0xc0) != 0xc0 )
7903	BX_PANIC("int13_diskette: ctrl not ready\n");
7904
7905	// read 7 return status bytes from controller
7906	// using loop index broken, have to unroll...
7907	return_status[0] = inb(0x3f5);
7908	return_status[1] = inb(0x3f5);
7909	return_status[2] = inb(0x3f5);
7910	return_status[3] = inb(0x3f5);
7911	return_status[4] = inb(0x3f5);
7912	return_status[5] = inb(0x3f5);
7913	return_status[6] = inb(0x3f5);
7914	// record in BIOS Data Area
7915	write_byte(0x0040, 0x0042, return_status[0]);
7916	write_byte(0x0040, 0x0043, return_status[1]);
7917	write_byte(0x0040, 0x0044, return_status[2]);
7918	write_byte(0x0040, 0x0045, return_status[3]);
7919	write_byte(0x0040, 0x0046, return_status[4]);
7920	write_byte(0x0040, 0x0047, return_status[5]);
7921	write_byte(0x0040, 0x0048, return_status[6]);
7922
7923	if ( (return_status[0] & 0xc0) != 0 ) {
7924	if ( (return_status[1] & 0x02) != 0 ) {
7925	// diskette not writable.
7926	// AH=status code=0x03 (tried to write on write-protected disk)
7927	// AL=number of sectors written=0
7928	AX = 0x0300;
7929	SET_CF();
7930	return;
7931	} else {
7932	BX_PANIC("int13_diskette_function: write error\n");
7933	}
7934	}
7935
7936	SET_AH(0);
7937	set_diskette_ret_status(0);
7938	set_diskette_current_cyl(drive, 0);
7939	CLEAR_CF(); // successful
7940	return;
7941
7942
7943	case 0x08: // read diskette drive parameters
7944	BX_DEBUG_INT13_FL("floppy f08\n");
7945	drive = GET_ELDL();
7946
7947	if (drive > 1) {
7948	AX = 0;
7949	BX = 0;
7950	CX = 0;
7951	DX = 0;
7952	ES = 0;
7953	DI = 0;
7954	SET_DL(num_floppies);
7955	SET_CF();
7956	return;
7957	}
7958
7959	drive_type = inb_cmos(0x10);
7960	num_floppies = 0;
7961	if (drive_type & 0xf0)
7962	num_floppies++;
7963	if (drive_type & 0x0f)
7964	num_floppies++;
7965
7966	if (drive == 0)
7967	drive_type >>= 4;
7968	else
7969	drive_type &= 0x0f;
7970
7971	SET_BH(0);
7972	SET_BL(drive_type);
7973	SET_AH(0);
7974	SET_AL(0);
7975	SET_DL(num_floppies);
7976
7977	switch (drive_type) {
7978	case 0: // none
7979	CX = 0;
7980	SET_DH(0); // max head #
7981	break;
7982
7983	case 1: // 360KB, 5.25"
7984	CX = 0x2709; // 40 tracks, 9 sectors
7985	SET_DH(1); // max head #
7986	break;
7987
7988	case 2: // 1.2MB, 5.25"
7989	CX = 0x4f0f; // 80 tracks, 15 sectors
7990	SET_DH(1); // max head #
7991	break;
7992
7993	case 3: // 720KB, 3.5"
7994	CX = 0x4f09; // 80 tracks, 9 sectors
7995	SET_DH(1); // max head #
7996	break;
7997
7998	case 4: // 1.44MB, 3.5"
7999	CX = 0x4f12; // 80 tracks, 18 sectors
8000	SET_DH(1); // max head #
8001	break;
8002
8003	case 5: // 2.88MB, 3.5"
8004	CX = 0x4f24; // 80 tracks, 36 sectors
8005	SET_DH(1); // max head #
8006	break;
8007
8008	case 6: // 160k, 5.25"
8009	CX = 0x2708; // 40 tracks, 8 sectors
8010	SET_DH(0); // max head #
8011	break;
8012
8013	case 7: // 180k, 5.25"
8014	CX = 0x2709; // 40 tracks, 9 sectors
8015	SET_DH(0); // max head #
8016	break;
8017
8018	case 8: // 320k, 5.25"
8019	CX = 0x2708; // 40 tracks, 8 sectors
8020	SET_DH(1); // max head #
8021	break;
8022
8023	default: // ?
8024	BX_PANIC("floppy: int13: bad floppy type\n");
8025	}
8026
8027	/* set es & di to point to 11 byte diskette param table in ROM */
8028	ASM_START
8029	push bp
8030	mov bp, sp
8031	mov ax, #diskette_param_table2
8032	mov _int13_diskette_function.DI+2[bp], ax
8033	mov _int13_diskette_function.ES+2[bp], cs
8034	pop bp
8035	ASM_END
8036	CLEAR_CF(); // success
8037	/* disk status not changed upon success */
8038	return;
8039
8040
8041	case 0x15: // read diskette drive type
8042	BX_DEBUG_INT13_FL("floppy f15\n");
8043	drive = GET_ELDL();
8044	if (drive > 1) {
8045	SET_AH(0); // only 2 drives supported
8046	// set_diskette_ret_status here ???
8047	SET_CF();
8048	return;
8049	}
8050	drive_type = inb_cmos(0x10);
8051
8052	if (drive == 0)
8053	drive_type >>= 4;
8054	else
8055	drive_type &= 0x0f;
8056	CLEAR_CF(); // successful, not present
8057	if (drive_type==0) {
8058	SET_AH(0); // drive not present
8059	}
8060	else {
8061	SET_AH(1); // drive present, does not support change line
8062	}
8063
8064	return;
8065
8066	case 0x16: // get diskette change line status
8067	BX_DEBUG_INT13_FL("floppy f16\n");
8068	drive = GET_ELDL();
8069	if (drive > 1) {
8070	SET_AH(0x01); // invalid drive
8071	set_diskette_ret_status(0x01);
8072	SET_CF();
8073	return;
8074	}
8075
8076	SET_AH(0x06); // change line not supported
8077	set_diskette_ret_status(0x06);
8078	SET_CF();
8079	return;
8080
8081	case 0x17: // set diskette type for format(old)
8082	BX_DEBUG_INT13_FL("floppy f17\n");
8083	/* not used for 1.44M floppies */
8084	SET_AH(0x01); // not supported
8085	set_diskette_ret_status(1); /* not supported */
8086	SET_CF();
8087	return;
8088
8089	case 0x18: // set diskette type for format(new)
8090	BX_DEBUG_INT13_FL("floppy f18\n");
8091	SET_AH(0x01); // do later
8092	set_diskette_ret_status(1);
8093	SET_CF();
8094	return;
8095
8096	default:
8097	BX_INFO("int13_diskette: unsupported AH=%02x\n", GET_AH());
8098
8099	// if ( (ah==0x20) \|\| ((ah>=0x41) && (ah<=0x49)) \|\| (ah==0x4e) ) {
8100	SET_AH(0x01); // ???
8101	set_diskette_ret_status(1);
8102	SET_CF();
8103	return;
8104	// }
8105	}
8106	}
8107	#else // #if BX_SUPPORT_FLOPPY
8108	void
8109	int13_diskette_function(DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS)
8110	Bit16u DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS;
8111	{
8112	Bit8u val8;
8113
8114	switch ( GET_AH() ) {
8115
8116	case 0x01: // Read Diskette Status
8117	CLEAR_CF();
8118	val8 = read_byte(0x0000, 0x0441);
8119	SET_AH(val8);
8120	if (val8) {
8121	SET_CF();
8122	}
8123	return;
8124
8125	default:
8126	SET_CF();
8127	write_byte(0x0000, 0x0441, 0x01);
8128	SET_AH(0x01);
8129	}
8130	}
8131	#endif // #if BX_SUPPORT_FLOPPY
8132
8133	void
8134	set_diskette_ret_status(value)
8135	Bit8u value;
8136	{
8137	write_byte(0x0040, 0x0041, value);
8138	}
8139
8140	void
8141	set_diskette_current_cyl(drive, cyl)
8142	Bit8u drive;
8143	Bit8u cyl;
8144	{
8145	if (drive > 1)
8146	BX_PANIC("set_diskette_current_cyl(): drive > 1\n");
8147	write_byte(0x0040, 0x0094+drive, cyl);
8148	}
8149
8150	void
8151	determine_floppy_media(drive)
8152	Bit16u drive;
8153	{
8154	#if 0
8155	Bit8u val8, DOR, ctrl_info;
8156
8157	ctrl_info = read_byte(0x0040, 0x008F);
8158	if (drive==1)
8159	ctrl_info >>= 4;
8160	else
8161	ctrl_info &= 0x0f;
8162
8163	#if 0
8164	if (drive == 0) {
8165	DOR = 0x1c; // DOR: drive0 motor on, DMA&int enabled, normal op, drive select 0
8166	}
8167	else {
8168	DOR = 0x2d; // DOR: drive1 motor on, DMA&int enabled, normal op, drive select 1
8169	}
8170	#endif
8171
8172	if ( (ctrl_info & 0x04) != 0x04 ) {
8173	// Drive not determined means no drive exists, done.
8174	return;
8175	}
8176
8177	#if 0
8178	// check Main Status Register for readiness
8179	val8 = inb(0x03f4) & 0x80; // Main Status Register
8180	if (val8 != 0x80)
8181	BX_PANIC("d_f_m: MRQ bit not set\n");
8182
8183	// change line
8184
8185	// existing BDA values
8186
8187	// turn on drive motor
8188	outb(0x03f2, DOR); // Digital Output Register
8189	//
8190	#endif
8191	BX_PANIC("d_f_m: OK so far\n");
8192	#endif
8193	}
8194
8195	void
8196	int17_function(regs, ds, iret_addr)
8197	pusha_regs_t regs; // regs pushed from PUSHA instruction
8198	Bit16u ds; // previous DS:, DS set to 0x0000 by asm wrapper
8199	iret_addr_t iret_addr; // CS,IP,Flags pushed from original INT call
8200	{
8201	Bit16u addr,timeout;
8202	Bit8u val8;
8203
8204	ASM_START
8205	sti
8206	ASM_END
8207
8208	addr = read_word(0x0040, (regs.u.r16.dx << 1) + 8);
8209	if ((regs.u.r8.ah < 3) && (regs.u.r16.dx < 3) && (addr > 0)) {
8210	timeout = read_byte(0x0040, 0x0078 + regs.u.r16.dx) << 8;
8211	if (regs.u.r8.ah == 0) {
8212	outb(addr, regs.u.r8.al);
8213	val8 = inb(addr+2);
8214	outb(addr+2, val8 \| 0x01); // send strobe
8215	ASM_START
8216	nop
8217	ASM_END
8218	outb(addr+2, val8 & ~0x01);
8219	while (((inb(addr+1) & 0x40) == 0x40) && (timeout)) {
8220	timeout--;
8221	}
8222	}
8223	if (regs.u.r8.ah == 1) {
8224	val8 = inb(addr+2);
8225	outb(addr+2, val8 & ~0x04); // send init
8226	ASM_START
8227	nop
8228	ASM_END
8229	outb(addr+2, val8 \| 0x04);
8230	}
8231	val8 = inb(addr+1);
8232	regs.u.r8.ah = (val8 ^ 0x48);
8233	if (!timeout) regs.u.r8.ah \|= 0x01;
8234	ClearCF(iret_addr.flags);
8235	} else {
8236	SetCF(iret_addr.flags); // Unsupported
8237	}
8238	}
8239
8240	// returns bootsegment in ax, drive in bl
8241	Bit32u
8242	int19_function(bseqnr)
8243	Bit8u bseqnr;
8244	{
8245	Bit16u ebda_seg=read_word(0x0040,0x000E);
8246	Bit16u bootseq;
8247	Bit8u bootdrv;
8248	Bit8u bootcd;
8249	#ifdef VBOX
8250	Bit8u bootlan;
8251	#endif /* VBOX */
8252	Bit8u bootchk;
8253	Bit16u bootseg;
8254	Bit16u status;
8255	Bit8u lastdrive=0;
8256
8257	// if BX_ELTORITO_BOOT is not defined, old behavior
8258	// check bit 5 in CMOS reg 0x2d. load either 0x00 or 0x80 into DL
8259	// in preparation for the intial INT 13h (0=floppy A:, 0x80=C:)
8260	// 0: system boot sequence, first drive C: then A:
8261	// 1: system boot sequence, first drive A: then C:
8262	// else BX_ELTORITO_BOOT is defined
8263	// CMOS regs 0x3D and 0x38 contain the boot sequence:
8264	// CMOS reg 0x3D & 0x0f : 1st boot device
8265	// CMOS reg 0x3D & 0xf0 : 2nd boot device
8266	// CMOS reg 0x38 & 0xf0 : 3rd boot device
8267	#ifdef VBOX
8268	// CMOS reg 0x3C & 0x0f : 4th boot device
8269	#endif /* VBOX */
8270	// boot device codes:
8271	// 0x00 : not defined
8272	// 0x01 : first floppy
8273	// 0x02 : first harddrive
8274	// 0x03 : first cdrom
8275	#ifdef VBOX
8276	// 0x04 : local area network
8277	#endif /* VBOX */
8278	// else : boot failure
8279
8280	// Get the boot sequence
8281	#if BX_ELTORITO_BOOT
8282	bootseq=inb_cmos(0x3d);
8283	bootseq\|=((inb_cmos(0x38) & 0xf0) << 4);
8284	#ifdef VBOX
8285	bootseq\|=((inb_cmos(0x3c) & 0x0f) << 12);
8286	if (read_byte(ebda_seg, &EbdaData->uForceBootDevice))
8287	bootseq = read_byte(ebda_seg, &EbdaData->uForceBootDevice);
8288	/* Boot delay hack. */
8289	if (bseqnr == 1)
8290	delay_boot((inb_cmos(0x3c) & 0xf0) >> 4); /* Implemented in logo.c */
8291	#endif /* VBOX */
8292
8293	if (bseqnr==2) bootseq >>= 4;
8294	if (bseqnr==3) bootseq >>= 8;
8295	#ifdef VBOX
8296	if (bseqnr==4) bootseq >>= 12;
8297	#endif /* VBOX */
8298	if (bootseq<0x10) lastdrive = 1;
8299	bootdrv=0x00; bootcd=0;
8300	#ifdef VBOX
8301	bootlan=0;
8302	#endif /* VBOX */
8303
8304	switch(bootseq & 0x0f) {
8305	case 0x01:
8306	bootdrv=0x00;
8307	bootcd=0;
8308	break;
8309	case 0x02:
8310	{
8311	// Get the Boot drive.
8312	Bit8u boot_drive = read_byte(ebda_seg, &EbdaData->uForceBootDrive);
8313
8314	bootdrv = boot_drive + 0x80;
8315	bootcd=0;
8316	break;
8317	}
8318	case 0x03:
8319	bootdrv=0x00;
8320	bootcd=1;
8321	break;
8322	#ifdef VBOX
8323	case 0x04: bootlan=1; break;
8324	#endif /* VBOX */
8325	default: return 0x00000000;
8326	}
8327	#else
8328	bootseq=inb_cmos(0x2d);
8329
8330	if (bseqnr==2) {
8331	bootseq ^= 0x20;
8332	lastdrive = 1;
8333	}
8334	bootdrv=0x00; bootcd=0;
8335	if((bootseq&0x20)==0) bootdrv=0x80;
8336	#endif // BX_ELTORITO_BOOT
8337
8338	#if BX_ELTORITO_BOOT
8339	// We have to boot from cd
8340	if (bootcd != 0) {
8341	status = cdrom_boot();
8342
8343	// If failure
8344	if ( (status & 0x00ff) !=0 ) {
8345	print_cdromboot_failure(status);
8346	#ifdef VBOX
8347	print_boot_failure(bootcd, bootlan, bootdrv, 1, lastdrive);
8348	#else /* !VBOX */
8349	print_boot_failure(bootcd, bootdrv, 1, lastdrive);
8350	#endif /* !VBOX */
8351	return 0x00000000;
8352	}
8353
8354	bootseg = read_word(ebda_seg,&EbdaData->cdemu.load_segment);
8355	bootdrv = (Bit8u)(status>>8);
8356	}
8357
8358	#endif // BX_ELTORITO_BOOT
8359
8360	#ifdef VBOX
8361	// Check for boot from LAN first
8362	if (bootlan == 1) {
8363	if (read_word(VBOX_LANBOOT_SEG,0) == 0xaa55) {
8364	Bit16u pnpoff;
8365	Bit32u manuf;
8366	// This is NOT a generic PnP implementation, but an Etherboot-specific hack.
8367	pnpoff = read_word(VBOX_LANBOOT_SEG,0x1a);
8368	if (read_dword(VBOX_LANBOOT_SEG,pnpoff) == 0x506e5024) {
8369	// Found PnP signature
8370	manuf = read_dword(VBOX_LANBOOT_SEG,read_word(VBOX_LANBOOT_SEG,pnpoff+0xe));
8371	if (manuf == 0x65687445) {
8372	// Found Etherboot ROM
8373	print_boot_device(bootcd, bootlan, bootdrv);
8374	ASM_START
8375	push ds
8376	push es
8377	pusha
8378	calli 0x0006,VBOX_LANBOOT_SEG
8379	popa
8380	pop es
8381	pop ds
8382	ASM_END
8383	} else if (manuf == 0x65746E49) {
8384	// Found Intel PXE ROM
8385	print_boot_device(bootcd, bootlan, bootdrv);
8386	ASM_START
8387	push ds
8388	push es
8389	pusha
8390	sti ; Why are interrupts disabled now? Because we were called through an INT!
8391	push #VBOX_LANBOOT_SEG
8392	pop ds
8393	mov bx,#0x1a ; PnP header offset
8394	mov bx,[bx]
8395	add bx,#0x1a ; BEV offset in PnP header
8396	mov ax,[bx]
8397	test ax,ax
8398	jz no_rom
8399	bev_jump:
8400	push cs
8401	push #no_rom
8402	push #VBOX_LANBOOT_SEG
8403	push ax
8404	retf ; call Boot Entry Vector
8405	no_rom:
8406	popa
8407	pop es
8408	pop ds
8409	ASM_END
8410	}
8411	}
8412	}
8413
8414	// boot from LAN will not return if successful.
8415	print_boot_failure(bootcd, bootlan, bootdrv, 1, lastdrive);
8416	return 0x00000000;
8417	}
8418	#endif /* VBOX */
8419	// We have to boot from harddisk or floppy
8420	#ifdef VBOX
8421	if (bootcd == 0 && bootlan == 0) {
8422	#else /* !VBOX */
8423	if (bootcd == 0) {
8424	#endif /* !VBOX */
8425	bootseg=0x07c0;
8426
8427	ASM_START
8428	push bp
8429	mov bp, sp
8430
8431	xor ax, ax
8432	mov _int19_function.status + 2[bp], ax
8433	mov dl, _int19_function.bootdrv + 2[bp]
8434	mov ax, _int19_function.bootseg + 2[bp]
8435	mov es, ax ;; segment
8436	xor bx, bx ;; offset
8437	mov ah, #0x02 ;; function 2, read diskette sector
8438	mov al, #0x01 ;; read 1 sector
8439	mov ch, #0x00 ;; track 0
8440	mov cl, #0x01 ;; sector 1
8441	mov dh, #0x00 ;; head 0
8442	int #0x13 ;; read sector
8443	jnc int19_load_done
8444	mov ax, #0x0001
8445	mov _int19_function.status + 2[bp], ax
8446
8447	int19_load_done:
8448	pop bp
8449	ASM_END
8450
8451	if (status != 0) {
8452	#ifdef VBOX
8453	print_boot_failure(bootcd, bootlan, bootdrv, 1, lastdrive);
8454	#else /* !VBOX */
8455	print_boot_failure(bootcd, bootdrv, 1, lastdrive);
8456	#endif /* !VBOX */
8457	return 0x00000000;
8458	}
8459	}
8460
8461	#ifdef VBOX
8462	// Don't check boot sectors on floppies and don't read CMOS - byte
8463	// 0x38 in CMOS always has the low bit clear.
8464	// There is no requirement whatsoever for a valid boot sector to
8465	// have a 55AAh signature. UNIX boot floppies typically have no such
8466	// signature. In general, it is impossible to tell a valid bootsector
8467	// from an invalid one.
8468	// NB: It is somewhat common for failed OS installs to have the
8469	// 0x55AA signature and a valid partition table but zeros in the
8470	// rest of the boot sector. We do a quick check by comparing the first
8471	// two words of boot sector; if identical, the boot sector is
8472	// extremely unlikely to be valid.
8473	#endif
8474	// check signature if instructed by cmos reg 0x38, only for floppy
8475	// bootchk = 1 : signature check disabled
8476	// bootchk = 0 : signature check enabled
8477	if (bootdrv != 0) bootchk = 0;
8478	#ifdef VBOX
8479	else bootchk = 1; /* disable 0x55AA signature check on drive A: */
8480	#else
8481	else bootchk = inb_cmos(0x38) & 0x01;
8482	#endif
8483
8484	#if BX_ELTORITO_BOOT
8485	// if boot from cd, no signature check
8486	if (bootcd != 0)
8487	bootchk = 1;
8488	#endif // BX_ELTORITO_BOOT
8489
8490	if (bootchk == 0) {
8491	if (read_word(bootseg,0x1fe) != 0xaa55 \|\|
8492	read_word(bootseg,0) == read_word(bootseg,2)) {
8493	#ifdef VBOX
8494	print_boot_failure(bootcd, bootlan, bootdrv, 0, lastdrive);
8495	#else /* !VBOX */
8496	print_boot_failure(bootcd, bootdrv, 0, lastdrive);
8497	#endif /* VBOX */
8498	return 0x00000000;
8499	}
8500	}
8501
8502	#if BX_ELTORITO_BOOT
8503	// Print out the boot string
8504	#ifdef VBOX
8505	print_boot_device(bootcd, bootlan, bootdrv);
8506	#else /* !VBOX */
8507	print_boot_device(bootcd, bootdrv);
8508	#endif /* !VBOX */
8509	#else // BX_ELTORITO_BOOT
8510	#ifdef VBOX
8511	print_boot_device(0, bootlan, bootdrv);
8512	#else /* !VBOX */
8513	print_boot_device(0, bootdrv);
8514	#endif /* !VBOX */
8515	#endif // BX_ELTORITO_BOOT
8516
8517	// return the boot segment
8518	return (((Bit32u)bootdrv) << 16) + bootseg;
8519	}
8520
8521	void
8522	int1a_function(regs, ds, iret_addr)
8523	pusha_regs_t regs; // regs pushed from PUSHA instruction
8524	Bit16u ds; // previous DS:, DS set to 0x0000 by asm wrapper
8525	iret_addr_t iret_addr; // CS,IP,Flags pushed from original INT call
8526	{
8527	Bit8u val8;
8528
8529	BX_DEBUG_INT1A("int1a: AX=%04x BX=%04x CX=%04x DX=%04x DS=%04x\n", regs.u.r16.ax, regs.u.r16.bx, regs.u.r16.cx, regs.u.r16.dx, ds);
8530
8531	ASM_START
8532	sti
8533	ASM_END
8534
8535	switch (regs.u.r8.ah) {
8536	case 0: // get current clock count
8537	ASM_START
8538	cli
8539	ASM_END
8540	regs.u.r16.cx = BiosData->ticks_high;
8541	regs.u.r16.dx = BiosData->ticks_low;
8542	regs.u.r8.al = BiosData->midnight_flag;
8543	BiosData->midnight_flag = 0; // reset flag
8544	ASM_START
8545	sti
8546	ASM_END
8547	// AH already 0
8548	ClearCF(iret_addr.flags); // OK
8549	break;
8550
8551	case 1: // Set Current Clock Count
8552	ASM_START
8553	cli
8554	ASM_END
8555	BiosData->ticks_high = regs.u.r16.cx;
8556	BiosData->ticks_low = regs.u.r16.dx;
8557	BiosData->midnight_flag = 0; // reset flag
8558	ASM_START
8559	sti
8560	ASM_END
8561	regs.u.r8.ah = 0;
8562	ClearCF(iret_addr.flags); // OK
8563	break;
8564
8565
8566	case 2: // Read CMOS Time
8567	if (rtc_updating()) {
8568	SetCF(iret_addr.flags);
8569	break;
8570	}
8571
8572	regs.u.r8.dh = inb_cmos(0x00); // Seconds
8573	regs.u.r8.cl = inb_cmos(0x02); // Minutes
8574	regs.u.r8.ch = inb_cmos(0x04); // Hours
8575	regs.u.r8.dl = inb_cmos(0x0b) & 0x01; // Stat Reg B
8576	regs.u.r8.ah = 0;
8577	regs.u.r8.al = regs.u.r8.ch;
8578	ClearCF(iret_addr.flags); // OK
8579	break;
8580
8581	case 3: // Set CMOS Time
8582	// Using a debugger, I notice the following masking/setting
8583	// of bits in Status Register B, by setting Reg B to
8584	// a few values and getting its value after INT 1A was called.
8585	//
8586	// try#1 try#2 try#3
8587	// before 1111 1101 0111 1101 0000 0000
8588	// after 0110 0010 0110 0010 0000 0010
8589	//
8590	// Bit4 in try#1 flipped in hardware (forced low) due to bit7=1
8591	// My assumption: RegB = ((RegB & 01100000b) \| 00000010b)
8592	if (rtc_updating()) {
8593	init_rtc();
8594	// fall through as if an update were not in progress
8595	}
8596	outb_cmos(0x00, regs.u.r8.dh); // Seconds
8597	outb_cmos(0x02, regs.u.r8.cl); // Minutes
8598	outb_cmos(0x04, regs.u.r8.ch); // Hours
8599	// Set Daylight Savings time enabled bit to requested value
8600	val8 = (inb_cmos(0x0b) & 0x60) \| 0x02 \| (regs.u.r8.dl & 0x01);
8601	// (reg B already selected)
8602	outb_cmos(0x0b, val8);
8603	regs.u.r8.ah = 0;
8604	regs.u.r8.al = val8; // val last written to Reg B
8605	ClearCF(iret_addr.flags); // OK
8606	break;
8607
8608	case 4: // Read CMOS Date
8609	regs.u.r8.ah = 0;
8610	if (rtc_updating()) {
8611	SetCF(iret_addr.flags);
8612	break;
8613	}
8614	regs.u.r8.cl = inb_cmos(0x09); // Year
8615	regs.u.r8.dh = inb_cmos(0x08); // Month
8616	regs.u.r8.dl = inb_cmos(0x07); // Day of Month
8617	regs.u.r8.ch = inb_cmos(0x32); // Century
8618	regs.u.r8.al = regs.u.r8.ch;
8619	ClearCF(iret_addr.flags); // OK
8620	break;
8621
8622	case 5: // Set CMOS Date
8623	// Using a debugger, I notice the following masking/setting
8624	// of bits in Status Register B, by setting Reg B to
8625	// a few values and getting its value after INT 1A was called.
8626	//
8627	// try#1 try#2 try#3 try#4
8628	// before 1111 1101 0111 1101 0000 0010 0000 0000
8629	// after 0110 1101 0111 1101 0000 0010 0000 0000
8630	//
8631	// Bit4 in try#1 flipped in hardware (forced low) due to bit7=1
8632	// My assumption: RegB = (RegB & 01111111b)
8633	if (rtc_updating()) {
8634	init_rtc();
8635	SetCF(iret_addr.flags);
8636	break;
8637	}
8638	outb_cmos(0x09, regs.u.r8.cl); // Year
8639	outb_cmos(0x08, regs.u.r8.dh); // Month
8640	outb_cmos(0x07, regs.u.r8.dl); // Day of Month
8641	outb_cmos(0x32, regs.u.r8.ch); // Century
8642	val8 = inb_cmos(0x0b) & 0x7f; // clear halt-clock bit
8643	outb_cmos(0x0b, val8);
8644	regs.u.r8.ah = 0;
8645	regs.u.r8.al = val8; // AL = val last written to Reg B
8646	ClearCF(iret_addr.flags); // OK
8647	break;
8648
8649	case 6: // Set Alarm Time in CMOS
8650	// Using a debugger, I notice the following masking/setting
8651	// of bits in Status Register B, by setting Reg B to
8652	// a few values and getting its value after INT 1A was called.
8653	//
8654	// try#1 try#2 try#3
8655	// before 1101 1111 0101 1111 0000 0000
8656	// after 0110 1111 0111 1111 0010 0000
8657	//
8658	// Bit4 in try#1 flipped in hardware (forced low) due to bit7=1
8659	// My assumption: RegB = ((RegB & 01111111b) \| 00100000b)
8660	val8 = inb_cmos(0x0b); // Get Status Reg B
8661	regs.u.r16.ax = 0;
8662	if (val8 & 0x20) {
8663	// Alarm interrupt enabled already
8664	SetCF(iret_addr.flags); // Error: alarm in use
8665	break;
8666	}
8667	if (rtc_updating()) {
8668	init_rtc();
8669	// fall through as if an update were not in progress
8670	}
8671	outb_cmos(0x01, regs.u.r8.dh); // Seconds alarm
8672	outb_cmos(0x03, regs.u.r8.cl); // Minutes alarm
8673	outb_cmos(0x05, regs.u.r8.ch); // Hours alarm
8674	outb(0xa1, inb(0xa1) & 0xfe); // enable IRQ 8
8675	// enable Status Reg B alarm bit, clear halt clock bit
8676	outb_cmos(0x0b, (val8 & 0x7f) \| 0x20);
8677	ClearCF(iret_addr.flags); // OK
8678	break;
8679
8680	case 7: // Turn off Alarm
8681	// Using a debugger, I notice the following masking/setting
8682	// of bits in Status Register B, by setting Reg B to
8683	// a few values and getting its value after INT 1A was called.
8684	//
8685	// try#1 try#2 try#3 try#4
8686	// before 1111 1101 0111 1101 0010 0000 0010 0010
8687	// after 0100 0101 0101 0101 0000 0000 0000 0010
8688	//
8689	// Bit4 in try#1 flipped in hardware (forced low) due to bit7=1
8690	// My assumption: RegB = (RegB & 01010111b)
8691	val8 = inb_cmos(0x0b); // Get Status Reg B
8692	// clear clock-halt bit, disable alarm bit
8693	outb_cmos(0x0b, val8 & 0x57); // disable alarm bit
8694	regs.u.r8.ah = 0;
8695	regs.u.r8.al = val8; // val last written to Reg B
8696	ClearCF(iret_addr.flags); // OK
8697	break;
8698	#if BX_PCIBIOS
8699	case 0xb1:
8700	// real mode PCI BIOS functions now handled in assembler code
8701	// this C code handles the error code for information only
8702	if (regs.u.r8.bl == 0xff) {
8703	BX_INFO("PCI BIOS: PCI not present\n");
8704	} else if (regs.u.r8.bl == 0x81) {
8705	BX_INFO("unsupported PCI BIOS function 0x%02x\n", regs.u.r8.al);
8706	} else if (regs.u.r8.bl == 0x83) {
8707	BX_INFO("bad PCI vendor ID %04x\n", regs.u.r16.dx);
8708	} else if (regs.u.r8.bl == 0x86) {
8709	if (regs.u.r8.al == 0x02) {
8710	BX_INFO("PCI device %04x:%04x not found at index %d\n", regs.u.r16.dx, regs.u.r16.cx, regs.u.r16.si);
8711	} else {
8712	BX_INFO("no PCI device with class code 0x%02x%04x found at index %d\n", regs.u.r8.cl, regs.u.r16.dx, regs.u.r16.si);
8713	}
8714	}
8715	regs.u.r8.ah = regs.u.r8.bl;
8716	SetCF(iret_addr.flags);
8717	break;
8718	#endif
8719
8720	default:
8721	SetCF(iret_addr.flags); // Unsupported
8722	}
8723	}
8724
8725	void
8726	int70_function(regs, ds, iret_addr)
8727	pusha_regs_t regs; // regs pushed from PUSHA instruction
8728	Bit16u ds; // previous DS:, DS set to 0x0000 by asm wrapper
8729	iret_addr_t iret_addr; // CS,IP,Flags pushed from original INT call
8730	{
8731	// INT 70h: IRQ 8 - CMOS RTC interrupt from periodic or alarm modes
8732	Bit8u registerB = 0, registerC = 0;
8733
8734	// Check which modes are enabled and have occurred.
8735	registerB = inb_cmos( 0xB );
8736	registerC = inb_cmos( 0xC );
8737
8738	if( ( registerB & 0x60 ) != 0 ) {
8739	if( ( registerC & 0x20 ) != 0 ) {
8740	// Handle Alarm Interrupt.
8741	ASM_START
8742	sti
8743	int #0x4a
8744	cli
8745	ASM_END
8746	}
8747	if( ( registerC & 0x40 ) != 0 ) {
8748	// Handle Periodic Interrupt.
8749
8750	if( read_byte( 0x40, 0xA0 ) != 0 ) {
8751	// Wait Interval (Int 15, AH=83) active.
8752	Bit32u time, toggle;
8753
8754	time = read_dword( 0x40, 0x9C ); // Time left in microseconds.
8755	if( time < 0x3D1 ) {
8756	// Done waiting.
8757	Bit16u segment, offset;
8758
8759	segment = read_word( 0x40, 0x98 );
8760	offset = read_word( 0x40, 0x9A );
8761	write_byte( 0x40, 0xA0, 0 ); // Turn of status byte.
8762	outb_cmos( 0xB, registerB & 0x37 ); // Clear the Periodic Interrupt.
8763	write_byte(segment, offset, read_byte(segment, offset) \| 0x80 ); // Write to specified flag byte.
8764	} else {
8765	// Continue waiting.
8766	time -= 0x3D1;
8767	write_dword( 0x40, 0x9C, time );
8768	}
8769	}
8770	}
8771	}
8772
8773	ASM_START
8774	call eoi_both_pics
8775	ASM_END
8776	}
8777
8778	void
8779	dummy_isr_function(regs, ds, iret_addr)
8780	pusha_regs_t regs; // regs pushed from PUSHA instruction
8781	Bit16u ds; // previous DS:, DS set to 0x0000 by asm wrapper
8782	iret_addr_t iret_addr; // CS,IP,Flags pushed from original INT call
8783	{
8784	// Interrupt handler for unexpected hardware interrupts. We have to clear
8785	// the PIC because if we don't, the next EOI will clear the wrong interrupt
8786	// and all hell will break loose! This routine also masks the unexpected
8787	// interrupt so it will generally be called only once for each unexpected
8788	// interrupt level.
8789	Bit8u isrA, isrB, imr, last_int = 0xFF;
8790
8791	outb( 0x20, 0x0B );
8792	isrA = inb( 0x20 );
8793	if (isrA) {
8794	outb( 0xA0, 0x0B );
8795	isrB = inb( 0xA0 );
8796	if (isrB) {
8797	imr = inb( 0xA1 );
8798	outb( 0xA1, imr \| isrB ); // Mask this interrupt
8799	outb( 0xA0, 0x20 ); // Send EOI on slave PIC
8800	} else {
8801	imr = inb( 0x21 );
8802	isrA &= 0xFB; // Never mask the cascade interrupt
8803	outb( 0x21, imr \| isrA); // Mask this interrupt
8804	}
8805	outb( 0x20, 0x20 ); // Send EOI on master PIC
8806	last_int = isrA;
8807	}
8808	write_byte( 0x40, 0x6B, last_int ); // Write INTR_FLAG
8809	}
8810
8811	ASM_START
8812	;------------------------------------------
8813	;- INT74h : PS/2 mouse hardware interrupt -
8814	;------------------------------------------
8815	int74_handler:
8816	sti
8817	pusha
8818	push ds ;; save DS
8819	push #0x00 ;; placeholder for status
8820	push #0x00 ;; placeholder for X
8821	push #0x00 ;; placeholder for Y
8822	push #0x00 ;; placeholder for Z
8823	push #0x00 ;; placeholder for make_far_call boolean
8824	call _int74_function
8825	pop cx ;; remove make_far_call from stack
8826	jcxz int74_done
8827
8828	;; make far call to EBDA:0022
8829	push #0x00
8830	pop ds
8831	push 0x040E ;; push 0000:040E (opcodes 0xff, 0x36, 0x0E, 0x04)
8832	pop ds
8833	//CALL_EP(0x0022) ;; call far routine (call_Ep DS:0022 :opcodes 0xff, 0x1e, 0x22, 0x00)
8834	call far ptr[0x22]
8835	int74_done:
8836	cli
8837	call eoi_both_pics
8838	add sp, #8 ;; pop status, x, y, z
8839
8840	pop ds ;; restore DS
8841	popa
8842	iret
8843
8844
8845	;; This will perform an IRET, but will retain value of current CF
8846	;; by altering flags on stack. Better than RETF #02.
8847	iret_modify_cf:
8848	jc carry_set
8849	push bp
8850	mov bp, sp
8851	and BYTE [bp + 0x06], #0xfe
8852	pop bp
8853	iret
8854	carry_set:
8855	push bp
8856	mov bp, sp
8857	or BYTE [bp + 0x06], #0x01
8858	pop bp
8859	iret
8860
8861
8862	;----------------------
8863	;- INT13h (relocated) -
8864	;----------------------
8865	;
8866	; int13_relocated is a little bit messed up since I played with it
8867	; I have to rewrite it:
8868	; - call a function that detect which function to call
8869	; - make all called C function get the same parameters list
8870	;
8871	int13_relocated:
8872
8873	#if BX_ELTORITO_BOOT
8874	;; check for an eltorito function
8875	cmp ah,#0x4a
8876	jb int13_not_eltorito
8877	cmp ah,#0x4d
8878	ja int13_not_eltorito
8879
8880	pusha
8881	push es
8882	push ds
8883	push ss
8884	pop ds
8885
8886	push #int13_out
8887	jmp _int13_eltorito ;; ELDX not used
8888
8889	int13_not_eltorito:
8890	push ax
8891	push bx
8892	push cx
8893	push dx
8894
8895	;; check if emulation active
8896	call _cdemu_isactive
8897	cmp al,#0x00
8898	je int13_cdemu_inactive
8899
8900	;; check if access to the emulated drive
8901	call _cdemu_emulated_drive
8902	pop dx
8903	push dx
8904	cmp al,dl ;; int13 on emulated drive
8905	jne int13_nocdemu
8906
8907	pop dx
8908	pop cx
8909	pop bx
8910	pop ax
8911
8912	pusha
8913	push es
8914	push ds
8915	push ss
8916	pop ds
8917
8918	push #int13_out
8919	jmp _int13_cdemu ;; ELDX not used
8920
8921	int13_nocdemu:
8922	and dl,#0xE0 ;; mask to get device class, including cdroms
8923	cmp al,dl ;; al is 0x00 or 0x80
8924	jne int13_cdemu_inactive ;; inactive for device class
8925
8926	pop dx
8927	pop cx
8928	pop bx
8929	pop ax
8930
8931	push ax
8932	push cx
8933	push dx
8934	push bx
8935
8936	dec dl ;; real drive is dl - 1
8937	jmp int13_legacy
8938
8939	int13_cdemu_inactive:
8940	pop dx
8941	pop cx
8942	pop bx
8943	pop ax
8944
8945	#endif // BX_ELTORITO_BOOT
8946
8947	int13_noeltorito:
8948
8949	push ax
8950	push cx
8951	push dx
8952	push bx
8953
8954	int13_legacy:
8955
8956	push dx ;; push eltorito value of dx instead of sp
8957
8958	push bp
8959	push si
8960	push di
8961
8962	push es
8963	push ds
8964	push ss
8965	pop ds
8966
8967	;; now the 16-bit registers can be restored with:
8968	;; pop ds; pop es; popa; iret
8969	;; arguments passed to functions should be
8970	;; DS, ES, DI, SI, BP, ELDX, BX, DX, CX, AX, IP, CS, FLAGS
8971
8972	test dl, #0x80
8973	jnz int13_notfloppy
8974
8975	push #int13_out
8976	jmp _int13_diskette_function
8977
8978	int13_notfloppy:
8979
8980	#if BX_USE_ATADRV
8981
8982	cmp dl, #0xE0
8983	jb int13_notcdrom
8984
8985	// ebx is modified: BSD 5.2.1 boot loader problem
8986	// someone should figure out which 32 bit register that actually are used
8987
8988	shr ebx, #16
8989	push bx
8990
8991	call _int13_cdrom
8992
8993	pop bx
8994	shl ebx, #16
8995
8996	jmp int13_out
8997
8998	int13_notcdrom:
8999
9000	#endif
9001
9002	int13_disk:
9003	;; int13_harddisk modifies high word of EAX
9004	shr eax, #16
9005	push ax
9006	call _int13_harddisk
9007	pop ax
9008	shl eax, #16
9009
9010	int13_out:
9011	pop ds
9012	pop es
9013	popa
9014	iret
9015
9016
9017	;----------
9018	;- INT18h -
9019	;----------
9020	int18_handler: ;; Boot Failure routing
9021	call _int18_panic_msg
9022	hlt
9023	iret
9024
9025	;----------
9026	;- INT19h -
9027	;----------
9028	int19_relocated: ;; Boot function, relocated
9029
9030	#ifdef VBOX
9031	// If an already booted OS calls int 0x19 to reboot, it is not sufficient
9032	// just to try booting from the configured drives. All BIOS variables and
9033	// interrupt vectors need to be reset, otherwise strange things may happen.
9034	// The approach used is faking a warm reboot (which just skips showing the
9035	// logo), which is a bit more than what we need, but hey, it's fast.
9036	mov bp, sp
9037	mov ax, 2[bp]
9038	cmp ax, #0xf000
9039	jz bios_initiated_boot
9040	xor ax, ax
9041	mov ds, ax
9042	mov ax, #0x1234
9043	mov 0x472, ax
9044	jmp post
9045	bios_initiated_boot:
9046	#endif /* VBOX */
9047
9048	;; int19 was beginning to be really complex, so now it
9049	;; just calls an C function, that does the work
9050	;; it returns in BL the boot drive, and in AX the boot segment
9051	;; the boot segment will be 0x0000 if something has failed
9052
9053	push bp
9054	mov bp, sp
9055
9056	;; drop ds
9057	xor ax, ax
9058	mov ds, ax
9059
9060	;; 1st boot device
9061	mov ax, #0x0001
9062	push ax
9063	call _int19_function
9064	inc sp
9065	inc sp
9066	;; bl contains the boot drive
9067	;; ax contains the boot segment or 0 if failure
9068
9069	test ax, ax ;; if ax is 0 try next boot device
9070	jnz boot_setup
9071
9072	;; 2nd boot device
9073	mov ax, #0x0002
9074	push ax
9075	call _int19_function
9076	inc sp
9077	inc sp
9078	test ax, ax ;; if ax is 0 try next boot device
9079	jnz boot_setup
9080
9081	;; 3rd boot device
9082	mov ax, #0x0003
9083	push ax
9084	call _int19_function
9085	inc sp
9086	inc sp
9087	#ifdef VBOX
9088	test ax, ax ;; if ax is 0 try next boot device
9089	jnz boot_setup
9090
9091	;; 4th boot device
9092	mov ax, #0x0004
9093	push ax
9094	call _int19_function
9095	inc sp
9096	inc sp
9097	#endif /* VBOX */
9098	test ax, ax ;; if ax is 0 call int18
9099	jz int18_handler
9100
9101	boot_setup:
9102	mov dl, bl ;; set drive so guest os find it
9103	shl eax, #0x04 ;; convert seg to ip
9104	mov 2[bp], ax ;; set ip
9105
9106	shr eax, #0x04 ;; get cs back
9107	and ax, #0xF000 ;; remove what went in ip
9108	mov 4[bp], ax ;; set cs
9109	xor ax, ax
9110	mov es, ax ;; set es to zero fixes [ 549815 ]
9111	mov [bp], ax ;; set bp to zero
9112	mov ax, #0xaa55 ;; set ok flag
9113
9114	pop bp
9115	iret ;; Beam me up Scotty
9116
9117	;----------
9118	;- INT1Ch -
9119	;----------
9120	int1c_handler: ;; User Timer Tick
9121	iret
9122
9123
9124	;----------------------
9125	;- POST: Floppy Drive -
9126	;----------------------
9127	floppy_drive_post:
9128	xor ax, ax
9129	mov ds, ax
9130
9131	mov al, #0x00
9132	mov 0x043e, al ;; drive 0 & 1 uncalibrated, no interrupt has occurred
9133
9134	mov 0x043f, al ;; diskette motor status: read op, drive0, motors off
9135
9136	mov 0x0440, al ;; diskette motor timeout counter: not active
9137	mov 0x0441, al ;; diskette controller status return code
9138
9139	mov 0x0442, al ;; disk & diskette controller status register 0
9140	mov 0x0443, al ;; diskette controller status register 1
9141	mov 0x0444, al ;; diskette controller status register 2
9142	mov 0x0445, al ;; diskette controller cylinder number
9143	mov 0x0446, al ;; diskette controller head number
9144	mov 0x0447, al ;; diskette controller sector number
9145	mov 0x0448, al ;; diskette controller bytes written
9146
9147	mov 0x048b, al ;; diskette configuration data
9148
9149	;; -----------------------------------------------------------------
9150	;; (048F) diskette controller information
9151	;;
9152	mov al, #0x10 ;; get CMOS diskette drive type
9153	out 0x70, AL
9154	in AL, 0x71
9155	mov ah, al ;; save byte to AH
9156
9157	look_drive0:
9158	shr al, #4 ;; look at top 4 bits for drive 0
9159	jz f0_missing ;; jump if no drive0
9160	mov bl, #0x07 ;; drive0 determined, multi-rate, has changed line
9161	jmp look_drive1
9162	f0_missing:
9163	mov bl, #0x00 ;; no drive0
9164
9165	look_drive1:
9166	mov al, ah ;; restore from AH
9167	and al, #0x0f ;; look at bottom 4 bits for drive 1
9168	jz f1_missing ;; jump if no drive1
9169	or bl, #0x70 ;; drive1 determined, multi-rate, has changed line
9170	f1_missing:
9171	;; leave high bits in BL zerod
9172	mov 0x048f, bl ;; put new val in BDA (diskette controller information)
9173	;; -----------------------------------------------------------------
9174
9175	mov al, #0x00
9176	mov 0x0490, al ;; diskette 0 media state
9177	mov 0x0491, al ;; diskette 1 media state
9178
9179	;; diskette 0,1 operational starting state
9180	;; drive type has not been determined,
9181	;; has no changed detection line
9182	mov 0x0492, al
9183	mov 0x0493, al
9184
9185	mov 0x0494, al ;; diskette 0 current cylinder
9186	mov 0x0495, al ;; diskette 1 current cylinder
9187
9188	mov al, #0x02
9189	out #0x0a, al ;; clear DMA-1 channel 2 mask bit
9190
9191	SET_INT_VECTOR(0x1E, #0xF000, #diskette_param_table2)
9192	SET_INT_VECTOR(0x40, #0xF000, #int13_diskette)
9193	SET_INT_VECTOR(0x0E, #0xF000, #int0e_handler) ;; IRQ 6
9194
9195	ret
9196
9197
9198	;--------------------
9199	;- POST: HARD DRIVE -
9200	;--------------------
9201	; relocated here because the primary POST area isnt big enough.
9202	hard_drive_post:
9203	// IRQ 14 = INT 76h
9204	// INT 76h calls INT 15h function ax=9100
9205
9206	mov al, #0x0a ; 0000 1010 = reserved, disable IRQ 14
9207	mov dx, #0x03f6
9208	out dx, al
9209
9210	xor ax, ax
9211	mov ds, ax
9212	mov 0x0474, al /* hard disk status of last operation */
9213	mov 0x0477, al /* hard disk port offset (XT only ???) */
9214	mov 0x048c, al /* hard disk status register */
9215	mov 0x048d, al /* hard disk error register */
9216	mov 0x048e, al /* hard disk task complete flag */
9217	mov al, #0x01
9218	mov 0x0475, al /* hard disk number attached */
9219	mov al, #0xc0
9220	mov 0x0476, al /* hard disk control byte */
9221	SET_INT_VECTOR(0x13, #0xF000, #int13_handler)
9222	SET_INT_VECTOR(0x76, #0xF000, #int76_handler)
9223	;; INT 41h: hard disk 0 configuration pointer
9224	;; INT 46h: hard disk 1 configuration pointer
9225	SET_INT_VECTOR(0x41, #EBDA_SEG, #0x003D)
9226	SET_INT_VECTOR(0x46, #EBDA_SEG, #0x004D)
9227
9228	#ifndef VBOX /* This is done later (and the CMOS format is now different). */
9229	;; move disk geometry data from CMOS to EBDA disk parameter table(s)
9230	mov al, #0x12
9231	out #0x70, al
9232	in al, #0x71
9233	and al, #0xf0
9234	cmp al, #0xf0
9235	je post_d0_extended
9236	jmp check_for_hd1
9237	post_d0_extended:
9238	mov al, #0x19
9239	out #0x70, al
9240	in al, #0x71
9241	cmp al, #47 ;; decimal 47 - user definable
9242	je post_d0_type47
9243	HALT(__LINE__)
9244	post_d0_type47:
9245	;; CMOS purpose param table offset
9246	;; 1b cylinders low 0
9247	;; 1c cylinders high 1
9248	;; 1d heads 2
9249	;; 1e write pre-comp low 5
9250	;; 1f write pre-comp high 6
9251	;; 20 retries/bad map/heads>8 8
9252	;; 21 landing zone low C
9253	;; 22 landing zone high D
9254	;; 23 sectors/track E
9255
9256	mov ax, #EBDA_SEG
9257	mov ds, ax
9258
9259	;;; Filling EBDA table for hard disk 0.
9260	mov al, #0x1f
9261	out #0x70, al
9262	in al, #0x71
9263	mov ah, al
9264	mov al, #0x1e
9265	out #0x70, al
9266	in al, #0x71
9267	mov (0x003d + 0x05), ax ;; write precomp word
9268
9269	mov al, #0x20
9270	out #0x70, al
9271	in al, #0x71
9272	mov (0x003d + 0x08), al ;; drive control byte
9273
9274	mov al, #0x22
9275	out #0x70, al
9276	in al, #0x71
9277	mov ah, al
9278	mov al, #0x21
9279	out #0x70, al
9280	in al, #0x71
9281	mov (0x003d + 0x0C), ax ;; landing zone word
9282
9283	mov al, #0x1c ;; get cylinders word in AX
9284	out #0x70, al
9285	in al, #0x71 ;; high byte
9286	mov ah, al
9287	mov al, #0x1b
9288	out #0x70, al
9289	in al, #0x71 ;; low byte
9290	mov bx, ax ;; BX = cylinders
9291
9292	mov al, #0x1d
9293	out #0x70, al
9294	in al, #0x71
9295	mov cl, al ;; CL = heads
9296
9297	mov al, #0x23
9298	out #0x70, al
9299	in al, #0x71
9300	mov dl, al ;; DL = sectors
9301
9302	cmp bx, #1024
9303	jnbe hd0_post_logical_chs ;; if cylinders > 1024, use translated style CHS
9304
9305	hd0_post_physical_chs:
9306	;; no logical CHS mapping used, just physical CHS
9307	;; use Standard Fixed Disk Parameter Table (FDPT)
9308	mov (0x003d + 0x00), bx ;; number of physical cylinders
9309	mov (0x003d + 0x02), cl ;; number of physical heads
9310	mov (0x003d + 0x0E), dl ;; number of physical sectors
9311	jmp check_for_hd1
9312
9313	hd0_post_logical_chs:
9314	;; complies with Phoenix style Translated Fixed Disk Parameter Table (FDPT)
9315	mov (0x003d + 0x09), bx ;; number of physical cylinders
9316	mov (0x003d + 0x0b), cl ;; number of physical heads
9317	mov (0x003d + 0x04), dl ;; number of physical sectors
9318	mov (0x003d + 0x0e), dl ;; number of logical sectors (same)
9319	mov al, #0xa0
9320	mov (0x003d + 0x03), al ;; A0h signature, indicates translated table
9321
9322	cmp bx, #2048
9323	jnbe hd0_post_above_2048
9324	;; 1024 < c <= 2048 cylinders
9325	shr bx, #0x01
9326	shl cl, #0x01
9327	jmp hd0_post_store_logical
9328
9329	hd0_post_above_2048:
9330	cmp bx, #4096
9331	jnbe hd0_post_above_4096
9332	;; 2048 < c <= 4096 cylinders
9333	shr bx, #0x02
9334	shl cl, #0x02
9335	jmp hd0_post_store_logical
9336
9337	hd0_post_above_4096:
9338	cmp bx, #8192
9339	jnbe hd0_post_above_8192
9340	;; 4096 < c <= 8192 cylinders
9341	shr bx, #0x03
9342	shl cl, #0x03
9343	jmp hd0_post_store_logical
9344
9345	hd0_post_above_8192:
9346	;; 8192 < c <= 16384 cylinders
9347	shr bx, #0x04
9348	shl cl, #0x04
9349
9350	hd0_post_store_logical:
9351	mov (0x003d + 0x00), bx ;; number of physical cylinders
9352	mov (0x003d + 0x02), cl ;; number of physical heads
9353	;; checksum
9354	mov cl, #0x0f ;; repeat count
9355	mov si, #0x003d ;; offset to disk0 FDPT
9356	mov al, #0x00 ;; sum
9357	hd0_post_checksum_loop:
9358	add al, [si]
9359	inc si
9360	dec cl
9361	jnz hd0_post_checksum_loop
9362	not al ;; now take 2s complement
9363	inc al
9364	mov [si], al
9365	;;; Done filling EBDA table for hard disk 0.
9366
9367
9368	check_for_hd1:
9369	;; is there really a second hard disk? if not, return now
9370	mov al, #0x12
9371	out #0x70, al
9372	in al, #0x71
9373	and al, #0x0f
9374	jnz post_d1_exists
9375	ret
9376	post_d1_exists:
9377	;; check that the hd type is really 0x0f.
9378	cmp al, #0x0f
9379	jz post_d1_extended
9380	HALT(__LINE__)
9381	post_d1_extended:
9382	;; check that the extended type is 47 - user definable
9383	mov al, #0x1a
9384	out #0x70, al
9385	in al, #0x71
9386	cmp al, #47 ;; decimal 47 - user definable
9387	je post_d1_type47
9388	HALT(__LINE__)
9389	post_d1_type47:
9390	;; Table for disk1.
9391	;; CMOS purpose param table offset
9392	;; 0x24 cylinders low 0
9393	;; 0x25 cylinders high 1
9394	;; 0x26 heads 2
9395	;; 0x27 write pre-comp low 5
9396	;; 0x28 write pre-comp high 6
9397	;; 0x29 heads>8 8
9398	;; 0x2a landing zone low C
9399	;; 0x2b landing zone high D
9400	;; 0x2c sectors/track E
9401	;;; Fill EBDA table for hard disk 1.
9402	mov ax, #EBDA_SEG
9403	mov ds, ax
9404	mov al, #0x28
9405	out #0x70, al
9406	in al, #0x71
9407	mov ah, al
9408	mov al, #0x27
9409	out #0x70, al
9410	in al, #0x71
9411	mov (0x004d + 0x05), ax ;; write precomp word
9412
9413	mov al, #0x29
9414	out #0x70, al
9415	in al, #0x71
9416	mov (0x004d + 0x08), al ;; drive control byte
9417
9418	mov al, #0x2b
9419	out #0x70, al
9420	in al, #0x71
9421	mov ah, al
9422	mov al, #0x2a
9423	out #0x70, al
9424	in al, #0x71
9425	mov (0x004d + 0x0C), ax ;; landing zone word
9426
9427	mov al, #0x25 ;; get cylinders word in AX
9428	out #0x70, al
9429	in al, #0x71 ;; high byte
9430	mov ah, al
9431	mov al, #0x24
9432	out #0x70, al
9433	in al, #0x71 ;; low byte
9434	mov bx, ax ;; BX = cylinders
9435
9436	mov al, #0x26
9437	out #0x70, al
9438	in al, #0x71
9439	mov cl, al ;; CL = heads
9440
9441	mov al, #0x2c
9442	out #0x70, al
9443	in al, #0x71
9444	mov dl, al ;; DL = sectors
9445
9446	cmp bx, #1024
9447	jnbe hd1_post_logical_chs ;; if cylinders > 1024, use translated style CHS
9448
9449	hd1_post_physical_chs:
9450	;; no logical CHS mapping used, just physical CHS
9451	;; use Standard Fixed Disk Parameter Table (FDPT)
9452	mov (0x004d + 0x00), bx ;; number of physical cylinders
9453	mov (0x004d + 0x02), cl ;; number of physical heads
9454	mov (0x004d + 0x0E), dl ;; number of physical sectors
9455	ret
9456
9457	hd1_post_logical_chs:
9458	;; complies with Phoenix style Translated Fixed Disk Parameter Table (FDPT)
9459	mov (0x004d + 0x09), bx ;; number of physical cylinders
9460	mov (0x004d + 0x0b), cl ;; number of physical heads
9461	mov (0x004d + 0x04), dl ;; number of physical sectors
9462	mov (0x004d + 0x0e), dl ;; number of logical sectors (same)
9463	mov al, #0xa0
9464	mov (0x004d + 0x03), al ;; A0h signature, indicates translated table
9465
9466	cmp bx, #2048
9467	jnbe hd1_post_above_2048
9468	;; 1024 < c <= 2048 cylinders
9469	shr bx, #0x01
9470	shl cl, #0x01
9471	jmp hd1_post_store_logical
9472
9473	hd1_post_above_2048:
9474	cmp bx, #4096
9475	jnbe hd1_post_above_4096
9476	;; 2048 < c <= 4096 cylinders
9477	shr bx, #0x02
9478	shl cl, #0x02
9479	jmp hd1_post_store_logical
9480
9481	hd1_post_above_4096:
9482	cmp bx, #8192
9483	jnbe hd1_post_above_8192
9484	;; 4096 < c <= 8192 cylinders
9485	shr bx, #0x03
9486	shl cl, #0x03
9487	jmp hd1_post_store_logical
9488
9489	hd1_post_above_8192:
9490	;; 8192 < c <= 16384 cylinders
9491	shr bx, #0x04
9492	shl cl, #0x04
9493
9494	hd1_post_store_logical:
9495	mov (0x004d + 0x00), bx ;; number of physical cylinders
9496	mov (0x004d + 0x02), cl ;; number of physical heads
9497	;; checksum
9498	mov cl, #0x0f ;; repeat count
9499	mov si, #0x004d ;; offset to disk0 FDPT
9500	mov al, #0x00 ;; sum
9501	hd1_post_checksum_loop:
9502	add al, [si]
9503	inc si
9504	dec cl
9505	jnz hd1_post_checksum_loop
9506	not al ;; now take 2s complement
9507	inc al
9508	mov [si], al
9509	;;; Done filling EBDA table for hard disk 1.
9510	#endif /* !VBOX */
9511
9512	ret
9513
9514	;--------------------
9515	;- POST: EBDA segment
9516	;--------------------
9517	; relocated here because the primary POST area isnt big enough.
9518	; the SET_INT_VECTORs have nothing to do with EBDA but do not
9519	; fit into the primary POST area either
9520	ebda_post:
9521	SET_INT_VECTOR(0x0D, #0xF000, #dummy_isr); IRQ 5
9522	SET_INT_VECTOR(0x0F, #0xF000, #dummy_isr); IRQ 7
9523	SET_INT_VECTOR(0x72, #0xF000, #dummy_isr); IRQ 11
9524	SET_INT_VECTOR(0x77, #0xF000, #dummy_isr); IRQ 15
9525
9526	#if BX_USE_EBDA
9527	mov ax, #EBDA_SEG
9528	mov ds, ax
9529	mov byte ptr [0x0], #EBDA_SIZE
9530	#endif
9531	xor ax, ax ; mov EBDA seg into 40E
9532	mov ds, ax
9533	mov word ptr [0x40E], #EBDA_SEG
9534	ret;;
9535
9536	;--------------------
9537	;- POST: EOI + jmp via [0x40:67)
9538	;--------------------
9539	; relocated here because the primary POST area isnt big enough.
9540	eoi_jmp_post:
9541	call eoi_both_pics
9542
9543	xor ax, ax
9544	mov ds, ax
9545
9546	jmp far ptr [0x467]
9547
9548
9549	;--------------------
9550	eoi_both_pics:
9551	mov al, #0x20
9552	out #0xA0, al ;; slave PIC EOI
9553	eoi_master_pic:
9554	mov al, #0x20
9555	out #0x20, al ;; master PIC EOI
9556	ret
9557
9558	;--------------------
9559	BcdToBin:
9560	;; in: AL in BCD format
9561	;; out: AL in binary format, AH will always be 0
9562	;; trashes BX
9563	mov bl, al
9564	and bl, #0x0f ;; bl has low digit
9565	shr al, #4 ;; al has high digit
9566	mov bh, #10
9567	mul al, bh ;; multiply high digit by 10 (result in AX)
9568	add al, bl ;; then add low digit
9569	ret
9570
9571	;--------------------
9572	timer_tick_post:
9573	;; Setup the Timer Ticks Count (0x46C:dword) and
9574	;; Timer Ticks Roller Flag (0x470:byte)
9575	;; The Timer Ticks Count needs to be set according to
9576	;; the current CMOS time, as if ticks have been occurring
9577	;; at 18.2hz since midnight up to this point. Calculating
9578	;; this is a little complicated. Here are the factors I gather
9579	;; regarding this. 14,318,180 hz was the original clock speed,
9580	;; chosen so it could be divided by either 3 to drive the 5Mhz CPU
9581	;; at the time, or 4 to drive the CGA video adapter. The div3
9582	;; source was divided again by 4 to feed a 1.193Mhz signal to
9583	;; the timer. With a maximum 16bit timer count, this is again
9584	;; divided down by 65536 to 18.2hz.
9585	;;
9586	;; 14,318,180 Hz clock
9587	;; /3 = 4,772,726 Hz fed to orginal 5Mhz CPU
9588	;; /4 = 1,193,181 Hz fed to timer
9589	;; /65536 (maximum timer count) = 18.20650736 ticks/second
9590	;; 1 second = 18.20650736 ticks
9591	;; 1 minute = 1092.390442 ticks
9592	;; 1 hour = 65543.42651 ticks
9593	;;
9594	;; Given the values in the CMOS clock, one could calculate
9595	;; the number of ticks by the following:
9596	;; ticks = (BcdToBin(seconds) * 18.206507) +
9597	;; (BcdToBin(minutes) * 1092.3904)
9598	;; (BcdToBin(hours) * 65543.427)
9599	;; To get a little more accuracy, since Im using integer
9600	;; arithmatic, I use:
9601	;; ticks = (BcdToBin(seconds) * 18206507) / 1000000 +
9602	;; (BcdToBin(minutes) * 10923904) / 10000 +
9603	;; (BcdToBin(hours) * 65543427) / 1000
9604
9605	;; assuming DS=0000
9606
9607	;; get CMOS seconds
9608	xor eax, eax ;; clear EAX
9609	mov al, #0x00
9610	out #0x70, al
9611	in al, #0x71 ;; AL has CMOS seconds in BCD
9612	call BcdToBin ;; EAX now has seconds in binary
9613	mov edx, #18206507
9614	mul eax, edx
9615	mov ebx, #1000000
9616	xor edx, edx
9617	div eax, ebx
9618	mov ecx, eax ;; ECX will accumulate total ticks
9619
9620	;; get CMOS minutes
9621	xor eax, eax ;; clear EAX
9622	mov al, #0x02
9623	out #0x70, al
9624	in al, #0x71 ;; AL has CMOS minutes in BCD
9625	call BcdToBin ;; EAX now has minutes in binary
9626	mov edx, #10923904
9627	mul eax, edx
9628	mov ebx, #10000
9629	xor edx, edx
9630	div eax, ebx
9631	add ecx, eax ;; add to total ticks
9632
9633	;; get CMOS hours
9634	xor eax, eax ;; clear EAX
9635	mov al, #0x04
9636	out #0x70, al
9637	in al, #0x71 ;; AL has CMOS hours in BCD
9638	call BcdToBin ;; EAX now has hours in binary
9639	mov edx, #65543427
9640	mul eax, edx
9641	mov ebx, #1000
9642	xor edx, edx
9643	div eax, ebx
9644	add ecx, eax ;; add to total ticks
9645
9646	mov 0x46C, ecx ;; Timer Ticks Count
9647	xor al, al
9648	mov 0x470, al ;; Timer Ticks Rollover Flag
9649	ret
9650
9651	;--------------------
9652	int76_handler:
9653	;; record completion in BIOS task complete flag
9654	push ax
9655	push ds
9656	mov ax, #0x0040
9657	mov ds, ax
9658	mov 0x008E, #0xff
9659	call eoi_both_pics
9660	pop ds
9661	pop ax
9662	iret
9663
9664	;--------------------
9665	#ifdef VBOX
9666	init_pic:
9667	;; init PIC
9668	mov al, #0x11 ; send initialisation commands
9669	out 0x20, al
9670	out 0xa0, al
9671	mov al, #0x08
9672	out 0x21, al
9673	mov al, #0x70
9674	out 0xa1, al
9675	mov al, #0x04
9676	out 0x21, al
9677	mov al, #0x02
9678	out 0xa1, al
9679	mov al, #0x01
9680	out 0x21, al
9681	out 0xa1, al
9682	mov al, #0xb8
9683	out 0x21, AL ;master pic: unmask IRQ 0, 1, 2, 6
9684	#if BX_USE_PS2_MOUSE
9685	mov al, #0x8f
9686	#else
9687	mov al, #0x9f
9688	#endif
9689	out 0xa1, AL ;slave pic: unmask IRQ 12, 13, 14
9690	ret
9691	#endif /* VBOX */
9692
9693	;--------------------
9694	#if BX_APM
9695
9696	use32 386
9697	#define APM_PROT32
9698	#include "apmbios.S"
9699
9700	use16 386
9701	#define APM_PROT16
9702	#include "apmbios.S"
9703
9704	#define APM_REAL
9705	#include "apmbios.S"
9706
9707	#endif
9708
9709	;--------------------
9710	#if BX_PCIBIOS
9711	use32 386
9712	.align 16
9713	bios32_structure:
9714	db 0x5f, 0x33, 0x32, 0x5f ;; "_32_" signature
9715	dw bios32_entry_point, 0xf ;; 32 bit physical address
9716	db 0 ;; revision level
9717	;; length in paragraphs and checksum stored in a word to prevent errors
9718	dw (~(((bios32_entry_point >> 8) + (bios32_entry_point & 0xff) + 0x32) \
9719	& 0xff) << 8) + 0x01
9720	db 0,0,0,0,0 ;; reserved
9721
9722	.align 16
9723	bios32_entry_point:
9724	pushfd
9725	cmp eax, #0x49435024 ;; "$PCI"
9726	jne unknown_service
9727	mov eax, #0x80000000
9728	mov dx, #0x0cf8
9729	out dx, eax
9730	mov dx, #0x0cfc
9731	in eax, dx
9732	#ifdef PCI_FIXED_HOST_BRIDGE
9733	cmp eax, #PCI_FIXED_HOST_BRIDGE
9734	jne unknown_service
9735	#else
9736	;; say ok if a device is present
9737	cmp eax, #0xffffffff
9738	je unknown_service
9739	#endif
9740	mov ebx, #0x000f0000
9741	mov ecx, #0
9742	mov edx, #pcibios_protected
9743	xor al, al
9744	jmp bios32_end
9745	unknown_service:
9746	mov al, #0x80
9747	bios32_end:
9748	#ifdef BX_QEMU
9749	and dword ptr[esp+8],0xfffffffc ;; reset CS.RPL for kqemu
9750	#endif
9751	popfd
9752	retf
9753
9754	.align 16
9755	pcibios_protected:
9756	pushfd
9757	cli
9758	push esi
9759	push edi
9760	cmp al, #0x01 ;; installation check
9761	jne pci_pro_f02
9762	mov bx, #0x0210
9763	mov cx, #0
9764	mov edx, #0x20494350 ;; "PCI "
9765	mov al, #0x01
9766	jmp pci_pro_ok
9767	pci_pro_f02: ;; find pci device
9768	cmp al, #0x02
9769	jne pci_pro_f03
9770	shl ecx, #16
9771	mov cx, dx
9772	xor ebx, ebx
9773	mov di, #0x00
9774	pci_pro_devloop:
9775	call pci_pro_select_reg
9776	mov dx, #0x0cfc
9777	in eax, dx
9778	cmp eax, ecx
9779	jne pci_pro_nextdev
9780	cmp si, #0
9781	je pci_pro_ok
9782	dec si
9783	pci_pro_nextdev:
9784	inc ebx
9785	cmp ebx, #0x10000
9786	jne pci_pro_devloop
9787	mov ah, #0x86
9788	jmp pci_pro_fail
9789	pci_pro_f03: ;; find class code
9790	cmp al, #0x03
9791	jne pci_pro_f08
9792	xor ebx, ebx
9793	mov di, #0x08
9794	pci_pro_devloop2:
9795	call pci_pro_select_reg
9796	mov dx, #0x0cfc
9797	in eax, dx
9798	shr eax, #8
9799	cmp eax, ecx
9800	jne pci_pro_nextdev2
9801	cmp si, #0
9802	je pci_pro_ok
9803	dec si
9804	pci_pro_nextdev2:
9805	inc ebx
9806	cmp ebx, #0x10000
9807	jne pci_pro_devloop2
9808	mov ah, #0x86
9809	jmp pci_pro_fail
9810	pci_pro_f08: ;; read configuration byte
9811	cmp al, #0x08
9812	jne pci_pro_f09
9813	call pci_pro_select_reg
9814	push edx
9815	mov dx, di
9816	and dx, #0x03
9817	add dx, #0x0cfc
9818	in al, dx
9819	pop edx
9820	mov cl, al
9821	jmp pci_pro_ok
9822	pci_pro_f09: ;; read configuration word
9823	cmp al, #0x09
9824	jne pci_pro_f0a
9825	call pci_pro_select_reg
9826	push edx
9827	mov dx, di
9828	and dx, #0x02
9829	add dx, #0x0cfc
9830	in ax, dx
9831	pop edx
9832	mov cx, ax
9833	jmp pci_pro_ok
9834	pci_pro_f0a: ;; read configuration dword
9835	cmp al, #0x0a
9836	jne pci_pro_f0b
9837	call pci_pro_select_reg
9838	push edx
9839	mov dx, #0x0cfc
9840	in eax, dx
9841	pop edx
9842	mov ecx, eax
9843	jmp pci_pro_ok
9844	pci_pro_f0b: ;; write configuration byte
9845	cmp al, #0x0b
9846	jne pci_pro_f0c
9847	call pci_pro_select_reg
9848	push edx
9849	mov dx, di
9850	and dx, #0x03
9851	add dx, #0x0cfc
9852	mov al, cl
9853	out dx, al
9854	pop edx
9855	jmp pci_pro_ok
9856	pci_pro_f0c: ;; write configuration word
9857	cmp al, #0x0c
9858	jne pci_pro_f0d
9859	call pci_pro_select_reg
9860	push edx
9861	mov dx, di
9862	and dx, #0x02
9863	add dx, #0x0cfc
9864	mov ax, cx
9865	out dx, ax
9866	pop edx
9867	jmp pci_pro_ok
9868	pci_pro_f0d: ;; write configuration dword
9869	cmp al, #0x0d
9870	jne pci_pro_unknown
9871	call pci_pro_select_reg
9872	push edx
9873	mov dx, #0x0cfc
9874	mov eax, ecx
9875	out dx, eax
9876	pop edx
9877	jmp pci_pro_ok
9878	pci_pro_unknown:
9879	mov ah, #0x81
9880	pci_pro_fail:
9881	pop edi
9882	pop esi
9883	#ifdef BX_QEMU
9884	and dword ptr[esp+8],0xfffffffc ;; reset CS.RPL for kqemu
9885	#endif
9886	popfd
9887	stc
9888	retf
9889	pci_pro_ok:
9890	xor ah, ah
9891	pop edi
9892	pop esi
9893	#ifdef BX_QEMU
9894	and dword ptr[esp+8],0xfffffffc ;; reset CS.RPL for kqemu
9895	#endif
9896	popfd
9897	clc
9898	retf
9899
9900	pci_pro_select_reg:
9901	push edx
9902	mov eax, #0x800000
9903	mov ax, bx
9904	shl eax, #8
9905	and di, #0xff
9906	or ax, di
9907	and al, #0xfc
9908	mov dx, #0x0cf8
9909	out dx, eax
9910	pop edx
9911	ret
9912
9913	use16 386
9914
9915	pcibios_real:
9916	push eax
9917	push dx
9918	mov eax, #0x80000000
9919	mov dx, #0x0cf8
9920	out dx, eax
9921	mov dx, #0x0cfc
9922	in eax, dx
9923	#ifdef PCI_FIXED_HOST_BRIDGE
9924	cmp eax, #PCI_FIXED_HOST_BRIDGE
9925	je pci_present
9926	#else
9927	;; say ok if a device is present
9928	cmp eax, #0xffffffff
9929	jne pci_present
9930	#endif
9931	pop dx
9932	pop eax
9933	mov ah, #0xff
9934	stc
9935	ret
9936	pci_present:
9937	pop dx
9938	pop eax
9939	cmp al, #0x01 ;; installation check
9940	jne pci_real_f02
9941	mov ax, #0x0001
9942	mov bx, #0x0210
9943	mov cx, #0
9944	mov edx, #0x20494350 ;; "PCI "
9945	mov edi, #0xf0000
9946	mov di, #pcibios_protected
9947	clc
9948	ret
9949	pci_real_f02: ;; find pci device
9950	push esi
9951	push edi
9952	cmp al, #0x02
9953	jne pci_real_f03
9954	shl ecx, #16
9955	mov cx, dx
9956	xor ebx, ebx
9957	mov di, #0x00
9958	pci_real_devloop:
9959	call pci_real_select_reg
9960	mov dx, #0x0cfc
9961	in eax, dx
9962	cmp eax, ecx
9963	jne pci_real_nextdev
9964	cmp si, #0
9965	je pci_real_ok
9966	dec si
9967	pci_real_nextdev:
9968	inc ebx
9969	cmp ebx, #0x10000
9970	jne pci_real_devloop
9971	mov dx, cx
9972	shr ecx, #16
9973	mov ax, #0x8602
9974	jmp pci_real_fail
9975	pci_real_f03: ;; find class code
9976	cmp al, #0x03
9977	jne pci_real_f08
9978	xor ebx, ebx
9979	mov di, #0x08
9980	pci_real_devloop2:
9981	call pci_real_select_reg
9982	mov dx, #0x0cfc
9983	in eax, dx
9984	shr eax, #8
9985	cmp eax, ecx
9986	jne pci_real_nextdev2
9987	cmp si, #0
9988	je pci_real_ok
9989	dec si
9990	pci_real_nextdev2:
9991	inc ebx
9992	cmp ebx, #0x10000
9993	jne pci_real_devloop2
9994	mov dx, cx
9995	shr ecx, #16
9996	mov ax, #0x8603
9997	jmp pci_real_fail
9998	pci_real_f08: ;; read configuration byte
9999	cmp al, #0x08
10000	jne pci_real_f09
10001	call pci_real_select_reg
10002	push dx
10003	mov dx, di
10004	and dx, #0x03
10005	add dx, #0x0cfc
10006	in al, dx
10007	pop dx
10008	mov cl, al
10009	jmp pci_real_ok
10010	pci_real_f09: ;; read configuration word
10011	cmp al, #0x09
10012	jne pci_real_f0a
10013	call pci_real_select_reg
10014	push dx
10015	mov dx, di
10016	and dx, #0x02
10017	add dx, #0x0cfc
10018	in ax, dx
10019	pop dx
10020	mov cx, ax
10021	jmp pci_real_ok
10022	pci_real_f0a: ;; read configuration dword
10023	cmp al, #0x0a
10024	jne pci_real_f0b
10025	call pci_real_select_reg
10026	push dx
10027	mov dx, #0x0cfc
10028	in eax, dx
10029	pop dx
10030	mov ecx, eax
10031	jmp pci_real_ok
10032	pci_real_f0b: ;; write configuration byte
10033	cmp al, #0x0b
10034	jne pci_real_f0c
10035	call pci_real_select_reg
10036	push dx
10037	mov dx, di
10038	and dx, #0x03
10039	add dx, #0x0cfc
10040	mov al, cl
10041	out dx, al
10042	pop dx
10043	jmp pci_real_ok
10044	pci_real_f0c: ;; write configuration word
10045	cmp al, #0x0c
10046	jne pci_real_f0d
10047	call pci_real_select_reg
10048	push dx
10049	mov dx, di
10050	and dx, #0x02
10051	add dx, #0x0cfc
10052	mov ax, cx
10053	out dx, ax
10054	pop dx
10055	jmp pci_real_ok
10056	pci_real_f0d: ;; write configuration dword
10057	cmp al, #0x0d
10058	jne pci_real_f0e
10059	call pci_real_select_reg
10060	push dx
10061	mov dx, #0x0cfc
10062	mov eax, ecx
10063	out dx, eax
10064	pop dx
10065	jmp pci_real_ok
10066	pci_real_f0e: ;; get irq routing options
10067	cmp al, #0x0e
10068	jne pci_real_unknown
10069	SEG ES
10070	cmp word ptr [di], #pci_routing_table_structure_end - pci_routing_table_structure_start
10071	jb pci_real_too_small
10072	SEG ES
10073	mov word ptr [di], #pci_routing_table_structure_end - pci_routing_table_structure_start
10074	pushf
10075	push ds
10076	push es
10077	push cx
10078	push si
10079	push di
10080	cld
10081	mov si, #pci_routing_table_structure_start
10082	push cs
10083	pop ds
10084	SEG ES
10085	mov cx, [di+2]
10086	SEG ES
10087	mov es, [di+4]
10088	mov di, cx
10089	mov cx, #pci_routing_table_structure_end - pci_routing_table_structure_start
10090	rep
10091	movsb
10092	pop di
10093	pop si
10094	pop cx
10095	pop es
10096	pop ds
10097	popf
10098	mov bx, #(1 << 9) \| (1 << 11) ;; irq 9 and 11 are used
10099	jmp pci_real_ok
10100	pci_real_too_small:
10101	SEG ES
10102	mov word ptr [di], #pci_routing_table_structure_end - pci_routing_table_structure_start
10103	mov ah, #0x89
10104	jmp pci_real_fail
10105
10106	pci_real_unknown:
10107	mov ah, #0x81
10108	pci_real_fail:
10109	pop edi
10110	pop esi
10111	stc
10112	ret
10113	pci_real_ok:
10114	xor ah, ah
10115	pop edi
10116	pop esi
10117	clc
10118	ret
10119
10120	pci_real_select_reg:
10121	push dx
10122	mov eax, #0x800000
10123	mov ax, bx
10124	shl eax, #8
10125	and di, #0xff
10126	or ax, di
10127	and al, #0xfc
10128	mov dx, #0x0cf8
10129	out dx, eax
10130	pop dx
10131	ret
10132
10133	.align 16
10134	pci_routing_table_structure:
10135	db 0x24, 0x50, 0x49, 0x52 ;; "$PIR" signature
10136	db 0, 1 ;; version
10137	#ifdef VBOX
10138	#if 0
10139	dw 32 + (30 * 16) ;; table size
10140	#else
10141	dw 32 + (10 * 16) ;; table size
10142	#endif
10143	#else /* !VBOX */
10144	dw 32 + (6 * 16) ;; table size
10145	#endif /* !VBOX */
10146	db 0 ;; PCI interrupt router bus
10147	db 0x08 ;; PCI interrupt router DevFunc
10148	dw 0x0000 ;; PCI exclusive IRQs
10149	dw 0x8086 ;; compatible PCI interrupt router vendor ID
10150	dw 0x7000 ;; compatible PCI interrupt router device ID
10151	dw 0,0 ;; Miniport data
10152	db 0,0,0,0,0,0,0,0,0,0,0 ;; reserved
10153	#ifdef VBOX
10154	db 0x00 ;; checksum (set by biossums)
10155	#else /* !VBOX */
10156	db 0x07 ;; checksum
10157	#endif /* !VBOX */
10158	pci_routing_table_structure_start:
10159	;; first slot entry PCI-to-ISA (embedded)
10160	db 0 ;; pci bus number
10161	db 0x08 ;; pci device number (bit 7-3)
10162	db 0x60 ;; link value INTA#: pointer into PCI2ISA config space
10163	dw 0xdef8 ;; IRQ bitmap INTA#
10164	db 0x61 ;; link value INTB#
10165	dw 0xdef8 ;; IRQ bitmap INTB#
10166	db 0x62 ;; link value INTC#
10167	dw 0xdef8 ;; IRQ bitmap INTC#
10168	db 0x63 ;; link value INTD#
10169	dw 0xdef8 ;; IRQ bitmap INTD#
10170	db 0 ;; physical slot (0 = embedded)
10171	db 0 ;; reserved
10172	;; second slot entry: 1st PCI slot
10173	db 0 ;; pci bus number
10174	db 0x10 ;; pci device number (bit 7-3)
10175	db 0x61 ;; link value INTA#
10176	dw 0xdef8 ;; IRQ bitmap INTA#
10177	db 0x62 ;; link value INTB#
10178	dw 0xdef8 ;; IRQ bitmap INTB#
10179	db 0x63 ;; link value INTC#
10180	dw 0xdef8 ;; IRQ bitmap INTC#
10181	db 0x60 ;; link value INTD#
10182	dw 0xdef8 ;; IRQ bitmap INTD#
10183	db 1 ;; physical slot (0 = embedded)
10184	db 0 ;; reserved
10185	;; third slot entry: 2nd PCI slot
10186	db 0 ;; pci bus number
10187	db 0x18 ;; pci device number (bit 7-3)
10188	db 0x62 ;; link value INTA#
10189	dw 0xdef8 ;; IRQ bitmap INTA#
10190	db 0x63 ;; link value INTB#
10191	dw 0xdef8 ;; IRQ bitmap INTB#
10192	db 0x60 ;; link value INTC#
10193	dw 0xdef8 ;; IRQ bitmap INTC#
10194	db 0x61 ;; link value INTD#
10195	dw 0xdef8 ;; IRQ bitmap INTD#
10196	db 2 ;; physical slot (0 = embedded)
10197	db 0 ;; reserved
10198	;; 4th slot entry: 3rd PCI slot
10199	db 0 ;; pci bus number
10200	db 0x20 ;; pci device number (bit 7-3)
10201	db 0x63 ;; link value INTA#
10202	dw 0xdef8 ;; IRQ bitmap INTA#
10203	db 0x60 ;; link value INTB#
10204	dw 0xdef8 ;; IRQ bitmap INTB#
10205	db 0x61 ;; link value INTC#
10206	dw 0xdef8 ;; IRQ bitmap INTC#
10207	db 0x62 ;; link value INTD#
10208	dw 0xdef8 ;; IRQ bitmap INTD#
10209	db 3 ;; physical slot (0 = embedded)
10210	db 0 ;; reserved
10211	;; 5th slot entry: 4rd PCI slot
10212	db 0 ;; pci bus number
10213	db 0x28 ;; pci device number (bit 7-3)
10214	db 0x60 ;; link value INTA#
10215	dw 0xdef8 ;; IRQ bitmap INTA#
10216	db 0x61 ;; link value INTB#
10217	dw 0xdef8 ;; IRQ bitmap INTB#
10218	db 0x62 ;; link value INTC#
10219	dw 0xdef8 ;; IRQ bitmap INTC#
10220	db 0x63 ;; link value INTD#
10221	dw 0xdef8 ;; IRQ bitmap INTD#
10222	db 4 ;; physical slot (0 = embedded)
10223	db 0 ;; reserved
10224	;; 6th slot entry: 5rd PCI slot
10225	db 0 ;; pci bus number
10226	db 0x30 ;; pci device number (bit 7-3)
10227	db 0x61 ;; link value INTA#
10228	dw 0xdef8 ;; IRQ bitmap INTA#
10229	db 0x62 ;; link value INTB#
10230	dw 0xdef8 ;; IRQ bitmap INTB#
10231	db 0x63 ;; link value INTC#
10232	dw 0xdef8 ;; IRQ bitmap INTC#
10233	db 0x60 ;; link value INTD#
10234	dw 0xdef8 ;; IRQ bitmap INTD#
10235	db 5 ;; physical slot (0 = embedded)
10236	db 0 ;; reserved
10237	#ifdef VBOX
10238	;; 7th slot entry: 6th PCI slot
10239	db 0 ;; pci bus number
10240	db 0x38 ;; pci device number (bit 7-3)
10241	db 0x62 ;; link value INTA#
10242	dw 0xdef8 ;; IRQ bitmap INTA#
10243	db 0x63 ;; link value INTB#
10244	dw 0xdef8 ;; IRQ bitmap INTB#
10245	db 0x60 ;; link value INTC#
10246	dw 0xdef8 ;; IRQ bitmap INTC#
10247	db 0x61 ;; link value INTD#
10248	dw 0xdef8 ;; IRQ bitmap INTD#
10249	db 6 ;; physical slot (0 = embedded)
10250	db 0 ;; reserved
10251	;; 8th slot entry: 7th PCI slot
10252	db 0 ;; pci bus number
10253	db 0x40 ;; pci device number (bit 7-3)
10254	db 0x63 ;; link value INTA#
10255	dw 0xdef8 ;; IRQ bitmap INTA#
10256	db 0x60 ;; link value INTB#
10257	dw 0xdef8 ;; IRQ bitmap INTB#
10258	db 0x61 ;; link value INTC#
10259	dw 0xdef8 ;; IRQ bitmap INTC#
10260	db 0x62 ;; link value INTD#
10261	dw 0xdef8 ;; IRQ bitmap INTD#
10262	db 7 ;; physical slot (0 = embedded)
10263	db 0 ;; reserved
10264	;; 9th slot entry: 8th PCI slot
10265	db 0 ;; pci bus number
10266	db 0x48 ;; pci device number (bit 7-3)
10267	db 0x60 ;; link value INTA#
10268	dw 0xdef8 ;; IRQ bitmap INTA#
10269	db 0x61 ;; link value INTB#
10270	dw 0xdef8 ;; IRQ bitmap INTB#
10271	db 0x62 ;; link value INTC#
10272	dw 0xdef8 ;; IRQ bitmap INTC#
10273	db 0x63 ;; link value INTD#
10274	dw 0xdef8 ;; IRQ bitmap INTD#
10275	db 8 ;; physical slot (0 = embedded)
10276	db 0 ;; reserved
10277	;; 10th slot entry: 9th PCI slot
10278	db 0 ;; pci bus number
10279	db 0x50 ;; pci device number (bit 7-3)
10280	db 0x61 ;; link value INTA#
10281	dw 0xdef8 ;; IRQ bitmap INTA#
10282	db 0x62 ;; link value INTB#
10283	dw 0xdef8 ;; IRQ bitmap INTB#
10284	db 0x63 ;; link value INTC#
10285	dw 0xdef8 ;; IRQ bitmap INTC#
10286	db 0x60 ;; link value INTD#
10287	dw 0xdef8 ;; IRQ bitmap INTD#
10288	db 9 ;; physical slot (0 = embedded)
10289	db 0 ;; reserved
10290	;; 11th slot entry: 10th PCI slot
10291	db 0 ;; pci bus number
10292	db 0x58 ;; pci device number (bit 7-3)
10293	db 0x61 ;; link value INTA#
10294	dw 0xdef8 ;; IRQ bitmap INTA#
10295	db 0x62 ;; link value INTB#
10296	dw 0xdef8 ;; IRQ bitmap INTB#
10297	db 0x63 ;; link value INTC#
10298	dw 0xdef8 ;; IRQ bitmap INTC#
10299	db 0x60 ;; link value INTD#
10300	dw 0xdef8 ;; IRQ bitmap INTD#
10301	db 10 ;; physical slot (0 = embedded)
10302	db 0 ;; reserved
10303	;; 12th slot entry: 11th PCI slot
10304	db 0 ;; pci bus number
10305	db 0x60 ;; pci device number (bit 7-3)
10306	db 0x61 ;; link value INTA#
10307	dw 0xdef8 ;; IRQ bitmap INTA#
10308	db 0x62 ;; link value INTB#
10309	dw 0xdef8 ;; IRQ bitmap INTB#
10310	db 0x63 ;; link value INTC#
10311	dw 0xdef8 ;; IRQ bitmap INTC#
10312	db 0x60 ;; link value INTD#
10313	dw 0xdef8 ;; IRQ bitmap INTD#
10314	db 11 ;; physical slot (0 = embedded)
10315	db 0 ;; reserved
10316	;; 13th slot entry: 12th PCI slot
10317	db 0 ;; pci bus number
10318	db 0x68 ;; pci device number (bit 7-3)
10319	db 0x61 ;; link value INTA#
10320	dw 0xdef8 ;; IRQ bitmap INTA#
10321	db 0x62 ;; link value INTB#
10322	dw 0xdef8 ;; IRQ bitmap INTB#
10323	db 0x63 ;; link value INTC#
10324	dw 0xdef8 ;; IRQ bitmap INTC#
10325	db 0x60 ;; link value INTD#
10326	dw 0xdef8 ;; IRQ bitmap INTD#
10327	db 12 ;; physical slot (0 = embedded)
10328	db 0 ;; reserved
10329	;; 14th slot entry: 13th PCI slot
10330	db 0 ;; pci bus number
10331	db 0x70 ;; pci device number (bit 7-3)
10332	db 0x61 ;; link value INTA#
10333	dw 0xdef8 ;; IRQ bitmap INTA#
10334	db 0x62 ;; link value INTB#
10335	dw 0xdef8 ;; IRQ bitmap INTB#
10336	db 0x63 ;; link value INTC#
10337	dw 0xdef8 ;; IRQ bitmap INTC#
10338	db 0x60 ;; link value INTD#
10339	dw 0xdef8 ;; IRQ bitmap INTD#
10340	db 13 ;; physical slot (0 = embedded)
10341	db 0 ;; reserved
10342	;; 15th slot entry: 14th PCI slot
10343	db 0 ;; pci bus number
10344	db 0x78 ;; pci device number (bit 7-3)
10345	db 0x61 ;; link value INTA#
10346	dw 0xdef8 ;; IRQ bitmap INTA#
10347	db 0x62 ;; link value INTB#
10348	dw 0xdef8 ;; IRQ bitmap INTB#
10349	db 0x63 ;; link value INTC#
10350	dw 0xdef8 ;; IRQ bitmap INTC#
10351	db 0x60 ;; link value INTD#
10352	dw 0xdef8 ;; IRQ bitmap INTD#
10353	db 14 ;; physical slot (0 = embedded)
10354	db 0 ;; reserved
10355	;; 16th slot entry: 15th PCI slot
10356	db 0 ;; pci bus number
10357	db 0x80 ;; pci device number (bit 7-3)
10358	db 0x61 ;; link value INTA#
10359	dw 0xdef8 ;; IRQ bitmap INTA#
10360	db 0x62 ;; link value INTB#
10361	dw 0xdef8 ;; IRQ bitmap INTB#
10362	db 0x63 ;; link value INTC#
10363	dw 0xdef8 ;; IRQ bitmap INTC#
10364	db 0x60 ;; link value INTD#
10365	dw 0xdef8 ;; IRQ bitmap INTD#
10366	db 15 ;; physical slot (0 = embedded)
10367	db 0 ;; reserved
10368	;; 17th slot entry: 16th PCI slot
10369	db 0 ;; pci bus number
10370	db 0x88 ;; pci device number (bit 7-3)
10371	db 0x61 ;; link value INTA#
10372	dw 0xdef8 ;; IRQ bitmap INTA#
10373	db 0x62 ;; link value INTB#
10374	dw 0xdef8 ;; IRQ bitmap INTB#
10375	db 0x63 ;; link value INTC#
10376	dw 0xdef8 ;; IRQ bitmap INTC#
10377	db 0x60 ;; link value INTD#
10378	dw 0xdef8 ;; IRQ bitmap INTD#
10379	db 16 ;; physical slot (0 = embedded)
10380	db 0 ;; reserved
10381	;; 18th slot entry: 17th PCI slot
10382	db 0 ;; pci bus number
10383	db 0x90 ;; pci device number (bit 7-3)
10384	db 0x61 ;; link value INTA#
10385	dw 0xdef8 ;; IRQ bitmap INTA#
10386	db 0x62 ;; link value INTB#
10387	dw 0xdef8 ;; IRQ bitmap INTB#
10388	db 0x63 ;; link value INTC#
10389	dw 0xdef8 ;; IRQ bitmap INTC#
10390	db 0x60 ;; link value INTD#
10391	dw 0xdef8 ;; IRQ bitmap INTD#
10392	db 17 ;; physical slot (0 = embedded)
10393	db 0 ;; reserved
10394	;; 19th slot entry: 18th PCI slot
10395	db 0 ;; pci bus number
10396	db 0x98 ;; pci device number (bit 7-3)
10397	db 0x61 ;; link value INTA#
10398	dw 0xdef8 ;; IRQ bitmap INTA#
10399	db 0x62 ;; link value INTB#
10400	dw 0xdef8 ;; IRQ bitmap INTB#
10401	db 0x63 ;; link value INTC#
10402	dw 0xdef8 ;; IRQ bitmap INTC#
10403	db 0x60 ;; link value INTD#
10404	dw 0xdef8 ;; IRQ bitmap INTD#
10405	db 18 ;; physical slot (0 = embedded)
10406	db 0 ;; reserved
10407	;; 20th slot entry: 19th PCI slot
10408	db 0 ;; pci bus number
10409	db 0xa0 ;; pci device number (bit 7-3)
10410	db 0x61 ;; link value INTA#
10411	dw 0xdef8 ;; IRQ bitmap INTA#
10412	db 0x62 ;; link value INTB#
10413	dw 0xdef8 ;; IRQ bitmap INTB#
10414	db 0x63 ;; link value INTC#
10415	dw 0xdef8 ;; IRQ bitmap INTC#
10416	db 0x60 ;; link value INTD#
10417	dw 0xdef8 ;; IRQ bitmap INTD#
10418	db 19 ;; physical slot (0 = embedded)
10419	db 0 ;; reserved
10420	;; 21th slot entry: 20th PCI slot
10421	db 0 ;; pci bus number
10422	db 0xa8 ;; pci device number (bit 7-3)
10423	db 0x61 ;; link value INTA#
10424	dw 0xdef8 ;; IRQ bitmap INTA#
10425	db 0x62 ;; link value INTB#
10426	dw 0xdef8 ;; IRQ bitmap INTB#
10427	db 0x63 ;; link value INTC#
10428	dw 0xdef8 ;; IRQ bitmap INTC#
10429	db 0x60 ;; link value INTD#
10430	dw 0xdef8 ;; IRQ bitmap INTD#
10431	db 20 ;; physical slot (0 = embedded)
10432	db 0 ;; reserved
10433	;; 21th slot entry: 20th PCI slot
10434	db 0 ;; pci bus number
10435	db 0xb0 ;; pci device number (bit 7-3)
10436	db 0x61 ;; link value INTA#
10437	dw 0xdef8 ;; IRQ bitmap INTA#
10438	db 0x62 ;; link value INTB#
10439	dw 0xdef8 ;; IRQ bitmap INTB#
10440	db 0x63 ;; link value INTC#
10441	dw 0xdef8 ;; IRQ bitmap INTC#
10442	db 0x60 ;; link value INTD#
10443	dw 0xdef8 ;; IRQ bitmap INTD#
10444	db 20 ;; physical slot (0 = embedded)
10445	db 0 ;; reserved
10446	;; 22th slot entry: 21th PCI slot
10447	db 0 ;; pci bus number
10448	db 0xb8 ;; pci device number (bit 7-3)
10449	db 0x61 ;; link value INTA#
10450	dw 0xdef8 ;; IRQ bitmap INTA#
10451	db 0x62 ;; link value INTB#
10452	dw 0xdef8 ;; IRQ bitmap INTB#
10453	db 0x63 ;; link value INTC#
10454	dw 0xdef8 ;; IRQ bitmap INTC#
10455	db 0x60 ;; link value INTD#
10456	dw 0xdef8 ;; IRQ bitmap INTD#
10457	db 21 ;; physical slot (0 = embedded)
10458	db 0 ;; reserved
10459	;; 23th slot entry: 22th PCI slot
10460	db 0 ;; pci bus number
10461	db 0xc0 ;; pci device number (bit 7-3)
10462	db 0x61 ;; link value INTA#
10463	dw 0xdef8 ;; IRQ bitmap INTA#
10464	db 0x62 ;; link value INTB#
10465	dw 0xdef8 ;; IRQ bitmap INTB#
10466	db 0x63 ;; link value INTC#
10467	dw 0xdef8 ;; IRQ bitmap INTC#
10468	db 0x60 ;; link value INTD#
10469	dw 0xdef8 ;; IRQ bitmap INTD#
10470	db 22 ;; physical slot (0 = embedded)
10471	db 0 ;; reserved
10472	;; 24th slot entry: 23th PCI slot
10473	db 0 ;; pci bus number
10474	db 0xc8 ;; pci device number (bit 7-3)
10475	db 0x61 ;; link value INTA#
10476	dw 0xdef8 ;; IRQ bitmap INTA#
10477	db 0x62 ;; link value INTB#
10478	dw 0xdef8 ;; IRQ bitmap INTB#
10479	db 0x63 ;; link value INTC#
10480	dw 0xdef8 ;; IRQ bitmap INTC#
10481	db 0x60 ;; link value INTD#
10482	dw 0xdef8 ;; IRQ bitmap INTD#
10483	db 23 ;; physical slot (0 = embedded)
10484	db 0 ;; reserved
10485	;; 25th slot entry: 24th PCI slot
10486	db 0 ;; pci bus number
10487	db 0xd0 ;; pci device number (bit 7-3)
10488	db 0x61 ;; link value INTA#
10489	dw 0xdef8 ;; IRQ bitmap INTA#
10490	db 0x62 ;; link value INTB#
10491	dw 0xdef8 ;; IRQ bitmap INTB#
10492	db 0x63 ;; link value INTC#
10493	dw 0xdef8 ;; IRQ bitmap INTC#
10494	db 0x60 ;; link value INTD#
10495	dw 0xdef8 ;; IRQ bitmap INTD#
10496	db 24 ;; physical slot (0 = embedded)
10497	db 0 ;; reserved
10498	;; 26th slot entry: 25th PCI slot
10499	db 0 ;; pci bus number
10500	db 0xd8 ;; pci device number (bit 7-3)
10501	db 0x61 ;; link value INTA#
10502	dw 0xdef8 ;; IRQ bitmap INTA#
10503	db 0x62 ;; link value INTB#
10504	dw 0xdef8 ;; IRQ bitmap INTB#
10505	db 0x63 ;; link value INTC#
10506	dw 0xdef8 ;; IRQ bitmap INTC#
10507	db 0x60 ;; link value INTD#
10508	dw 0xdef8 ;; IRQ bitmap INTD#
10509	db 25 ;; physical slot (0 = embedded)
10510	db 0 ;; reserved
10511	;; 27th slot entry: 26th PCI slot
10512	db 0 ;; pci bus number
10513	db 0xe0 ;; pci device number (bit 7-3)
10514	db 0x61 ;; link value INTA#
10515	dw 0xdef8 ;; IRQ bitmap INTA#
10516	db 0x62 ;; link value INTB#
10517	dw 0xdef8 ;; IRQ bitmap INTB#
10518	db 0x63 ;; link value INTC#
10519	dw 0xdef8 ;; IRQ bitmap INTC#
10520	db 0x60 ;; link value INTD#
10521	dw 0xdef8 ;; IRQ bitmap INTD#
10522	db 26 ;; physical slot (0 = embedded)
10523	db 0 ;; reserved
10524	;; 28th slot entry: 27th PCI slot
10525	db 0 ;; pci bus number
10526	db 0xe8 ;; pci device number (bit 7-3)
10527	db 0x61 ;; link value INTA#
10528	dw 0xdef8 ;; IRQ bitmap INTA#
10529	db 0x62 ;; link value INTB#
10530	dw 0xdef8 ;; IRQ bitmap INTB#
10531	db 0x63 ;; link value INTC#
10532	dw 0xdef8 ;; IRQ bitmap INTC#
10533	db 0x60 ;; link value INTD#
10534	dw 0xdef8 ;; IRQ bitmap INTD#
10535	db 27 ;; physical slot (0 = embedded)
10536	db 0 ;; reserved
10537	;; 29th slot entry: 28th PCI slot
10538	db 0 ;; pci bus number
10539	db 0xf0 ;; pci device number (bit 7-3)
10540	db 0x61 ;; link value INTA#
10541	dw 0xdef8 ;; IRQ bitmap INTA#
10542	db 0x62 ;; link value INTB#
10543	dw 0xdef8 ;; IRQ bitmap INTB#
10544	db 0x63 ;; link value INTC#
10545	dw 0xdef8 ;; IRQ bitmap INTC#
10546	db 0x60 ;; link value INTD#
10547	dw 0xdef8 ;; IRQ bitmap INTD#
10548	db 28 ;; physical slot (0 = embedded)
10549	db 0 ;; reserved
10550	;; 30th slot entry: 29th PCI slot
10551	db 0 ;; pci bus number
10552	db 0xf8 ;; pci device number (bit 7-3)
10553	db 0x61 ;; link value INTA#
10554	dw 0xdef8 ;; IRQ bitmap INTA#
10555	db 0x62 ;; link value INTB#
10556	dw 0xdef8 ;; IRQ bitmap INTB#
10557	db 0x63 ;; link value INTC#
10558	dw 0xdef8 ;; IRQ bitmap INTC#
10559	db 0x60 ;; link value INTD#
10560	dw 0xdef8 ;; IRQ bitmap INTD#
10561	db 29 ;; physical slot (0 = embedded)
10562	db 0 ;; reserved
10563	#endif /* VBOX */
10564	pci_routing_table_structure_end:
10565
10566	#if !BX_ROMBIOS32
10567	pci_irq_list:
10568	db 11, 10, 9, 5;
10569
10570	pcibios_init_sel_reg:
10571	push eax
10572	mov eax, #0x800000
10573	mov ax, bx
10574	shl eax, #8
10575	and dl, #0xfc
10576	or al, dl
10577	mov dx, #0x0cf8
10578	out dx, eax
10579	pop eax
10580	ret
10581
10582	pcibios_init_iomem_bases:
10583	push bp
10584	mov bp, sp
10585	mov eax, #0xe0000000 ;; base for memory init
10586	push eax
10587	mov ax, #0xc000 ;; base for i/o init
10588	push ax
10589	mov ax, #0x0010 ;; start at base address #0
10590	push ax
10591	mov bx, #0x0008
10592	pci_init_io_loop1:
10593	mov dl, #0x00
10594	call pcibios_init_sel_reg
10595	mov dx, #0x0cfc
10596	in ax, dx
10597	cmp ax, #0xffff
10598	jz next_pci_dev
10599	#ifndef VBOX /* This currently breaks restoring a previously saved state. */
10600	mov dl, #0x04 ;; disable i/o and memory space access
10601	call pcibios_init_sel_reg
10602	mov dx, #0x0cfc
10603	in al, dx
10604	and al, #0xfc
10605	out dx, al
10606	pci_init_io_loop2:
10607	mov dl, [bp-8]
10608	call pcibios_init_sel_reg
10609	mov dx, #0x0cfc
10610	in eax, dx
10611	test al, #0x01
10612	jnz init_io_base
10613	mov ecx, eax
10614	mov eax, #0xffffffff
10615	out dx, eax
10616	in eax, dx
10617	cmp eax, ecx
10618	je next_pci_base
10619	xor eax, #0xffffffff
10620	mov ecx, eax
10621	mov eax, [bp-4]
10622	out dx, eax
10623	add eax, ecx ;; calculate next free mem base
10624	add eax, #0x01000000
10625	and eax, #0xff000000
10626	mov [bp-4], eax
10627	jmp next_pci_base
10628	init_io_base:
10629	mov cx, ax
10630	mov ax, #0xffff
10631	out dx, ax
10632	in ax, dx
10633	cmp ax, cx
10634	je next_pci_base
10635	xor ax, #0xfffe
10636	mov cx, ax
10637	mov ax, [bp-6]
10638	out dx, ax
10639	add ax, cx ;; calculate next free i/o base
10640	add ax, #0x0100
10641	and ax, #0xff00
10642	mov [bp-6], ax
10643	next_pci_base:
10644	mov al, [bp-8]
10645	add al, #0x04
10646	cmp al, #0x28
10647	je enable_iomem_space
10648	mov byte ptr[bp-8], al
10649	jmp pci_init_io_loop2
10650	#endif /* !VBOX */
10651	enable_iomem_space:
10652	mov dl, #0x04 ;; enable i/o and memory space access if available
10653	call pcibios_init_sel_reg
10654	mov dx, #0x0cfc
10655	in al, dx
10656	or al, #0x07
10657	out dx, al
10658	#ifdef VBOX
10659	mov dl, #0x00 ;; check if PCI device is AMD PCNet
10660	call pcibios_init_sel_reg
10661	mov dx, #0x0cfc
10662	in eax, dx
10663	cmp eax, #0x20001022
10664	jne next_pci_dev
10665	mov dl, #0x10 ;; get I/O address
10666	call pcibios_init_sel_reg
10667	mov dx, #0x0cfc
10668	in ax, dx
10669	and ax, #0xfffc
10670	mov cx, ax
10671	mov dx, cx
10672	add dx, #0x14 ;; reset register if PCNet is in word I/O mode
10673	in ax, dx ;; reset is performed by reading the reset register
10674	mov dx, cx
10675	add dx, #0x18 ;; reset register if PCNet is in word I/O mode
10676	in eax, dx ;; reset is performed by reading the reset register
10677	#endif /* VBOX */
10678	next_pci_dev:
10679	mov byte ptr[bp-8], #0x10
10680	inc bx
10681	cmp bx, #0x0100
10682	jne pci_init_io_loop1
10683	mov sp, bp
10684	pop bp
10685	ret
10686
10687	pcibios_init_set_elcr:
10688	push ax
10689	push cx
10690	mov dx, #0x04d0
10691	test al, #0x08
10692	jz is_master_pic
10693	inc dx
10694	and al, #0x07
10695	is_master_pic:
10696	mov cl, al
10697	mov bl, #0x01
10698	shl bl, cl
10699	in al, dx
10700	or al, bl
10701	out dx, al
10702	pop cx
10703	pop ax
10704	ret
10705
10706	pcibios_init_irqs:
10707	push ds
10708	push bp
10709	mov ax, #0xf000
10710	mov ds, ax
10711	mov dx, #0x04d0 ;; reset ELCR1 + ELCR2
10712	mov al, #0x00
10713	out dx, al
10714	inc dx
10715	out dx, al
10716	mov si, #pci_routing_table_structure
10717	mov bh, [si+8]
10718	mov bl, [si+9]
10719	mov dl, #0x00
10720	call pcibios_init_sel_reg
10721	mov dx, #0x0cfc
10722	in eax, dx
10723	cmp eax, [si+12] ;; check irq router
10724	jne pci_init_end
10725	mov dl, [si+34]
10726	call pcibios_init_sel_reg
10727	push bx ;; save irq router bus + devfunc
10728	mov dx, #0x0cfc
10729	mov ax, #0x8080
10730	out dx, ax ;; reset PIRQ route control
10731	inc dx
10732	inc dx
10733	out dx, ax
10734	mov ax, [si+6]
10735	sub ax, #0x20
10736	shr ax, #4
10737	mov cx, ax
10738	add si, #0x20 ;; set pointer to 1st entry
10739	mov bp, sp
10740	mov ax, #pci_irq_list
10741	push ax
10742	xor ax, ax
10743	push ax
10744	pci_init_irq_loop1:
10745	mov bh, [si]
10746	mov bl, [si+1]
10747	pci_init_irq_loop2:
10748	mov dl, #0x00
10749	call pcibios_init_sel_reg
10750	mov dx, #0x0cfc
10751	in ax, dx
10752	cmp ax, #0xffff
10753	jnz pci_test_int_pin
10754	test bl, #0x07
10755	jz next_pir_entry
10756	jmp next_pci_func
10757	pci_test_int_pin:
10758	mov dl, #0x3c
10759	call pcibios_init_sel_reg
10760	mov dx, #0x0cfd
10761	in al, dx
10762	and al, #0x07
10763	jz next_pci_func
10764	dec al ;; determine pirq reg
10765	mov dl, #0x03
10766	mul al, dl
10767	add al, #0x02
10768	xor ah, ah
10769	mov bx, ax
10770	mov al, [si+bx]
10771	mov dl, al
10772	mov bx, [bp]
10773	call pcibios_init_sel_reg
10774	mov dx, #0x0cfc
10775	and al, #0x03
10776	add dl, al
10777	in al, dx
10778	cmp al, #0x80
10779	jb pirq_found
10780	mov bx, [bp-2] ;; pci irq list pointer
10781	mov al, [bx]
10782	out dx, al
10783	inc bx
10784	mov [bp-2], bx
10785	call pcibios_init_set_elcr
10786	pirq_found:
10787	mov bh, [si]
10788	mov bl, [si+1]
10789	add bl, [bp-3] ;; pci function number
10790	mov dl, #0x3c
10791	call pcibios_init_sel_reg
10792	mov dx, #0x0cfc
10793	out dx, al
10794	next_pci_func:
10795	inc byte ptr[bp-3]
10796	inc bl
10797	test bl, #0x07
10798	jnz pci_init_irq_loop2
10799	next_pir_entry:
10800	add si, #0x10
10801	mov byte ptr[bp-3], #0x00
10802	loop pci_init_irq_loop1
10803	mov sp, bp
10804	pop bx
10805	pci_init_end:
10806	pop bp
10807	pop ds
10808	ret
10809	#endif // BX_ROMBIOS32
10810	#endif // BX_PCIBIOS
10811
10812	#if BX_ROMBIOS32
10813	rombios32_init:
10814	;; save a20 and enable it
10815	in al, 0x92
10816	push ax
10817	or al, #0x02
10818	out 0x92, al
10819
10820	;; save SS:SP to the BDA
10821	xor ax, ax
10822	mov ds, ax
10823	mov 0x0469, ss
10824	mov 0x0467, sp
10825
10826	SEG CS
10827	lidt [pmode_IDT_info]
10828	SEG CS
10829	lgdt [rombios32_gdt_48]
10830	;; set PE bit in CR0
10831	mov eax, cr0
10832	or al, #0x01
10833	mov cr0, eax
10834	;; start protected mode code: ljmpl 0x10:rombios32_init1
10835	db 0x66, 0xea
10836	dw rombios32_05
10837	dw 0x000f ;; high 16 bit address
10838	dw 0x0010
10839
10840	use32 386
10841	rombios32_05:
10842	;; init data segments
10843	mov eax, #0x18
10844	mov ds, ax
10845	mov es, ax
10846	mov ss, ax
10847	xor eax, eax
10848	mov fs, ax
10849	mov gs, ax
10850	cld
10851
10852	;; copy rombios32 code to ram (ram offset = 1MB)
10853	mov esi, #0xfffe0000
10854	mov edi, #0x00040000
10855	mov ecx, #0x10000 / 4
10856	rep
10857	movsd
10858
10859	;; init the stack pointer
10860	mov esp, #0x00080000
10861
10862	;; call rombios32 code
10863	mov eax, #0x00040000
10864	call eax
10865
10866	;; return to 16 bit protected mode first
10867	db 0xea
10868	dd rombios32_10
10869	dw 0x20
10870
10871	use16 386
10872	rombios32_10:
10873	;; restore data segment limits to 0xffff
10874	mov ax, #0x28
10875	mov ds, ax
10876	mov es, ax
10877	mov ss, ax
10878	mov fs, ax
10879	mov gs, ax
10880
10881	;; reset PE bit in CR0
10882	mov eax, cr0
10883	and al, #0xFE
10884	mov cr0, eax
10885
10886	;; far jump to flush CPU queue after transition to real mode
10887	JMP_AP(0xf000, rombios32_real_mode)
10888
10889	rombios32_real_mode:
10890	;; restore IDT to normal real-mode defaults
10891	SEG CS
10892	lidt [rmode_IDT_info]
10893
10894	xor ax, ax
10895	mov ds, ax
10896	mov es, ax
10897	mov fs, ax
10898	mov gs, ax
10899
10900	;; restore SS:SP from the BDA
10901	mov ss, 0x0469
10902	xor esp, esp
10903	mov sp, 0x0467
10904	;; restore a20
10905	pop ax
10906	out 0x92, al
10907	ret
10908
10909	rombios32_gdt_48:
10910	dw 0x30
10911	dw rombios32_gdt
10912	dw 0x000f
10913
10914	rombios32_gdt:
10915	dw 0, 0, 0, 0
10916	dw 0, 0, 0, 0
10917	dw 0xffff, 0, 0x9b00, 0x00cf ; 32 bit flat code segment (0x10)
10918	dw 0xffff, 0, 0x9300, 0x00cf ; 32 bit flat data segment (0x18)
10919	dw 0xffff, 0, 0x9b0f, 0x0000 ; 16 bit code segment base=0xf0000 limit=0xffff
10920	dw 0xffff, 0, 0x9300, 0x0000 ; 16 bit data segment base=0x0 limit=0xffff
10921	#endif
10922
10923
10924	; parallel port detection: base address in DX, index in BX, timeout in CL
10925	detect_parport:
10926	push dx
10927	add dx, #2
10928	in al, dx
10929	and al, #0xdf ; clear input mode
10930	out dx, al
10931	pop dx
10932	mov al, #0xaa
10933	out dx, al
10934	in al, dx
10935	cmp al, #0xaa
10936	jne no_parport
10937	push bx
10938	shl bx, #1
10939	mov [bx+0x408], dx ; Parallel I/O address
10940	pop bx
10941	mov [bx+0x478], cl ; Parallel printer timeout
10942	inc bx
10943	no_parport:
10944	ret
10945
10946	; serial port detection: base address in DX, index in BX, timeout in CL
10947	detect_serial:
10948	push dx
10949	inc dx
10950	mov al, #0x02
10951	out dx, al
10952	in al, dx
10953	cmp al, #0x02
10954	jne no_serial
10955	inc dx
10956	in al, dx
10957	cmp al, #0x02
10958	jne no_serial
10959	dec dx
10960	xor al, al
10961	out dx, al
10962	pop dx
10963	push bx
10964	shl bx, #1
10965	mov [bx+0x400], dx ; Serial I/O address
10966	pop bx
10967	mov [bx+0x47c], cl ; Serial timeout
10968	inc bx
10969	ret
10970	no_serial:
10971	pop dx
10972	ret
10973
10974	rom_checksum:
10975	push ax
10976	push bx
10977	push cx
10978	xor ax, ax
10979	xor bx, bx
10980	xor cx, cx
10981	mov ch, [2]
10982	shl cx, #1
10983	checksum_loop:
10984	add al, [bx]
10985	inc bx
10986	loop checksum_loop
10987	and al, #0xff
10988	pop cx
10989	pop bx
10990	pop ax
10991	ret
10992
10993	rom_scan:
10994	;; Scan for existence of valid expansion ROMS.
10995	;; Video ROM: from 0xC0000..0xC7FFF in 2k increments
10996	;; General ROM: from 0xC8000..0xDFFFF in 2k increments
10997	;; System ROM: only 0xE0000
10998	;;
10999	;; Header:
11000	;; Offset Value
11001	;; 0 0x55
11002	;; 1 0xAA
11003	;; 2 ROM length in 512-byte blocks
11004	;; 3 ROM initialization entry point (FAR CALL)
11005
11006	mov cx, #0xc000
11007	rom_scan_loop:
11008	mov ds, cx
11009	mov ax, #0x0004 ;; start with increment of 4 (512-byte) blocks = 2k
11010	cmp [0], #0xAA55 ;; look for signature
11011	jne rom_scan_increment
11012	call rom_checksum
11013	jnz rom_scan_increment
11014	mov al, [2] ;; change increment to ROM length in 512-byte blocks
11015
11016	;; We want our increment in 512-byte quantities, rounded to
11017	;; the nearest 2k quantity, since we only scan at 2k intervals.
11018	test al, #0x03
11019	jz block_count_rounded
11020	and al, #0xfc ;; needs rounding up
11021	add al, #0x04
11022	block_count_rounded:
11023
11024	xor bx, bx ;; Restore DS back to 0000:
11025	mov ds, bx
11026	push ax ;; Save AX
11027	;; Push addr of ROM entry point
11028	push cx ;; Push seg
11029	push #0x0003 ;; Push offset
11030	mov bp, sp ;; Call ROM init routine using seg:off on stack
11031	db 0xff ;; call_far ss:[bp+0]
11032	db 0x5e
11033	db 0
11034	cli ;; In case expansion ROM BIOS turns IF on
11035	add sp, #2 ;; Pop offset value
11036	pop cx ;; Pop seg value (restore CX)
11037	pop ax ;; Restore AX
11038	rom_scan_increment:
11039	shl ax, #5 ;; convert 512-bytes blocks to 16-byte increments
11040	;; because the segment selector is shifted left 4 bits.
11041	add cx, ax
11042	cmp cx, #0xe800 ;; Must encompass VBOX_LANBOOT_SEG!
11043	jbe rom_scan_loop
11044
11045	xor ax, ax ;; Restore DS back to 0000:
11046	mov ds, ax
11047	ret
11048
11049	;; for 'C' strings and other data, insert them here with
11050	;; a the following hack:
11051	;; DATA_SEG_DEFS_HERE
11052
11053
11054	;; the following area can be used to write dynamically generated tables
11055	.align 16
11056	bios_table_area_start:
11057	dd 0xaafb4442
11058	dd bios_table_area_end - bios_table_area_start - 8;
11059
11060	;--------
11061	;- POST -
11062	;--------
11063	.org 0xe05b ; POST Entry Point
11064	bios_table_area_end:
11065	post:
11066
11067	xor ax, ax
11068
11069	;; first reset the DMA controllers
11070	out 0x0d,al
11071	out 0xda,al
11072
11073	;; then initialize the DMA controllers
11074	mov al, #0xC0
11075	out 0xD6, al ; cascade mode of channel 4 enabled
11076	mov al, #0x00
11077	out 0xD4, al ; unmask channel 4
11078
11079	;; Examine CMOS shutdown status.
11080	mov AL, #0x0f
11081	out 0x70, AL
11082	in AL, 0x71
11083
11084	;; backup status
11085	mov bl, al
11086
11087	;; Reset CMOS shutdown status.
11088	mov AL, #0x0f
11089	out 0x70, AL ; select CMOS register Fh
11090	mov AL, #0x00
11091	out 0x71, AL ; set shutdown action to normal
11092
11093	;; Examine CMOS shutdown status.
11094	mov al, bl
11095
11096	;; 0x00, 0x09, 0x0D+ = normal startup
11097	cmp AL, #0x00
11098	jz normal_post
11099	cmp AL, #0x0d
11100	jae normal_post
11101	cmp AL, #0x09
11102	je normal_post
11103
11104	;; 0x05 = eoi + jmp via [0x40:0x67] jump
11105	cmp al, #0x05
11106	je eoi_jmp_post
11107
11108	;; Examine CMOS shutdown status.
11109	;; 0x01,0x02,0x03,0x04,0x06,0x07,0x08, 0x0a, 0x0b, 0x0c = Unimplemented shutdown status.
11110	push bx
11111	call _shutdown_status_panic
11112
11113	#if 0
11114	HALT(__LINE__)
11115	;
11116	;#if 0
11117	; 0xb0, 0x20, /* mov al, #0x20 */
11118	; 0xe6, 0x20, /* out 0x20, al ;send EOI to PIC */
11119	;#endif
11120	;
11121	pop es
11122	pop ds
11123	popa
11124	iret
11125	#endif
11126
11127	normal_post:
11128	; case 0: normal startup
11129
11130	cli
11131	mov ax, #0xfffe
11132	mov sp, ax
11133	xor ax, ax
11134	mov ds, ax
11135	mov ss, ax
11136
11137	#ifndef VBOX
11138	;; zero out BIOS data area (40:00..40:ff)
11139	mov es, ax
11140	mov cx, #0x0080 ;; 128 words
11141	mov di, #0x0400
11142	cld
11143	rep
11144	stosw
11145	#else /* VBOX */
11146	;; zero out segment 0 (includes BIOS data area) except word at 40:72
11147	mov es, ax
11148	xor di, di
11149	cld
11150	mov cx, #0x0239 ;; 569 words
11151	rep
11152	stosw
11153	inc di
11154	inc di
11155	mov cx, #0x7dc6 ;; 32198 words
11156	rep
11157	stosw
11158	;; zero out remaining base memory except the last 16 bytes of the EBDA
11159	;; because we store the MP table there
11160	xor eax, eax
11161	xor bx, bx
11162	memory_zero_loop:
11163	add bx, #0x1000
11164	cmp bx, #0x9000
11165	jae memory_cleared
11166	mov es, bx
11167	xor di, di
11168	mov cx, #0x4000
11169	rep
11170	stosd
11171	jmp memory_zero_loop
11172	memory_cleared:
11173	mov es, bx
11174	xor di, di
11175	mov cx, #0x3f00
11176	rep
11177	stosd
11178	xor bx, bx
11179	#endif
11180
11181	call _log_bios_start
11182
11183	;; set all interrupts to default handler
11184	xor bx, bx ;; offset index
11185	mov cx, #0x0100 ;; counter (256 interrupts)
11186	mov ax, #dummy_iret_handler
11187	mov dx, #0xF000
11188
11189	post_default_ints:
11190	mov [bx], ax
11191	inc bx
11192	inc bx
11193	mov [bx], dx
11194	inc bx
11195	inc bx
11196	loop post_default_ints
11197
11198	;; set vector 0x79 to zero
11199	;; this is used by 'gardian angel' protection system
11200	SET_INT_VECTOR(0x79, #0, #0)
11201
11202	;; base memory in K 40:13 (word)
11203	mov ax, #BASE_MEM_IN_K
11204	mov 0x0413, ax
11205
11206
11207	;; Manufacturing Test 40:12
11208	;; zerod out above
11209
11210	#ifndef VBOX
11211	;; Warm Boot Flag 0040:0072
11212	;; value of 1234h = skip memory checks
11213	;; zerod out above
11214	#endif /* !VBOX */
11215
11216
11217	;; Printer Services vector
11218	SET_INT_VECTOR(0x17, #0xF000, #int17_handler)
11219
11220	;; Bootstrap failure vector
11221	SET_INT_VECTOR(0x18, #0xF000, #int18_handler)
11222
11223	;; Bootstrap Loader vector
11224	SET_INT_VECTOR(0x19, #0xF000, #int19_handler)
11225
11226	;; User Timer Tick vector
11227	SET_INT_VECTOR(0x1c, #0xF000, #int1c_handler)
11228
11229	;; Memory Size Check vector
11230	SET_INT_VECTOR(0x12, #0xF000, #int12_handler)
11231
11232	;; Equipment Configuration Check vector
11233	SET_INT_VECTOR(0x11, #0xF000, #int11_handler)
11234
11235	;; System Services
11236	SET_INT_VECTOR(0x15, #0xF000, #int15_handler)
11237
11238	;; EBDA setup
11239	call ebda_post
11240
11241	;; PIT setup
11242	SET_INT_VECTOR(0x08, #0xF000, #int08_handler)
11243	;; int 1C already points at dummy_iret_handler (above)
11244	mov al, #0x34 ; timer0: binary count, 16bit count, mode 2
11245	out 0x43, al
11246	mov al, #0x00 ; maximum count of 0000H = 18.2Hz
11247	out 0x40, al
11248	out 0x40, al
11249
11250	;; Keyboard
11251	SET_INT_VECTOR(0x09, #0xF000, #int09_handler)
11252	SET_INT_VECTOR(0x16, #0xF000, #int16_handler)
11253
11254	xor ax, ax
11255	mov ds, ax
11256	mov 0x0417, al /* keyboard shift flags, set 1 */
11257	mov 0x0418, al /* keyboard shift flags, set 2 */
11258	mov 0x0419, al /* keyboard alt-numpad work area */
11259	mov 0x0471, al /* keyboard ctrl-break flag */
11260	mov 0x0497, al /* keyboard status flags 4 */
11261	mov al, #0x10
11262	mov 0x0496, al /* keyboard status flags 3 */
11263
11264
11265	/* keyboard head of buffer pointer */
11266	mov bx, #0x001E
11267	mov 0x041A, bx
11268
11269	/* keyboard end of buffer pointer */
11270	mov 0x041C, bx
11271
11272	/* keyboard pointer to start of buffer */
11273	mov bx, #0x001E
11274	mov 0x0480, bx
11275
11276	/* keyboard pointer to end of buffer */
11277	mov bx, #0x003E
11278	mov 0x0482, bx
11279
11280	/* init the keyboard */
11281	call _keyboard_init
11282
11283	;; mov CMOS Equipment Byte to BDA Equipment Word
11284	mov ax, 0x0410
11285	mov al, #0x14
11286	out 0x70, al
11287	in al, 0x71
11288	mov 0x0410, ax
11289
11290
11291	;; Parallel setup
11292	SET_INT_VECTOR(0x0F, #0xF000, #dummy_iret_handler)
11293	xor ax, ax
11294	mov ds, ax
11295	xor bx, bx
11296	mov cl, #0x14 ; timeout value
11297	mov dx, #0x378 ; Parallel I/O address, port 1
11298	call detect_parport
11299	mov dx, #0x278 ; Parallel I/O address, port 2
11300	call detect_parport
11301	shl bx, #0x0e
11302	mov ax, 0x410 ; Equipment word bits 14..15 determing # parallel ports
11303	and ax, #0x3fff
11304	or ax, bx ; set number of parallel ports
11305	mov 0x410, ax
11306
11307	;; Serial setup
11308	SET_INT_VECTOR(0x0C, #0xF000, #dummy_iret_handler)
11309	SET_INT_VECTOR(0x14, #0xF000, #int14_handler)
11310	xor bx, bx
11311	mov cl, #0x0a ; timeout value
11312	mov dx, #0x03f8 ; Serial I/O address, port 1
11313	call detect_serial
11314	mov dx, #0x02f8 ; Serial I/O address, port 2
11315	call detect_serial
11316	mov dx, #0x03e8 ; Serial I/O address, port 3
11317	call detect_serial
11318	mov dx, #0x02e8 ; Serial I/O address, port 4
11319	call detect_serial
11320	shl bx, #0x09
11321	mov ax, 0x410 ; Equipment word bits 9..11 determing # serial ports
11322	and ax, #0xf1ff
11323	or ax, bx ; set number of serial port
11324	mov 0x410, ax
11325
11326	;; CMOS RTC
11327	SET_INT_VECTOR(0x1A, #0xF000, #int1a_handler)
11328	SET_INT_VECTOR(0x4A, #0xF000, #dummy_iret_handler)
11329	SET_INT_VECTOR(0x70, #0xF000, #int70_handler)
11330	;; BIOS DATA AREA 0x4CE ???
11331	call timer_tick_post
11332
11333	;; PS/2 mouse setup
11334	SET_INT_VECTOR(0x74, #0xF000, #int74_handler)
11335
11336	;; IRQ13 (FPU exception) setup
11337	SET_INT_VECTOR(0x75, #0xF000, #int75_handler)
11338
11339	;; Video setup
11340	SET_INT_VECTOR(0x10, #0xF000, #int10_handler)
11341
11342	#ifdef VBOX
11343	;; moved the PIC initialization to another place as we need
11344	;; some space for additions init calls. Otherwise this code
11345	;; overlaps with the NMI handler at 0xe2c3 (fixed BIOS entry)
11346	call init_pic
11347	#else /* !VBOX */
11348	;; PIC
11349	mov al, #0x11 ; send initialisation commands
11350	out 0x20, al
11351	out 0xa0, al
11352	mov al, #0x08
11353	out 0x21, al
11354	mov al, #0x70
11355	out 0xa1, al
11356	mov al, #0x04
11357	out 0x21, al
11358	mov al, #0x02
11359	out 0xa1, al
11360	mov al, #0x01
11361	out 0x21, al
11362	out 0xa1, al
11363	mov al, #0xb8
11364	out 0x21, AL ;master pic: unmask IRQ 0, 1, 2, 6
11365	#if BX_USE_PS2_MOUSE
11366	mov al, #0x8f
11367	#else
11368	mov al, #0x9f
11369	#endif
11370	out 0xa1, AL ;slave pic: unmask IRQ 12, 13, 14
11371	#endif /* !VBOX */
11372
11373	#if BX_ROMBIOS32
11374	call rombios32_init
11375	#else
11376	call pcibios_init_iomem_bases
11377	call pcibios_init_irqs
11378	#endif
11379	call rom_scan
11380
11381	#if BX_USE_ATADRV
11382	;;
11383	;; ATA/ATAPI driver setup
11384	;;
11385	call _ata_init
11386	call _ata_detect
11387	;;
11388	#endif
11389
11390	#ifdef VBOX_WITH_SCSI
11391	;;
11392	;; SCSI driver setup
11393	;;
11394	call _scsi_init
11395	;;
11396	#endif
11397
11398	call _print_bios_banner
11399
11400	;;
11401	;; Floppy setup
11402	;;
11403	call floppy_drive_post
11404
11405	;;
11406	;; Hard Drive setup
11407	;;
11408	call hard_drive_post
11409
11410	#if BX_ELTORITO_BOOT
11411	;;
11412	;; eltorito floppy/harddisk emulation from cd
11413	;;
11414	call _cdemu_init
11415	;;
11416	#endif // BX_ELTORITO_BOOT
11417
11418	sti ;; enable interrupts
11419	int #0x19
11420
11421
11422	.org 0xe2c3 ; NMI Handler Entry Point
11423	nmi:
11424	;; FIXME the NMI handler should not panic
11425	;; but iret when called from int75 (fpu exception)
11426	call _nmi_handler_msg
11427	iret
11428
11429	int75_handler:
11430	out 0xf0, al // clear irq13
11431	call eoi_both_pics // clear interrupt
11432	int 2 // legacy nmi call
11433	iret
11434
11435	;-------------------------------------------
11436	;- INT 13h Fixed Disk Services Entry Point -
11437	;-------------------------------------------
11438	.org 0xe3fe ; INT 13h Fixed Disk Services Entry Point
11439	int13_handler:
11440	//JMPL(int13_relocated)
11441	jmp int13_relocated
11442
11443	.org 0xe401 ; Fixed Disk Parameter Table
11444
11445	;----------
11446	;- INT19h -
11447	;----------
11448	.org 0xe6f2 ; INT 19h Boot Load Service Entry Point
11449	int19_handler:
11450
11451	jmp int19_relocated
11452	;-------------------------------------------
11453	;- System BIOS Configuration Data Table
11454	;-------------------------------------------
11455	.org BIOS_CONFIG_TABLE
11456	db 0x08 ; Table size (bytes) -Lo
11457	db 0x00 ; Table size (bytes) -Hi
11458	db SYS_MODEL_ID
11459	db SYS_SUBMODEL_ID
11460	db BIOS_REVISION
11461	; Feature byte 1
11462	; b7: 1=DMA channel 3 used by hard disk
11463	; b6: 1=2 interrupt controllers present
11464	; b5: 1=RTC present
11465	; b4: 1=BIOS calls int 15h/4Fh every key
11466	; b3: 1=wait for extern event supported (Int 15h/41h)
11467	; b2: 1=extended BIOS data area used
11468	; b1: 0=AT or ESDI bus, 1=MicroChannel
11469	; b0: 1=Dual bus (MicroChannel + ISA)
11470	db (0 << 7) \| \
11471	(1 << 6) \| \
11472	(1 << 5) \| \
11473	(BX_CALL_INT15_4F << 4) \| \
11474	(0 << 3) \| \
11475	(BX_USE_EBDA << 2) \| \
11476	(0 << 1) \| \
11477	(0 << 0)
11478	; Feature byte 2
11479	; b7: 1=32-bit DMA supported
11480	; b6: 1=int16h, function 9 supported
11481	; b5: 1=int15h/C6h (get POS data) supported
11482	; b4: 1=int15h/C7h (get mem map info) supported
11483	; b3: 1=int15h/C8h (en/dis CPU) supported
11484	; b2: 1=non-8042 kb controller
11485	; b1: 1=data streaming supported
11486	; b0: reserved
11487	db (0 << 7) \| \
11488	(1 << 6) \| \
11489	(0 << 5) \| \
11490	(0 << 4) \| \
11491	(0 << 3) \| \
11492	(0 << 2) \| \
11493	(0 << 1) \| \
11494	(0 << 0)
11495	; Feature byte 3
11496	; b7: not used
11497	; b6: reserved
11498	; b5: reserved
11499	; b4: POST supports ROM-to-RAM enable/disable
11500	; b3: SCSI on system board
11501	; b2: info panel installed
11502	; b1: Initial Machine Load (IML) system - BIOS on disk
11503	; b0: SCSI supported in IML
11504	db 0x00
11505	; Feature byte 4
11506	; b7: IBM private
11507	; b6: EEPROM present
11508	; b5-3: ABIOS presence (011 = not supported)
11509	; b2: private
11510	; b1: memory split above 16Mb supported
11511	; b0: POSTEXT directly supported by POST
11512	db 0x00
11513	; Feature byte 5 (IBM)
11514	; b1: enhanced mouse
11515	; b0: flash EPROM
11516	db 0x00
11517
11518
11519
11520	.org 0xe729 ; Baud Rate Generator Table
11521
11522	;----------
11523	;- INT14h -
11524	;----------
11525	.org 0xe739 ; INT 14h Serial Communications Service Entry Point
11526	int14_handler:
11527	push ds
11528	pusha
11529	xor ax, ax
11530	mov ds, ax
11531	call _int14_function
11532	popa
11533	pop ds
11534	iret
11535
11536
11537	;----------------------------------------
11538	;- INT 16h Keyboard Service Entry Point -
11539	;----------------------------------------
11540	.org 0xe82e
11541	int16_handler:
11542
11543	sti
11544	push ds
11545	pushf
11546	pusha
11547
11548	cmp ah, #0x00
11549	je int16_F00
11550	cmp ah, #0x10
11551	je int16_F00
11552
11553	mov bx, #0xf000
11554	mov ds, bx
11555	call _int16_function
11556	popa
11557	popf
11558	pop ds
11559	jz int16_zero_set
11560
11561	int16_zero_clear:
11562	push bp
11563	mov bp, sp
11564	//SEG SS
11565	and BYTE [bp + 0x06], #0xbf
11566	pop bp
11567	iret
11568
11569	int16_zero_set:
11570	push bp
11571	mov bp, sp
11572	//SEG SS
11573	or BYTE [bp + 0x06], #0x40
11574	pop bp
11575	iret
11576
11577	int16_F00:
11578	mov bx, #0x0040
11579	mov ds, bx
11580
11581	int16_wait_for_key:
11582	cli
11583	mov bx, 0x001a
11584	cmp bx, 0x001c
11585	jne int16_key_found
11586	sti
11587	nop
11588	#if 0
11589	/* no key yet, call int 15h, function AX=9002 */
11590	0x50, /* push AX */
11591	0xb8, 0x02, 0x90, /* mov AX, #0x9002 */
11592	0xcd, 0x15, /* int 15h */
11593	0x58, /* pop AX */
11594	0xeb, 0xea, /* jmp WAIT_FOR_KEY */
11595	#endif
11596	jmp int16_wait_for_key
11597
11598	int16_key_found:
11599	mov bx, #0xf000
11600	mov ds, bx
11601	call _int16_function
11602	popa
11603	popf
11604	pop ds
11605	#if 0
11606	/* notify int16 complete w/ int 15h, function AX=9102 */
11607	0x50, /* push AX */
11608	0xb8, 0x02, 0x91, /* mov AX, #0x9102 */
11609	0xcd, 0x15, /* int 15h */
11610	0x58, /* pop AX */
11611	#endif
11612	iret
11613
11614
11615
11616	;-------------------------------------------------
11617	;- INT09h : Keyboard Hardware Service Entry Point -
11618	;-------------------------------------------------
11619	.org 0xe987
11620	int09_handler:
11621	cli
11622	push ax
11623
11624	mov al, #0xAD ;;disable keyboard
11625	out #0x64, al
11626
11627	mov al, #0x0B
11628	out #0x20, al
11629	in al, #0x20
11630	and al, #0x02
11631	jz int09_finish
11632
11633	in al, #0x60 ;;read key from keyboard controller
11634	sti
11635	push ds
11636	pusha
11637	#ifdef BX_CALL_INT15_4F
11638	mov ah, #0x4f ;; allow for keyboard intercept
11639	stc
11640	int #0x15
11641	jnc int09_done
11642	#endif
11643
11644	;; check for extended key
11645	cmp al, #0xe0
11646	jne int09_check_pause
11647	xor ax, ax
11648	mov ds, ax
11649	mov al, BYTE [0x496] ;; mf2_state \|= 0x02
11650	or al, #0x02
11651	mov BYTE [0x496], al
11652	jmp int09_done
11653
11654	int09_check_pause: ;; check for pause key
11655	cmp al, #0xe1
11656	jne int09_process_key
11657	xor ax, ax
11658	mov ds, ax
11659	mov al, BYTE [0x496] ;; mf2_state \|= 0x01
11660	or al, #0x01
11661	mov BYTE [0x496], al
11662	jmp int09_done
11663
11664	int09_process_key:
11665	mov bx, #0xf000
11666	mov ds, bx
11667	call _int09_function
11668
11669	int09_done:
11670	popa
11671	pop ds
11672	cli
11673	call eoi_master_pic
11674
11675	int09_finish:
11676	mov al, #0xAE ;;enable keyboard
11677	out #0x64, al
11678	pop ax
11679	iret
11680
11681
11682	;----------------------------------------
11683	;- INT 13h Diskette Service Entry Point -
11684	;----------------------------------------
11685	.org 0xec59
11686	int13_diskette:
11687	jmp int13_noeltorito
11688
11689	;---------------------------------------------
11690	;- INT 0Eh Diskette Hardware ISR Entry Point -
11691	;---------------------------------------------
11692	.org 0xef57 ; INT 0Eh Diskette Hardware ISR Entry Point
11693	int0e_handler:
11694	push ax
11695	push dx
11696	mov dx, #0x03f4
11697	in al, dx
11698	and al, #0xc0
11699	cmp al, #0xc0
11700	je int0e_normal
11701	mov dx, #0x03f5
11702	mov al, #0x08 ; sense interrupt status
11703	out dx, al
11704	int0e_loop1:
11705	mov dx, #0x03f4
11706	in al, dx
11707	and al, #0xc0
11708	cmp al, #0xc0
11709	jne int0e_loop1
11710	int0e_loop2:
11711	mov dx, #0x03f5
11712	in al, dx
11713	mov dx, #0x03f4
11714	in al, dx
11715	and al, #0xc0
11716	cmp al, #0xc0
11717	je int0e_loop2
11718	int0e_normal:
11719	push ds
11720	xor ax, ax ;; segment 0000
11721	mov ds, ax
11722	call eoi_master_pic
11723	mov al, 0x043e
11724	or al, #0x80 ;; diskette interrupt has occurred
11725	mov 0x043e, al
11726	pop ds
11727	pop dx
11728	pop ax
11729	iret
11730
11731
11732	.org 0xefc7 ; Diskette Controller Parameter Table
11733	diskette_param_table:
11734	;; Since no provisions are made for multiple drive types, most
11735	;; values in this table are ignored. I set parameters for 1.44M
11736	;; floppy here
11737	db 0xAF
11738	db 0x02 ;; head load time 0000001, DMA used
11739	db 0x25
11740	db 0x02
11741	db 18
11742	db 0x1B
11743	db 0xFF
11744	db 0x6C
11745	db 0xF6
11746	db 0x0F
11747	db 0x08
11748
11749
11750	;----------------------------------------
11751	;- INT17h : Printer Service Entry Point -
11752	;----------------------------------------
11753	.org 0xefd2
11754	int17_handler:
11755	push ds
11756	pusha
11757	xor ax, ax
11758	mov ds, ax
11759	call _int17_function
11760	popa
11761	pop ds
11762	iret
11763
11764	diskette_param_table2:
11765	;; New diskette parameter table adding 3 parameters from IBM
11766	;; Since no provisions are made for multiple drive types, most
11767	;; values in this table are ignored. I set parameters for 1.44M
11768	;; floppy here
11769	db 0xAF
11770	db 0x02 ;; head load time 0000001, DMA used
11771	db 0x25
11772	db 0x02
11773	db 18
11774	db 0x1B
11775	db 0xFF
11776	db 0x6C
11777	db 0xF6
11778	db 0x0F
11779	db 0x08
11780	db 79 ;; maximum track
11781	db 0 ;; data transfer rate
11782	db 4 ;; drive type in cmos
11783
11784	.org 0xf045 ; INT 10 Functions 0-Fh Entry Point
11785	HALT(__LINE__)
11786	iret
11787
11788	;----------
11789	;- INT10h -
11790	;----------
11791	.org 0xf065 ; INT 10h Video Support Service Entry Point
11792	int10_handler:
11793	;; dont do anything, since the VGA BIOS handles int10h requests
11794	iret
11795
11796	.org 0xf0a4 ; MDA/CGA Video Parameter Table (INT 1Dh)
11797
11798	;----------
11799	;- INT12h -
11800	;----------
11801	.org 0xf841 ; INT 12h Memory Size Service Entry Point
11802	; ??? different for Pentium (machine check)?
11803	int12_handler:
11804	push ds
11805	mov ax, #0x0040
11806	mov ds, ax
11807	mov ax, 0x0013
11808	pop ds
11809	iret
11810
11811	;----------
11812	;- INT11h -
11813	;----------
11814	.org 0xf84d ; INT 11h Equipment List Service Entry Point
11815	int11_handler:
11816	push ds
11817	mov ax, #0x0040
11818	mov ds, ax
11819	mov ax, 0x0010
11820	pop ds
11821	iret
11822
11823	;----------
11824	;- INT15h -
11825	;----------
11826	.org 0xf859 ; INT 15h System Services Entry Point
11827	int15_handler:
11828	pushf
11829	#if BX_APM
11830	cmp ah, #0x53
11831	je apm_call
11832	#endif
11833	push ds
11834	push es
11835	cmp ah, #0x86
11836	je int15_handler32
11837	cmp ah, #0xE8
11838	je int15_handler32
11839	pusha
11840	#if BX_USE_PS2_MOUSE
11841	cmp ah, #0xC2
11842	je int15_handler_mouse
11843	#endif
11844	call _int15_function
11845	int15_handler_mouse_ret:
11846	popa
11847	int15_handler32_ret:
11848	pop es
11849	pop ds
11850	popf
11851	jmp iret_modify_cf
11852	#if BX_APM
11853	apm_call:
11854	jmp _apmreal_entry
11855	#endif
11856
11857	#if BX_USE_PS2_MOUSE
11858	int15_handler_mouse:
11859	call _int15_function_mouse
11860	jmp int15_handler_mouse_ret
11861	#endif
11862
11863	int15_handler32:
11864	pushad
11865	call _int15_function32
11866	popad
11867	jmp int15_handler32_ret
11868
11869	;; Protected mode IDT descriptor
11870	;;
11871	;; I just make the limit 0, so the machine will shutdown
11872	;; if an exception occurs during protected mode memory
11873	;; transfers.
11874	;;
11875	;; Set base to f0000 to correspond to beginning of BIOS,
11876	;; in case I actually define an IDT later
11877	;; Set limit to 0
11878
11879	pmode_IDT_info:
11880	dw 0x0000 ;; limit 15:00
11881	dw 0x0000 ;; base 15:00
11882	db 0x0f ;; base 23:16
11883
11884	;; Real mode IDT descriptor
11885	;;
11886	;; Set to typical real-mode values.
11887	;; base = 000000
11888	;; limit = 03ff
11889
11890	rmode_IDT_info:
11891	dw 0x03ff ;; limit 15:00
11892	dw 0x0000 ;; base 15:00
11893	db 0x00 ;; base 23:16
11894
11895	;;
11896	;; Handler for unexpected hardware interrupts
11897	;;
11898	dummy_isr:
11899	push ds
11900	pushad
11901	xor ax, ax
11902	mov ds, ax
11903	call _dummy_isr_function
11904	popad
11905	pop ds
11906	iret
11907
11908	;----------
11909	;- INT1Ah -
11910	;----------
11911	.org 0xfe6e ; INT 1Ah Time-of-day Service Entry Point
11912	int1a_handler:
11913	#if BX_PCIBIOS
11914	cmp ah, #0xb1
11915	jne int1a_normal
11916	call pcibios_real
11917	jc pcibios_error
11918	retf 2
11919	pcibios_error:
11920	mov bl, ah
11921	mov ah, #0xb1
11922	push ds
11923	pusha
11924	mov ax, ss ; set readable descriptor to ds, for calling pcibios
11925	mov ds, ax ; on 16bit protected mode.
11926	jmp int1a_callfunction
11927	int1a_normal:
11928	#endif
11929	push ds
11930	pusha
11931	xor ax, ax
11932	mov ds, ax
11933	int1a_callfunction:
11934	call _int1a_function
11935	popa
11936	pop ds
11937	iret
11938
11939	;;
11940	;; int70h: IRQ8 - CMOS RTC
11941	;;
11942	int70_handler:
11943	push ds
11944	pushad
11945	xor ax, ax
11946	mov ds, ax
11947	call _int70_function
11948	popad
11949	pop ds
11950	iret
11951
11952	;---------
11953	;- INT08 -
11954	;---------
11955	.org 0xfea5 ; INT 08h System Timer ISR Entry Point
11956	int08_handler:
11957	sti
11958	push eax
11959	push ds
11960	xor ax, ax
11961	mov ds, ax
11962
11963	;; time to turn off drive(s)?
11964	mov al,0x0440
11965	or al,al
11966	jz int08_floppy_off
11967	dec al
11968	mov 0x0440,al
11969	jnz int08_floppy_off
11970	;; turn motor(s) off
11971	push dx
11972	mov dx,#0x03f2
11973	in al,dx
11974	and al,#0xcf
11975	out dx,al
11976	pop dx
11977	int08_floppy_off:
11978
11979	mov eax, 0x046c ;; get ticks dword
11980	inc eax
11981
11982	;; compare eax to one days worth of timer ticks at 18.2 hz
11983	cmp eax, #0x001800B0
11984	jb int08_store_ticks
11985	;; there has been a midnight rollover at this point
11986	xor eax, eax ;; zero out counter
11987	inc BYTE 0x0470 ;; increment rollover flag
11988
11989	int08_store_ticks:
11990	mov 0x046c, eax ;; store new ticks dword
11991	;; chain to user timer tick INT #0x1c
11992	//pushf
11993	//;; call_ep [ds:loc]
11994	//CALL_EP( 0x1c << 2 )
11995	int #0x1c
11996	cli
11997	call eoi_master_pic
11998	pop ds
11999	pop eax
12000	iret
12001
12002	.org 0xfef3 ; Initial Interrupt Vector Offsets Loaded by POST
12003
12004
12005	.org 0xff00
12006	.ascii BIOS_COPYRIGHT_STRING
12007
12008	#ifdef VBOX
12009	// The SMBIOS header
12010	.org 0xff30
12011	.align 16
12012	db 0x5f, 0x53, 0x4d, 0x5f ; "_SM_" signature
12013	db 0x00 ; checksum (set by biossums)
12014	db 0x1f ; EPS length, defined by standard
12015	db VBOX_SMBIOS_MAJOR_VER ; SMBIOS major version
12016	db VBOX_SMBIOS_MINOR_VER ; SMBIOS minor version
12017	dw VBOX_SMBIOS_MAXSS ; Maximum structure size
12018	db 0x00 ; Entry point revision
12019	db 0x00, 0x00, 0x00, 0x00, 0x00
12020
12021	// The DMI header
12022	db 0x5f, 0x44, 0x4d, 0x49, 0x5f ; "_DMI_" signature
12023	db 0x00 ; checksum (set by biossums)
12024	dw VBOX_DMI_TABLE_SIZE ; DMI tables length
12025	dd VBOX_DMI_TABLE_BASE ; DMI tables base
12026	dw VBOX_DMI_TABLE_ENTR ; DMI tables entries
12027	db VBOX_DMI_TABLE_VER ; DMI version
12028	db 0x00 ; Just for alignment
12029	#endif
12030
12031	;------------------------------------------------
12032	;- IRET Instruction for Dummy Interrupt Handler -
12033	;------------------------------------------------
12034	.org 0xff53 ; IRET Instruction for Dummy Interrupt Handler
12035	dummy_iret_handler:
12036	iret
12037
12038	.org 0xff54 ; INT 05h Print Screen Service Entry Point
12039	HALT(__LINE__)
12040	iret
12041
12042	.org 0xfff0 ; Power-up Entry Point
12043	jmp 0xf000:post
12044
12045	.org 0xfff5 ; ASCII Date ROM was built - 8 characters in MM/DD/YY
12046	.ascii BIOS_BUILD_DATE
12047
12048	.org 0xfffe ; System Model ID
12049	db SYS_MODEL_ID
12050	db 0x00 ; filler
12051
12052	.org 0xfa6e ;; Character Font for 320x200 & 640x200 Graphics (lower 128 characters)
12053	ASM_END
12054	/*
12055	* This font comes from the fntcol16.zip package (c) by Joseph Gil
12056	* found at ftp://ftp.simtel.net/pub/simtelnet/msdos/screen/fntcol16.zip
12057	* This font is public domain
12058	*/
12059	static Bit8u vgafont8[128*8]=
12060	{
12061	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
12062	0x7e, 0x81, 0xa5, 0x81, 0xbd, 0x99, 0x81, 0x7e,
12063	0x7e, 0xff, 0xdb, 0xff, 0xc3, 0xe7, 0xff, 0x7e,
12064	0x6c, 0xfe, 0xfe, 0xfe, 0x7c, 0x38, 0x10, 0x00,
12065	0x10, 0x38, 0x7c, 0xfe, 0x7c, 0x38, 0x10, 0x00,
12066	0x38, 0x7c, 0x38, 0xfe, 0xfe, 0x7c, 0x38, 0x7c,
12067	0x10, 0x10, 0x38, 0x7c, 0xfe, 0x7c, 0x38, 0x7c,
12068	0x00, 0x00, 0x18, 0x3c, 0x3c, 0x18, 0x00, 0x00,
12069	0xff, 0xff, 0xe7, 0xc3, 0xc3, 0xe7, 0xff, 0xff,
12070	0x00, 0x3c, 0x66, 0x42, 0x42, 0x66, 0x3c, 0x00,
12071	0xff, 0xc3, 0x99, 0xbd, 0xbd, 0x99, 0xc3, 0xff,
12072	0x0f, 0x07, 0x0f, 0x7d, 0xcc, 0xcc, 0xcc, 0x78,
12073	0x3c, 0x66, 0x66, 0x66, 0x3c, 0x18, 0x7e, 0x18,
12074	0x3f, 0x33, 0x3f, 0x30, 0x30, 0x70, 0xf0, 0xe0,
12075	0x7f, 0x63, 0x7f, 0x63, 0x63, 0x67, 0xe6, 0xc0,
12076	0x99, 0x5a, 0x3c, 0xe7, 0xe7, 0x3c, 0x5a, 0x99,
12077	0x80, 0xe0, 0xf8, 0xfe, 0xf8, 0xe0, 0x80, 0x00,
12078	0x02, 0x0e, 0x3e, 0xfe, 0x3e, 0x0e, 0x02, 0x00,
12079	0x18, 0x3c, 0x7e, 0x18, 0x18, 0x7e, 0x3c, 0x18,
12080	0x66, 0x66, 0x66, 0x66, 0x66, 0x00, 0x66, 0x00,
12081	0x7f, 0xdb, 0xdb, 0x7b, 0x1b, 0x1b, 0x1b, 0x00,
12082	0x3e, 0x63, 0x38, 0x6c, 0x6c, 0x38, 0xcc, 0x78,
12083	0x00, 0x00, 0x00, 0x00, 0x7e, 0x7e, 0x7e, 0x00,
12084	0x18, 0x3c, 0x7e, 0x18, 0x7e, 0x3c, 0x18, 0xff,
12085	0x18, 0x3c, 0x7e, 0x18, 0x18, 0x18, 0x18, 0x00,
12086	0x18, 0x18, 0x18, 0x18, 0x7e, 0x3c, 0x18, 0x00,
12087	0x00, 0x18, 0x0c, 0xfe, 0x0c, 0x18, 0x00, 0x00,
12088	0x00, 0x30, 0x60, 0xfe, 0x60, 0x30, 0x00, 0x00,
12089	0x00, 0x00, 0xc0, 0xc0, 0xc0, 0xfe, 0x00, 0x00,
12090	0x00, 0x24, 0x66, 0xff, 0x66, 0x24, 0x00, 0x00,
12091	0x00, 0x18, 0x3c, 0x7e, 0xff, 0xff, 0x00, 0x00,
12092	0x00, 0xff, 0xff, 0x7e, 0x3c, 0x18, 0x00, 0x00,
12093	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
12094	0x30, 0x78, 0x78, 0x30, 0x30, 0x00, 0x30, 0x00,
12095	0x6c, 0x6c, 0x6c, 0x00, 0x00, 0x00, 0x00, 0x00,
12096	0x6c, 0x6c, 0xfe, 0x6c, 0xfe, 0x6c, 0x6c, 0x00,
12097	0x30, 0x7c, 0xc0, 0x78, 0x0c, 0xf8, 0x30, 0x00,
12098	0x00, 0xc6, 0xcc, 0x18, 0x30, 0x66, 0xc6, 0x00,
12099	0x38, 0x6c, 0x38, 0x76, 0xdc, 0xcc, 0x76, 0x00,
12100	0x60, 0x60, 0xc0, 0x00, 0x00, 0x00, 0x00, 0x00,
12101	0x18, 0x30, 0x60, 0x60, 0x60, 0x30, 0x18, 0x00,
12102	0x60, 0x30, 0x18, 0x18, 0x18, 0x30, 0x60, 0x00,
12103	0x00, 0x66, 0x3c, 0xff, 0x3c, 0x66, 0x00, 0x00,
12104	0x00, 0x30, 0x30, 0xfc, 0x30, 0x30, 0x00, 0x00,
12105	0x00, 0x00, 0x00, 0x00, 0x00, 0x30, 0x30, 0x60,
12106	0x00, 0x00, 0x00, 0xfc, 0x00, 0x00, 0x00, 0x00,
12107	0x00, 0x00, 0x00, 0x00, 0x00, 0x30, 0x30, 0x00,
12108	0x06, 0x0c, 0x18, 0x30, 0x60, 0xc0, 0x80, 0x00,
12109	0x7c, 0xc6, 0xce, 0xde, 0xf6, 0xe6, 0x7c, 0x00,
12110	0x30, 0x70, 0x30, 0x30, 0x30, 0x30, 0xfc, 0x00,
12111	0x78, 0xcc, 0x0c, 0x38, 0x60, 0xcc, 0xfc, 0x00,
12112	0x78, 0xcc, 0x0c, 0x38, 0x0c, 0xcc, 0x78, 0x00,
12113	0x1c, 0x3c, 0x6c, 0xcc, 0xfe, 0x0c, 0x1e, 0x00,
12114	0xfc, 0xc0, 0xf8, 0x0c, 0x0c, 0xcc, 0x78, 0x00,
12115	0x38, 0x60, 0xc0, 0xf8, 0xcc, 0xcc, 0x78, 0x00,
12116	0xfc, 0xcc, 0x0c, 0x18, 0x30, 0x30, 0x30, 0x00,
12117	0x78, 0xcc, 0xcc, 0x78, 0xcc, 0xcc, 0x78, 0x00,
12118	0x78, 0xcc, 0xcc, 0x7c, 0x0c, 0x18, 0x70, 0x00,
12119	0x00, 0x30, 0x30, 0x00, 0x00, 0x30, 0x30, 0x00,
12120	0x00, 0x30, 0x30, 0x00, 0x00, 0x30, 0x30, 0x60,
12121	0x18, 0x30, 0x60, 0xc0, 0x60, 0x30, 0x18, 0x00,
12122	0x00, 0x00, 0xfc, 0x00, 0x00, 0xfc, 0x00, 0x00,
12123	0x60, 0x30, 0x18, 0x0c, 0x18, 0x30, 0x60, 0x00,
12124	0x78, 0xcc, 0x0c, 0x18, 0x30, 0x00, 0x30, 0x00,
12125	0x7c, 0xc6, 0xde, 0xde, 0xde, 0xc0, 0x78, 0x00,
12126	0x30, 0x78, 0xcc, 0xcc, 0xfc, 0xcc, 0xcc, 0x00,
12127	0xfc, 0x66, 0x66, 0x7c, 0x66, 0x66, 0xfc, 0x00,
12128	0x3c, 0x66, 0xc0, 0xc0, 0xc0, 0x66, 0x3c, 0x00,
12129	0xf8, 0x6c, 0x66, 0x66, 0x66, 0x6c, 0xf8, 0x00,
12130	0xfe, 0x62, 0x68, 0x78, 0x68, 0x62, 0xfe, 0x00,
12131	0xfe, 0x62, 0x68, 0x78, 0x68, 0x60, 0xf0, 0x00,
12132	0x3c, 0x66, 0xc0, 0xc0, 0xce, 0x66, 0x3e, 0x00,
12133	0xcc, 0xcc, 0xcc, 0xfc, 0xcc, 0xcc, 0xcc, 0x00,
12134	0x78, 0x30, 0x30, 0x30, 0x30, 0x30, 0x78, 0x00,
12135	0x1e, 0x0c, 0x0c, 0x0c, 0xcc, 0xcc, 0x78, 0x00,
12136	0xe6, 0x66, 0x6c, 0x78, 0x6c, 0x66, 0xe6, 0x00,
12137	0xf0, 0x60, 0x60, 0x60, 0x62, 0x66, 0xfe, 0x00,
12138	0xc6, 0xee, 0xfe, 0xfe, 0xd6, 0xc6, 0xc6, 0x00,
12139	0xc6, 0xe6, 0xf6, 0xde, 0xce, 0xc6, 0xc6, 0x00,
12140	0x38, 0x6c, 0xc6, 0xc6, 0xc6, 0x6c, 0x38, 0x00,
12141	0xfc, 0x66, 0x66, 0x7c, 0x60, 0x60, 0xf0, 0x00,
12142	0x78, 0xcc, 0xcc, 0xcc, 0xdc, 0x78, 0x1c, 0x00,
12143	0xfc, 0x66, 0x66, 0x7c, 0x6c, 0x66, 0xe6, 0x00,
12144	0x78, 0xcc, 0xe0, 0x70, 0x1c, 0xcc, 0x78, 0x00,
12145	0xfc, 0xb4, 0x30, 0x30, 0x30, 0x30, 0x78, 0x00,
12146	0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0xfc, 0x00,
12147	0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0x78, 0x30, 0x00,
12148	0xc6, 0xc6, 0xc6, 0xd6, 0xfe, 0xee, 0xc6, 0x00,
12149	0xc6, 0xc6, 0x6c, 0x38, 0x38, 0x6c, 0xc6, 0x00,
12150	0xcc, 0xcc, 0xcc, 0x78, 0x30, 0x30, 0x78, 0x00,
12151	0xfe, 0xc6, 0x8c, 0x18, 0x32, 0x66, 0xfe, 0x00,
12152	0x78, 0x60, 0x60, 0x60, 0x60, 0x60, 0x78, 0x00,
12153	0xc0, 0x60, 0x30, 0x18, 0x0c, 0x06, 0x02, 0x00,
12154	0x78, 0x18, 0x18, 0x18, 0x18, 0x18, 0x78, 0x00,
12155	0x10, 0x38, 0x6c, 0xc6, 0x00, 0x00, 0x00, 0x00,
12156	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xff,
12157	0x30, 0x30, 0x18, 0x00, 0x00, 0x00, 0x00, 0x00,
12158	0x00, 0x00, 0x78, 0x0c, 0x7c, 0xcc, 0x76, 0x00,
12159	0xe0, 0x60, 0x60, 0x7c, 0x66, 0x66, 0xdc, 0x00,
12160	0x00, 0x00, 0x78, 0xcc, 0xc0, 0xcc, 0x78, 0x00,
12161	0x1c, 0x0c, 0x0c, 0x7c, 0xcc, 0xcc, 0x76, 0x00,
12162	0x00, 0x00, 0x78, 0xcc, 0xfc, 0xc0, 0x78, 0x00,
12163	0x38, 0x6c, 0x60, 0xf0, 0x60, 0x60, 0xf0, 0x00,
12164	0x00, 0x00, 0x76, 0xcc, 0xcc, 0x7c, 0x0c, 0xf8,
12165	0xe0, 0x60, 0x6c, 0x76, 0x66, 0x66, 0xe6, 0x00,
12166	0x30, 0x00, 0x70, 0x30, 0x30, 0x30, 0x78, 0x00,
12167	0x0c, 0x00, 0x0c, 0x0c, 0x0c, 0xcc, 0xcc, 0x78,
12168	0xe0, 0x60, 0x66, 0x6c, 0x78, 0x6c, 0xe6, 0x00,
12169	0x70, 0x30, 0x30, 0x30, 0x30, 0x30, 0x78, 0x00,
12170	0x00, 0x00, 0xcc, 0xfe, 0xfe, 0xd6, 0xc6, 0x00,
12171	0x00, 0x00, 0xf8, 0xcc, 0xcc, 0xcc, 0xcc, 0x00,
12172	0x00, 0x00, 0x78, 0xcc, 0xcc, 0xcc, 0x78, 0x00,
12173	0x00, 0x00, 0xdc, 0x66, 0x66, 0x7c, 0x60, 0xf0,
12174	0x00, 0x00, 0x76, 0xcc, 0xcc, 0x7c, 0x0c, 0x1e,
12175	0x00, 0x00, 0xdc, 0x76, 0x66, 0x60, 0xf0, 0x00,
12176	0x00, 0x00, 0x7c, 0xc0, 0x78, 0x0c, 0xf8, 0x00,
12177	0x10, 0x30, 0x7c, 0x30, 0x30, 0x34, 0x18, 0x00,
12178	0x00, 0x00, 0xcc, 0xcc, 0xcc, 0xcc, 0x76, 0x00,
12179	0x00, 0x00, 0xcc, 0xcc, 0xcc, 0x78, 0x30, 0x00,
12180	0x00, 0x00, 0xc6, 0xd6, 0xfe, 0xfe, 0x6c, 0x00,
12181	0x00, 0x00, 0xc6, 0x6c, 0x38, 0x6c, 0xc6, 0x00,
12182	0x00, 0x00, 0xcc, 0xcc, 0xcc, 0x7c, 0x0c, 0xf8,
12183	0x00, 0x00, 0xfc, 0x98, 0x30, 0x64, 0xfc, 0x00,
12184	0x1c, 0x30, 0x30, 0xe0, 0x30, 0x30, 0x1c, 0x00,
12185	0x18, 0x18, 0x18, 0x00, 0x18, 0x18, 0x18, 0x00,
12186	0xe0, 0x30, 0x30, 0x1c, 0x30, 0x30, 0xe0, 0x00,
12187	0x76, 0xdc, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
12188	0x00, 0x10, 0x38, 0x6c, 0xc6, 0xc6, 0xfe, 0x00,
12189	};
12190
12191	ASM_START
12192	.org 0xcc00
12193	// bcc-generated data will be placed here
12194	ASM_END

Note: See TracBrowser for help on using the repository browser.

source: vbox/trunk/src/VBox/Devices/PC/BIOS/rombios.c@ 15712

Download in other formats: