/* $Id: ahci.c 69500 2017-10-28 15:14:05Z vboxsync $ */ /** @file * AHCI host adapter driver to boot from SATA disks. */ /* * Copyright (C) 2011-2017 Oracle Corporation * * This file is part of VirtualBox Open Source Edition (OSE), as * available from http://www.virtualbox.org. This file is free software; * you can redistribute it and/or modify it under the terms of the GNU * General Public License (GPL) as published by the Free Software * Foundation, in version 2 as it comes in the "COPYING" file of the * VirtualBox OSE distribution. VirtualBox OSE is distributed in the * hope that it will be useful, but WITHOUT ANY WARRANTY of any kind. */ #include #include #include "biosint.h" #include "ebda.h" #include "inlines.h" #include "pciutil.h" #include "vds.h" #if DEBUG_AHCI # define DBG_AHCI(...) BX_INFO(__VA_ARGS__) #else # define DBG_AHCI(...) #endif /* Number of S/G table entries in EDDS. */ #define NUM_EDDS_SG 16 /** * AHCI PRDT structure. */ typedef struct { uint32_t phys_addr; uint32_t something; uint32_t reserved; uint32_t len; } ahci_prdt; /** * SATA D2H FIS (Device to Host Frame Information Structure). */ typedef struct { uint8_t fis_type; /* 34h */ uint8_t intr; /* Bit 6 indicates interrupt status. */ uint8_t status; /* Status register. */ uint8_t error; /* Error register. */ uint8_t sec_no; /* Sector number register. */ uint8_t cyl_lo; /* Cylinder low register. */ uint8_t cyl_hi; /* Cylinder high register. */ uint8_t dev_hd; /* Device/head register. */ uint8_t sec_no_exp; /* Expanded sector number register. */ uint8_t cyl_lo_exp; /* Expanded cylinder low register. */ uint8_t cyl_hi_exp; /* Expanded cylinder high register. */ uint8_t resvd0; uint8_t sec_cn; /* Sector count register. */ uint8_t sec_cn_exp; /* Expanded sector count register. */ uint16_t resvd1; uint32_t resvd2; } fis_d2h; ct_assert(sizeof(fis_d2h) == 20); /** * AHCI controller data. */ typedef struct { /** The AHCI command list as defined by chapter 4.2.2 of the Intel AHCI spec. * Because the BIOS doesn't support NCQ only the first command header is defined * to save memory. - Must be aligned on a 1K boundary. */ uint32_t aCmdHdr[0x8]; /** Align the next structure on a 128 byte boundary. */ uint8_t abAlignment1[0x60]; /** The command table of one request as defined by chapter 4.2.3 of the Intel AHCI spec. * Must be aligned on 128 byte boundary. */ uint8_t abCmd[0x40]; /** The ATAPI command region. * Located 40h bytes after the beginning of the CFIS (Command FIS). */ uint8_t abAcmd[0x20]; /** Align the PRDT structure on a 128 byte boundary. */ uint8_t abAlignment2[0x20]; /** Physical Region Descriptor Table (PRDT) array. In other * words, a scatter/gather descriptor list. */ ahci_prdt aPrdt[16]; /** Memory for the received command FIS area as specified by chapter 4.2.1 * of the Intel AHCI spec. This area is normally 256 bytes big but to save memory * only the first 96 bytes are used because it is assumed that the controller * never writes to the UFIS or reserved area. - Must be aligned on a 256byte boundary. */ uint8_t abFisRecv[0x60]; /** Base I/O port for the index/data register pair. */ uint16_t iobase; /** Current port which uses the memory to communicate with the controller. */ uint8_t cur_port; /** Current PRD index (for pre/post skip). */ uint8_t cur_prd; /** Physical address of the sink buffer (for pre/post skip). */ uint32_t sink_buf_phys; /** Saved high bits of EAX. */ uint16_t saved_eax_hi; /** VDS EDDS DMA buffer descriptor structure. */ vds_edds edds; vds_sg edds_more_sg[NUM_EDDS_SG - 1]; } ahci_t; /* The AHCI specific data must fit into 1KB (statically allocated). */ ct_assert(sizeof(ahci_t) <= 1024); /** PCI configuration fields. */ #define PCI_CONFIG_CAP 0x34 #define PCI_CAP_ID_SATACR 0x12 #define VBOX_AHCI_NO_DEVICE 0xffff #define RT_BIT_32(bit) ((uint32_t)(1L << (bit))) /** Global register set. */ #define AHCI_HBA_SIZE 0x100 /// @todo what are the casts good for? #define AHCI_REG_CAP ((uint32_t)0x00) #define AHCI_REG_GHC ((uint32_t)0x04) # define AHCI_GHC_AE RT_BIT_32(31) # define AHCI_GHC_IR RT_BIT_32(1) # define AHCI_GHC_HR RT_BIT_32(0) #define AHCI_REG_IS ((uint32_t)0x08) #define AHCI_REG_PI ((uint32_t)0x0c) #define AHCI_REG_VS ((uint32_t)0x10) /** Per port register set. */ #define AHCI_PORT_SIZE 0x80 #define AHCI_REG_PORT_CLB 0x00 #define AHCI_REG_PORT_CLBU 0x04 #define AHCI_REG_PORT_FB 0x08 #define AHCI_REG_PORT_FBU 0x0c #define AHCI_REG_PORT_IS 0x10 # define AHCI_REG_PORT_IS_DHRS RT_BIT_32(0) # define AHCI_REG_PORT_IS_TFES RT_BIT_32(30) #define AHCI_REG_PORT_IE 0x14 #define AHCI_REG_PORT_CMD 0x18 # define AHCI_REG_PORT_CMD_ST RT_BIT_32(0) # define AHCI_REG_PORT_CMD_FRE RT_BIT_32(4) # define AHCI_REG_PORT_CMD_FR RT_BIT_32(14) # define AHCI_REG_PORT_CMD_CR RT_BIT_32(15) #define AHCI_REG_PORT_TFD 0x20 #define AHCI_REG_PORT_SIG 0x24 #define AHCI_REG_PORT_SSTS 0x28 #define AHCI_REG_PORT_SCTL 0x2c #define AHCI_REG_PORT_SERR 0x30 #define AHCI_REG_PORT_SACT 0x34 #define AHCI_REG_PORT_CI 0x38 /** Returns the absolute register offset from a given port and port register. */ #define AHCI_PORT_REG(port, reg) (AHCI_HBA_SIZE + (port) * AHCI_PORT_SIZE + (reg)) #define AHCI_REG_IDX 0 #define AHCI_REG_DATA 4 /** Writes the given value to a AHCI register. */ #define AHCI_WRITE_REG(iobase, reg, val) \ outpd((iobase) + AHCI_REG_IDX, reg); \ outpd((iobase) + AHCI_REG_DATA, val) /** Reads from a AHCI register. */ #define AHCI_READ_REG(iobase, reg, val) \ outpd((iobase) + AHCI_REG_IDX, reg); \ (val) = inpd((iobase) + AHCI_REG_DATA) /** Writes to the given port register. */ #define VBOXAHCI_PORT_WRITE_REG(iobase, port, reg, val) \ AHCI_WRITE_REG((iobase), AHCI_PORT_REG((port), (reg)), val) /** Reads from the given port register. */ #define VBOXAHCI_PORT_READ_REG(iobase, port, reg, val) \ AHCI_READ_REG((iobase), AHCI_PORT_REG((port), (reg)), val) #define ATA_CMD_IDENTIFY_DEVICE 0xEC #define ATA_CMD_IDENTIFY_PACKET 0xA1 #define ATA_CMD_PACKET 0xA0 #define AHCI_CMD_READ_DMA_EXT 0x25 #define AHCI_CMD_WRITE_DMA_EXT 0x35 /* Warning: Destroys high bits of EAX. */ uint32_t inpd(uint16_t port); #pragma aux inpd = \ ".386" \ "in eax, dx" \ "mov dx, ax" \ "shr eax, 16" \ "xchg ax, dx" \ parm [dx] value [dx ax] modify nomemory; /* Warning: Destroys high bits of EAX. */ void outpd(uint16_t port, uint32_t val); #pragma aux outpd = \ ".386" \ "xchg ax, cx" \ "shl eax, 16" \ "mov ax, cx" \ "out dx, eax" \ parm [dx] [cx ax] modify nomemory; /* Machinery to save/restore high bits of EAX. 32-bit port I/O needs to use * EAX, but saving/restoring EAX around each port access would be inefficient. * Instead, each externally callable routine must save the high bits before * modifying them and restore the high bits before exiting. */ /* Note: Reading high EAX bits destroys them - *must* be restored later. */ uint16_t eax_hi_rd(void); #pragma aux eax_hi_rd = \ ".386" \ "shr eax, 16" \ value [ax] modify nomemory; void eax_hi_wr(uint16_t); #pragma aux eax_hi_wr = \ ".386" \ "shl eax, 16" \ parm [ax] modify nomemory; void inline high_bits_save(ahci_t __far *ahci) { ahci->saved_eax_hi = eax_hi_rd(); } void inline high_bits_restore(ahci_t __far *ahci) { eax_hi_wr(ahci->saved_eax_hi); } /** * Sets a given set of bits in a register. */ static void inline ahci_ctrl_set_bits(uint16_t iobase, uint16_t reg, uint32_t mask) { outpd(iobase + AHCI_REG_IDX, reg); outpd(iobase + AHCI_REG_DATA, inpd(iobase + AHCI_REG_DATA) | mask); } /** * Clears a given set of bits in a register. */ static void inline ahci_ctrl_clear_bits(uint16_t iobase, uint16_t reg, uint32_t mask) { outpd(iobase + AHCI_REG_IDX, reg); outpd(iobase + AHCI_REG_DATA, inpd(iobase + AHCI_REG_DATA) & ~mask); } /** * Returns whether at least one of the bits in the given mask is set * for a register. */ static uint8_t inline ahci_ctrl_is_bit_set(uint16_t iobase, uint16_t reg, uint32_t mask) { outpd(iobase + AHCI_REG_IDX, reg); return (inpd(iobase + AHCI_REG_DATA) & mask) != 0; } /** * Extracts a range of bits from a register and shifts them * to the right. */ static uint16_t ahci_ctrl_extract_bits(uint32_t val, uint32_t mask, uint8_t shift) { return (val & mask) >> shift; } /** * Converts a segment:offset pair into a 32bit physical address. */ static uint32_t ahci_addr_to_phys(void __far *ptr) { return ((uint32_t)FP_SEG(ptr) << 4) + FP_OFF(ptr); } /** * Issues a command to the SATA controller and waits for completion. */ static void ahci_port_cmd_sync(ahci_t __far *ahci, uint8_t val) { uint16_t io_base; uint8_t port; port = ahci->cur_port; io_base = ahci->iobase; if (port != 0xff) { /* Prepare the command header. */ ahci->aCmdHdr[0] = ((uint32_t)ahci->cur_prd << 16) | RT_BIT_32(7) | val; ahci->aCmdHdr[1] = 0; ahci->aCmdHdr[2] = ahci_addr_to_phys(&ahci->abCmd[0]); /* Enable Command and FIS receive engine. */ ahci_ctrl_set_bits(io_base, AHCI_PORT_REG(port, AHCI_REG_PORT_CMD), AHCI_REG_PORT_CMD_FRE | AHCI_REG_PORT_CMD_ST); /* Queue command. */ VBOXAHCI_PORT_WRITE_REG(io_base, port, AHCI_REG_PORT_CI, 0x1); /* Wait for a D2H FIS. */ DBG_AHCI("AHCI: Waiting for D2H FIS\n"); while (ahci_ctrl_is_bit_set(io_base, AHCI_PORT_REG(port, AHCI_REG_PORT_IS), AHCI_REG_PORT_IS_DHRS | AHCI_REG_PORT_IS_TFES) == 0) { // This is where we'd need some kind of a yield functionality... } ahci_ctrl_set_bits(io_base, AHCI_PORT_REG(port, AHCI_REG_PORT_IS), AHCI_REG_PORT_IS_DHRS); /* Acknowledge received D2H FIS. */ /* Disable command engine. */ ahci_ctrl_clear_bits(io_base, AHCI_PORT_REG(port, AHCI_REG_PORT_CMD), AHCI_REG_PORT_CMD_ST); /* Caller must examine status. */ } else DBG_AHCI("AHCI: Invalid port given\n"); } /** * Issue command to device. */ static uint16_t ahci_cmd_data(bio_dsk_t __far *bios_dsk, uint8_t cmd) { ahci_t __far *ahci = bios_dsk->ahci_seg :> 0; uint16_t n_sect = bios_dsk->drqp.nsect; uint16_t sectsz = bios_dsk->drqp.sect_sz; fis_d2h __far *d2h; _fmemset(&ahci->abCmd[0], 0, sizeof(ahci->abCmd)); /* Prepare the FIS. */ ahci->abCmd[0] = 0x27; /* FIS type H2D. */ ahci->abCmd[1] = 1 << 7; /* Command update. */ ahci->abCmd[2] = cmd; ahci->abCmd[3] = 0; ahci->abCmd[4] = bios_dsk->drqp.lba & 0xff; ahci->abCmd[5] = (bios_dsk->drqp.lba >> 8) & 0xff; ahci->abCmd[6] = (bios_dsk->drqp.lba >> 16) & 0xff; ahci->abCmd[7] = RT_BIT_32(6); /* LBA access. */ ahci->abCmd[8] = (bios_dsk->drqp.lba >> 24) & 0xff; ahci->abCmd[9] = (bios_dsk->drqp.lba >> 32) & 0xff; ahci->abCmd[10] = (bios_dsk->drqp.lba >> 40) & 0xff; ahci->abCmd[11] = 0; ahci->abCmd[12] = (uint8_t)(n_sect & 0xff); ahci->abCmd[13] = (uint8_t)((n_sect >> 8) & 0xff); /* Lock memory needed for DMA. */ ahci->edds.num_avail = NUM_EDDS_SG; DBG_AHCI("AHCI: S/G list for %lu bytes (skip %u)\n", (uint32_t)n_sect * sectsz, bios_dsk->drqp.skip_a); vds_build_sg_list(&ahci->edds, bios_dsk->drqp.buffer, (uint32_t)n_sect * sectsz); /* Set up the PRDT. */ ahci->aPrdt[ahci->cur_prd].len = ahci->edds.u.sg[0].size - 1; ahci->aPrdt[ahci->cur_prd].phys_addr = ahci->edds.u.sg[0].phys_addr; ++ahci->cur_prd; if (bios_dsk->drqp.skip_a) { ahci->aPrdt[ahci->cur_prd].len = bios_dsk->drqp.skip_a - 1; ahci->aPrdt[ahci->cur_prd].phys_addr = ahci->sink_buf_phys; ++ahci->cur_prd; } #if DEBUG_AHCI { uint16_t prdt_idx; for (prdt_idx = 0; prdt_idx < ahci->cur_prd; ++prdt_idx) { DBG_AHCI("S/G entry %u: %5lu bytes @ %08lX\n", prdt_idx, ahci->aPrdt[prdt_idx].len + 1, ahci->aPrdt[prdt_idx].phys_addr); } } #endif /* Build variable part of first command DWORD (reuses 'cmd'). */ if (cmd == AHCI_CMD_WRITE_DMA_EXT) cmd = RT_BIT_32(6); /* Indicate a write to device. */ else if (cmd == ATA_CMD_PACKET) { cmd |= RT_BIT_32(5); /* Indicate ATAPI command. */ ahci->abCmd[3] |= 1; /* DMA transfers. */ } else cmd = 0; cmd |= 5; /* Five DWORDs. */ ahci_port_cmd_sync(ahci, cmd); /* Examine operation status. */ d2h = (void __far *)&ahci->abFisRecv[0x40]; DBG_AHCI("AHCI: ERR=%02x, STAT=%02x, SCNT=%02x\n", d2h->error, d2h->status, d2h->sec_cn); /* Unlock the buffer again. */ vds_free_sg_list(&ahci->edds); return d2h->error ? 4 : 0; } /** * Deinits the curent active port. */ static void ahci_port_deinit_current(ahci_t __far *ahci) { uint16_t io_base; uint8_t port; io_base = ahci->iobase; port = ahci->cur_port; if (port != 0xff) { /* Put the port into an idle state. */ ahci_ctrl_clear_bits(io_base, AHCI_PORT_REG(port, AHCI_REG_PORT_CMD), AHCI_REG_PORT_CMD_FRE | AHCI_REG_PORT_CMD_ST); while (ahci_ctrl_is_bit_set(io_base, AHCI_PORT_REG(port, AHCI_REG_PORT_CMD), AHCI_REG_PORT_CMD_FRE | AHCI_REG_PORT_CMD_ST | AHCI_REG_PORT_CMD_FR | AHCI_REG_PORT_CMD_CR) == 1) { DBG_AHCI("AHCI: Waiting for the port to idle\n"); } /* * Port idles, set up memory for commands and received FIS and program the * address registers. */ /// @todo merge memsets? _fmemset(&ahci->aCmdHdr[0], 0, sizeof(ahci->aCmdHdr)); _fmemset(&ahci->abCmd[0], 0, sizeof(ahci->abCmd)); _fmemset(&ahci->abFisRecv[0], 0, sizeof(ahci->abFisRecv)); VBOXAHCI_PORT_WRITE_REG(io_base, port, AHCI_REG_PORT_FB, 0); VBOXAHCI_PORT_WRITE_REG(io_base, port, AHCI_REG_PORT_FBU, 0); VBOXAHCI_PORT_WRITE_REG(io_base, port, AHCI_REG_PORT_CLB, 0); VBOXAHCI_PORT_WRITE_REG(io_base, port, AHCI_REG_PORT_CLBU, 0); /* Disable all interrupts. */ VBOXAHCI_PORT_WRITE_REG(io_base, port, AHCI_REG_PORT_IE, 0); ahci->cur_port = 0xff; } } /** * Brings a port into a minimal state to make device detection possible * or to queue requests. */ static void ahci_port_init(ahci_t __far *ahci, uint8_t u8Port) { /* Deinit any other port first. */ ahci_port_deinit_current(ahci); /* Put the port into an idle state. */ ahci_ctrl_clear_bits(ahci->iobase, AHCI_PORT_REG(u8Port, AHCI_REG_PORT_CMD), AHCI_REG_PORT_CMD_FRE | AHCI_REG_PORT_CMD_ST); while (ahci_ctrl_is_bit_set(ahci->iobase, AHCI_PORT_REG(u8Port, AHCI_REG_PORT_CMD), AHCI_REG_PORT_CMD_FRE | AHCI_REG_PORT_CMD_ST | AHCI_REG_PORT_CMD_FR | AHCI_REG_PORT_CMD_CR) == 1) { DBG_AHCI("AHCI: Waiting for the port to idle\n"); } /* * Port idles, set up memory for commands and received FIS and program the * address registers. */ /// @todo just one memset? _fmemset(&ahci->aCmdHdr[0], 0, sizeof(ahci->aCmdHdr)); _fmemset(&ahci->abCmd[0], 0, sizeof(ahci->abCmd)); _fmemset(&ahci->abFisRecv[0], 0, sizeof(ahci->abFisRecv)); DBG_AHCI("AHCI: FIS receive area %lx from %x:%x\n", ahci_addr_to_phys(&ahci->abFisRecv), FP_SEG(ahci->abFisRecv), FP_OFF(ahci->abFisRecv)); VBOXAHCI_PORT_WRITE_REG(ahci->iobase, u8Port, AHCI_REG_PORT_FB, ahci_addr_to_phys(&ahci->abFisRecv)); VBOXAHCI_PORT_WRITE_REG(ahci->iobase, u8Port, AHCI_REG_PORT_FBU, 0); DBG_AHCI("AHCI: CMD list area %lx\n", ahci_addr_to_phys(&ahci->aCmdHdr)); VBOXAHCI_PORT_WRITE_REG(ahci->iobase, u8Port, AHCI_REG_PORT_CLB, ahci_addr_to_phys(&ahci->aCmdHdr)); VBOXAHCI_PORT_WRITE_REG(ahci->iobase, u8Port, AHCI_REG_PORT_CLBU, 0); /* Disable all interrupts. */ VBOXAHCI_PORT_WRITE_REG(ahci->iobase, u8Port, AHCI_REG_PORT_IE, 0); VBOXAHCI_PORT_WRITE_REG(ahci->iobase, u8Port, AHCI_REG_PORT_IS, 0xffffffff); /* Clear all errors. */ VBOXAHCI_PORT_WRITE_REG(ahci->iobase, u8Port, AHCI_REG_PORT_SERR, 0xffffffff); ahci->cur_port = u8Port; ahci->cur_prd = 0; } /** * Read sectors from an attached AHCI device. * * @returns status code. * @param bios_dsk Pointer to disk request packet (in the * EBDA). */ int ahci_read_sectors(bio_dsk_t __far *bios_dsk) { uint16_t device_id; uint16_t rc; device_id = VBOX_GET_AHCI_DEVICE(bios_dsk->drqp.dev_id); if (device_id > BX_MAX_AHCI_DEVICES) BX_PANIC("%s: device_id out of range %d\n", __func__, device_id); DBG_AHCI("%s: %u sectors @ LBA 0x%llx, device %d, port %d\n", __func__, bios_dsk->drqp.nsect, bios_dsk->drqp.lba, device_id, bios_dsk->ahcidev[device_id].port); high_bits_save(bios_dsk->ahci_seg :> 0); ahci_port_init(bios_dsk->ahci_seg :> 0, bios_dsk->ahcidev[device_id].port); rc = ahci_cmd_data(bios_dsk, AHCI_CMD_READ_DMA_EXT); DBG_AHCI("%s: transferred %lu bytes\n", __func__, ((ahci_t __far *)(bios_dsk->ahci_seg :> 0))->aCmdHdr[1]); bios_dsk->drqp.trsfsectors = bios_dsk->drqp.nsect; #ifdef DMA_WORKAROUND rep_movsw(bios_dsk->drqp.buffer, bios_dsk->drqp.buffer, bios_dsk->drqp.nsect * 512 / 2); #endif high_bits_restore(bios_dsk->ahci_seg :> 0); return rc; } /** * Write sectors to an attached AHCI device. * * @returns status code. * @param bios_dsk Pointer to disk request packet (in the * EBDA). */ int ahci_write_sectors(bio_dsk_t __far *bios_dsk) { uint16_t device_id; uint16_t rc; device_id = VBOX_GET_AHCI_DEVICE(bios_dsk->drqp.dev_id); if (device_id > BX_MAX_AHCI_DEVICES) BX_PANIC("%s: device_id out of range %d\n", __func__, device_id); DBG_AHCI("%s: %u sectors @ LBA 0x%llx, device %d, port %d\n", __func__, bios_dsk->drqp.nsect, bios_dsk->drqp.lba, device_id, bios_dsk->ahcidev[device_id].port); high_bits_save(bios_dsk->ahci_seg :> 0); ahci_port_init(bios_dsk->ahci_seg :> 0, bios_dsk->ahcidev[device_id].port); rc = ahci_cmd_data(bios_dsk, AHCI_CMD_WRITE_DMA_EXT); DBG_AHCI("%s: transferred %lu bytes\n", __func__, ((ahci_t __far *)(bios_dsk->ahci_seg :> 0))->aCmdHdr[1]); bios_dsk->drqp.trsfsectors = bios_dsk->drqp.nsect; high_bits_restore(bios_dsk->ahci_seg :> 0); return rc; } /// @todo move #define ATA_DATA_NO 0x00 #define ATA_DATA_IN 0x01 #define ATA_DATA_OUT 0x02 uint16_t ahci_cmd_packet(uint16_t device_id, uint8_t cmdlen, char __far *cmdbuf, uint16_t skip_b, uint32_t length, uint8_t inout, char __far *buffer) { bio_dsk_t __far *bios_dsk = read_word(0x0040, 0x000E) :> &EbdaData->bdisk; ahci_t __far *ahci; /* Data out is currently not supported. */ if (inout == ATA_DATA_OUT) { BX_INFO("%s: DATA_OUT not supported yet\n", __func__); return 1; } /* The skip length must be even. */ if (skip_b & 1) { DBG_AHCI("%s: skip must be even (%04x)\n", __func__, skip_b); return 1; } /* Convert to AHCI specific device number. */ device_id = VBOX_GET_AHCI_DEVICE(device_id); DBG_AHCI("%s: reading %lu bytes, skip %u/%u, device %d, port %d\n", __func__, length, bios_dsk->drqp.skip_b, bios_dsk->drqp.skip_a, device_id, bios_dsk->ahcidev[device_id].port); DBG_AHCI("%s: reading %u %u-byte sectors\n", __func__, bios_dsk->drqp.nsect, bios_dsk->drqp.sect_sz); bios_dsk->drqp.lba = length << 8; /// @todo xfer length limit bios_dsk->drqp.buffer = buffer; bios_dsk->drqp.nsect = length / bios_dsk->drqp.sect_sz; // bios_dsk->drqp.sect_sz = 2048; ahci = bios_dsk->ahci_seg :> 0; high_bits_save(ahci); ahci_port_init(bios_dsk->ahci_seg :> 0, bios_dsk->ahcidev[device_id].port); /* Copy the ATAPI command where the HBA can fetch it. */ _fmemcpy(ahci->abAcmd, cmdbuf, cmdlen); /* Reset transferred counts. */ /// @todo clear in calling code? bios_dsk->drqp.trsfsectors = 0; bios_dsk->drqp.trsfbytes = 0; /* Set up a PRD entry to throw away the beginning of the transfer. */ if (bios_dsk->drqp.skip_b) { ahci->aPrdt[0].len = bios_dsk->drqp.skip_b - 1; ahci->aPrdt[0].phys_addr = ahci->sink_buf_phys; ahci->cur_prd++; } ahci_cmd_data(bios_dsk, ATA_CMD_PACKET); DBG_AHCI("%s: transferred %lu bytes\n", __func__, ahci->aCmdHdr[1]); bios_dsk->drqp.trsfbytes = ahci->aCmdHdr[1]; #ifdef DMA_WORKAROUND rep_movsw(bios_dsk->drqp.buffer, bios_dsk->drqp.buffer, bios_dsk->drqp.trsfbytes / 2); #endif high_bits_restore(ahci); return ahci->aCmdHdr[1] == 0 ? 4 : 0; } /* Wait for the specified number of BIOS timer ticks or data bytes. */ void wait_ticks_device_init( unsigned wait_ticks, unsigned wait_bytes ) { } void ahci_port_detect_device(ahci_t __far *ahci, uint8_t u8Port) { uint32_t val; bio_dsk_t __far *bios_dsk; volatile uint32_t __far *ticks; uint32_t end_tick; int device_found = 0; ahci_port_init(ahci, u8Port); bios_dsk = read_word(0x0040, 0x000E) :> &EbdaData->bdisk; /* Reset connection. */ VBOXAHCI_PORT_WRITE_REG(ahci->iobase, u8Port, AHCI_REG_PORT_SCTL, 0x01); /* * According to the spec we should wait at least 1msec until the reset * is cleared but this is a virtual controller so we don't have to. */ VBOXAHCI_PORT_WRITE_REG(ahci->iobase, u8Port, AHCI_REG_PORT_SCTL, 0); /* * We do however have to wait for the device to initialize (the port reset * to complete). That can take up to 10ms according to the SATA spec (device * must send COMINIT within 10ms of COMRESET). We should be generous with * the wait because in the typical case there are no ports without a device * attached. */ ticks = MK_FP( 0x40, 0x6C ); end_tick = *ticks + 3; /* Wait up to five BIOS ticks, something in 150ms range. */ while( *ticks < end_tick ) { /* If PxSSTS.DET is 3, everything went fine. */ VBOXAHCI_PORT_READ_REG(ahci->iobase, u8Port, AHCI_REG_PORT_SSTS, val); if (ahci_ctrl_extract_bits(val, 0xfL, 0) == 3) { device_found = 1; break; } } /* Timed out, no device detected. */ if (!device_found) { DBG_AHCI("AHCI: Timed out, no device detected on port %d\n", u8Port); return; } if (ahci_ctrl_extract_bits(val, 0xfL, 0) == 0x3) { uint8_t abBuffer[0x0200]; uint8_t hdcount, devcount_ahci, hd_index; uint8_t cdcount; uint8_t removable; /* Clear all errors after the reset. */ VBOXAHCI_PORT_WRITE_REG(ahci->iobase, u8Port, AHCI_REG_PORT_SERR, 0xffffffff); devcount_ahci = bios_dsk->ahci_devcnt; DBG_AHCI("AHCI: Device detected on port %d\n", u8Port); /// @todo Merge common HD/CDROM detection code if (devcount_ahci < BX_MAX_AHCI_DEVICES) { /* Device detected, enable FIS receive. */ ahci_ctrl_set_bits(ahci->iobase, AHCI_PORT_REG(u8Port, AHCI_REG_PORT_CMD), AHCI_REG_PORT_CMD_FRE); /* Check signature to determine device type. */ VBOXAHCI_PORT_READ_REG(ahci->iobase, u8Port, AHCI_REG_PORT_SIG, val); if (val == 0x101) { uint64_t sectors; uint16_t cylinders, heads, spt; chs_t lgeo; uint8_t idxCmosChsBase; DBG_AHCI("AHCI: Detected hard disk\n"); /* Identify device. */ bios_dsk->drqp.lba = 0; bios_dsk->drqp.buffer = &abBuffer; bios_dsk->drqp.nsect = 1; bios_dsk->drqp.sect_sz = 512; ahci_cmd_data(bios_dsk, ATA_CMD_IDENTIFY_DEVICE); /* Calculate index into the generic device table. */ hd_index = devcount_ahci + BX_MAX_ATA_DEVICES + BX_MAX_SCSI_DEVICES; removable = *(abBuffer+0) & 0x80 ? 1 : 0; cylinders = *(uint16_t *)(abBuffer+(1*2)); // word 1 heads = *(uint16_t *)(abBuffer+(3*2)); // word 3 spt = *(uint16_t *)(abBuffer+(6*2)); // word 6 sectors = *(uint32_t *)(abBuffer+(60*2)); // word 60 and word 61 if (sectors == 0x0FFFFFFF) /* For disks bigger than ~128GB */ sectors = *(uint64_t *)(abBuffer+(100*2)); // words 100 to 103 DBG_AHCI("AHCI: 0x%llx sectors\n", sectors); bios_dsk->ahcidev[devcount_ahci].port = u8Port; bios_dsk->devices[hd_index].type = DSK_TYPE_AHCI; bios_dsk->devices[hd_index].device = DSK_DEVICE_HD; bios_dsk->devices[hd_index].removable = removable; bios_dsk->devices[hd_index].lock = 0; bios_dsk->devices[hd_index].blksize = 512; bios_dsk->devices[hd_index].translation = GEO_TRANSLATION_LBA; bios_dsk->devices[hd_index].sectors = sectors; bios_dsk->devices[hd_index].pchs.heads = heads; bios_dsk->devices[hd_index].pchs.cylinders = cylinders; bios_dsk->devices[hd_index].pchs.spt = spt; /* Get logical CHS geometry. */ switch (devcount_ahci) { case 0: idxCmosChsBase = 0x40; break; case 1: idxCmosChsBase = 0x48; break; case 2: idxCmosChsBase = 0x50; break; case 3: idxCmosChsBase = 0x58; break; default: idxCmosChsBase = 0; } if (idxCmosChsBase && inb_cmos(idxCmosChsBase+7)) { lgeo.cylinders = inb_cmos(idxCmosChsBase + 0) + (inb_cmos(idxCmosChsBase + 1) << 8); lgeo.heads = inb_cmos(idxCmosChsBase + 2); lgeo.spt = inb_cmos(idxCmosChsBase + 7); } else set_geom_lba(&lgeo, sectors); /* Default EDD-style translated LBA geometry. */ BX_INFO("AHCI %d-P#%d: PCHS=%u/%u/%u LCHS=%u/%u/%u 0x%llx sectors\n", devcount_ahci, u8Port, cylinders, heads, spt, lgeo.cylinders, lgeo.heads, lgeo.spt, sectors); bios_dsk->devices[hd_index].lchs = lgeo; /* Store the ID of the disk in the BIOS hdidmap. */ hdcount = bios_dsk->hdcount; bios_dsk->hdidmap[hdcount] = devcount_ahci + BX_MAX_ATA_DEVICES + BX_MAX_SCSI_DEVICES; hdcount++; bios_dsk->hdcount = hdcount; /* Update hdcount in the BDA. */ hdcount = read_byte(0x40, 0x75); hdcount++; write_byte(0x40, 0x75, hdcount); } else if (val == 0xeb140101) { DBG_AHCI("AHCI: Detected ATAPI device\n"); /* Identify packet device. */ bios_dsk->drqp.lba = 0; bios_dsk->drqp.buffer = &abBuffer; bios_dsk->drqp.nsect = 1; bios_dsk->drqp.sect_sz = 512; ahci_cmd_data(bios_dsk, ATA_CMD_IDENTIFY_PACKET); /* Calculate index into the generic device table. */ hd_index = devcount_ahci + BX_MAX_ATA_DEVICES + BX_MAX_SCSI_DEVICES; removable = *(abBuffer+0) & 0x80 ? 1 : 0; bios_dsk->ahcidev[devcount_ahci].port = u8Port; bios_dsk->devices[hd_index].type = DSK_TYPE_AHCI; bios_dsk->devices[hd_index].device = DSK_DEVICE_CDROM; bios_dsk->devices[hd_index].removable = removable; bios_dsk->devices[hd_index].blksize = 2048; /* Store the ID of the device in the BIOS cdidmap. */ cdcount = bios_dsk->cdcount; bios_dsk->cdidmap[cdcount] = devcount_ahci + BX_MAX_ATA_DEVICES + BX_MAX_SCSI_DEVICES; cdcount++; bios_dsk->cdcount = cdcount; } else DBG_AHCI("AHCI: Ignoring unknown device\n"); devcount_ahci++; bios_dsk->ahci_devcnt = devcount_ahci; } else DBG_AHCI("AHCI: Reached maximum device count, skipping\n"); } } /** * Allocates 1K of conventional memory. */ static uint16_t ahci_mem_alloc(void) { uint16_t base_mem_kb; uint16_t ahci_seg; base_mem_kb = read_word(0x00, 0x0413); DBG_AHCI("AHCI: %dK of base mem\n", base_mem_kb); if (base_mem_kb == 0) return 0; base_mem_kb--; /* Allocate one block. */ ahci_seg = (((uint32_t)base_mem_kb * 1024) >> 4); /* Calculate start segment. */ write_word(0x00, 0x0413, base_mem_kb); return ahci_seg; } /** * Initializes the AHCI HBA and detects attached devices. */ static int ahci_hba_init(uint16_t io_base) { uint8_t i, cPorts; uint32_t val; uint16_t ebda_seg; uint16_t ahci_seg; bio_dsk_t __far *bios_dsk; ahci_t __far *ahci; ebda_seg = read_word(0x0040, 0x000E); bios_dsk = ebda_seg :> &EbdaData->bdisk; AHCI_READ_REG(io_base, AHCI_REG_VS, val); DBG_AHCI("AHCI: Controller version: 0x%x (major) 0x%x (minor)\n", ahci_ctrl_extract_bits(val, 0xffff0000, 16), ahci_ctrl_extract_bits(val, 0x0000ffff, 0)); /* Allocate 1K of base memory. */ ahci_seg = ahci_mem_alloc(); if (ahci_seg == 0) { DBG_AHCI("AHCI: Could not allocate 1K of memory, can't boot from controller\n"); return 0; } DBG_AHCI("AHCI: ahci_seg=%04x, size=%04x, pointer at EBDA:%04x (EBDA size=%04x)\n", ahci_seg, sizeof(ahci_t), (uint16_t)&EbdaData->bdisk.ahci_seg, sizeof(ebda_data_t)); bios_dsk->ahci_seg = ahci_seg; bios_dsk->ahci_devcnt = 0; ahci = ahci_seg :> 0; ahci->cur_port = 0xff; ahci->iobase = io_base; /* Physical address of memory used for throwing away ATAPI data when reading 512-byte * blocks from 2048-byte CD sectors. */ ahci->sink_buf_phys = 0xCC000; /// @todo find some better place! /* Reset the controller. */ ahci_ctrl_set_bits(io_base, AHCI_REG_GHC, AHCI_GHC_HR); do { AHCI_READ_REG(io_base, AHCI_REG_GHC, val); } while ((val & AHCI_GHC_HR) != 0); AHCI_READ_REG(io_base, AHCI_REG_CAP, val); cPorts = ahci_ctrl_extract_bits(val, 0x1f, 0) + 1; /* Extract number of ports.*/ DBG_AHCI("AHCI: HBA has %u ports\n", cPorts); /* Go through the ports. */ i = 0; while (i < 32) { if (ahci_ctrl_is_bit_set(io_base, AHCI_REG_PI, RT_BIT_32(i)) != 0) { DBG_AHCI("AHCI: Port %u is present\n", i); ahci_port_detect_device(ahci_seg :> 0, i); cPorts--; if (cPorts == 0) break; } i++; } return 0; } /** * Init the AHCI driver and detect attached disks. */ void BIOSCALL ahci_init(void) { uint16_t busdevfn; busdevfn = pci_find_classcode(0x00010601); if (busdevfn != VBOX_AHCI_NO_DEVICE) { uint8_t u8Bus, u8DevFn; uint8_t u8PciCapOff; u8Bus = (busdevfn & 0xff00) >> 8; u8DevFn = busdevfn & 0x00ff; DBG_AHCI("AHCI HBA at Bus %u DevFn 0x%x (raw 0x%x)\n", u8Bus, u8DevFn, busdevfn); /* Examine the capability list and search for the Serial ATA Capability Register. */ u8PciCapOff = pci_read_config_byte(u8Bus, u8DevFn, PCI_CONFIG_CAP); while (u8PciCapOff != 0) { uint8_t u8PciCapId = pci_read_config_byte(u8Bus, u8DevFn, u8PciCapOff); DBG_AHCI("Capability ID 0x%x at 0x%x\n", u8PciCapId, u8PciCapOff); if (u8PciCapId == PCI_CAP_ID_SATACR) break; /* Go on to the next capability. */ u8PciCapOff = pci_read_config_byte(u8Bus, u8DevFn, u8PciCapOff + 1); } if (u8PciCapOff != 0) { uint8_t u8Rev; DBG_AHCI("AHCI HBA with SATA Capability register at 0x%x\n", u8PciCapOff); /* Advance to the stuff behind the id and next capability pointer. */ u8PciCapOff += 2; u8Rev = pci_read_config_byte(u8Bus, u8DevFn, u8PciCapOff); if (u8Rev == 0x10) { /* Read the SATACR1 register and get the bar and offset of the index/data pair register. */ uint8_t u8Bar = 0x00; uint16_t u16Off = 0x00; uint16_t u16BarOff = pci_read_config_word(u8Bus, u8DevFn, u8PciCapOff + 2); DBG_AHCI("SATACR1: 0x%x\n", u16BarOff); switch (u16BarOff & 0xf) { case 0x04: u8Bar = 0x10; break; case 0x05: u8Bar = 0x14; break; case 0x06: u8Bar = 0x18; break; case 0x07: u8Bar = 0x1c; break; case 0x08: u8Bar = 0x20; break; case 0x09: u8Bar = 0x24; break; case 0x0f: default: /* Reserved or unsupported. */ DBG_AHCI("BAR 0x%x unsupported\n", u16BarOff & 0xf); } /* Get the offset inside the BAR from bits 4:15. */ u16Off = (u16BarOff >> 4) * 4; if (u8Bar != 0x00) { uint32_t u32Bar = pci_read_config_dword(u8Bus, u8DevFn, u8Bar); DBG_AHCI("BAR at 0x%x : 0x%x\n", u8Bar, u32Bar); if ((u32Bar & 0x01) != 0) { int rc; uint16_t u16AhciIoBase = (u32Bar & 0xfff0) + u16Off; /* Enable PCI memory, I/O, bus mastering access in command register. */ pci_write_config_word(u8Bus, u8DevFn, 4, 0x7); DBG_AHCI("I/O base: 0x%x\n", u16AhciIoBase); rc = ahci_hba_init(u16AhciIoBase); } else DBG_AHCI("BAR is MMIO\n"); } } else DBG_AHCI("Invalid revision 0x%x\n", u8Rev); } else DBG_AHCI("AHCI HBA with no usable Index/Data register pair!\n"); } else DBG_AHCI("No AHCI HBA!\n"); }